SMARTdesks flipIT Lift Desk DFL-722630-T23-THB User manual

DFL-722630-T23-THB or DFL-722630-T23-TLB
Double flipIT Lift Desk
Includes two flipIT Lift monitor supports (push open/close, holds one monitor per user, each moni-
tor 5-15 or 15-24 lbs and up to 23”wide, monitor can tilt), two 26”x 8”keyboard/mouse trays with
integrated mouse fence and wire management pass through, two CPU bays (to right of users),
80mm side access grommets; top surface finished with high-pressure laminate, base finished in
melamine, PVC edge trim (semi-rigid); design includes contoured, arched panels and radius cor-
ners; includes 1.25”steel floor leveling glides with .75”adjustment; 72”W x 26”D x 30”H.
www.smartdesks.com
800 770 7042
flipIT Lift Desk®
How to assemble SMARTdesks®
flipIT Lift Desks® — Singles and Doubles.
This manual shows the approach for assembling all models by
focusing on the single with CPU bay and KB26 dual arm
keyboard tray.
Tools Required:
• Phillips #2 and #3 drive
• Torx T20 driver
• 3/8”open end wrench
SFL-402630-T23-THB or SFL-402630-T23-TLB
Single flipIT Lift Desk
Includes flipIT Lift monitor support (push open/close, holds one monitor 5-15 or 15-24 lbs
and up to 23”wide, monitor can tilt), one 26”x 8” keyboard/mouse tray with integrated mouse
fence and wire management pass through, one CPU bay to right of user, 80mm side access
grommets; top surface finished with high-pressure laminate, base finished in melamine, PVC
edge trim (semi-rigid); design includes contoured, arched panels and radius corners; includes
1.25”steel floor leveling glides with .75” adjustment; 40”W x 26”D x 30” H.
© 2015 CBT Supply Inc dba SMARTdesks® All rights reserved. SMARTdesks® and flipIT® are registered trademarks of CBT Supply, Inc. rev12042015
ASSEMBLY INSTRUCTIONS
Verify the weight of your monitor
Models ending in THB are for monitors weighing 15-24 lbs.
Models ending in TLB for monitors weighing 5-15 lbs.

Parts Identification
The top includes
male RV clips which
are used to attach
the top to the
vertical sides and
CPU bay panels.
Keyboard tray pilots
are pre-drilled.
RV clips mounted in
top and to side panels.
The keyboard kit includes
L brackets and self-tapping
metal screws , plus eight #8
#10 thread 5/8” pan head
Phillips #2 wood screws
Monitor safety panel in-
stalls with Keku clips. Pilot
holes are pre drilled and
wood screws supplied.
Male and female Keku clips
with wood screws.
CPU bay panel
with pilots for
Keku clips and
cams for pins.
CPU bay
bottom with
cams for pins
installed
Side panel with
RV clips, gliders,
holes drilled for
cam pins and
80mm grommet.
Cam pins
Side panel with
RV clips, gliders,
holes drilled for
cam pins and
80mm grommet.
Back panel with
pilots for installing
monitor lift and
cams for fastening
cam pins.
VESA monitor mount and
tilter, installs to monitor
lift with Torx T20 screws
and 3/8”open end nuts.
Monitor mount lid, with
bracket and wood screws.
80mm grommets
Motorless monitor lift mechanism.
There are variations of parts
and counts based on single
and double desk designs, and
number and configuration of
(or exclusion of) CPU bays.
flipIT Lift Desk Assembly ©2015 CBT Supply, Inc. 2 Technical Support: 800-770-7042

Getting started
Prepare a place for assembly on a carpeted
floor and at workbench height with a furniture
blanket to protect the furniture surfaces.
Identify the parts and get a sense for how
they fit together from the preceding page. On
the back page of the manual, each model is
illustrated to help you see where CPU bays are
located (if they are included).
Prepare lift mechanism for
mounting
The lift mechanism ships with a safety screw
and clip. Remove the screw with a wrench.
Place the mechanism on the floor, carefully push down and compress the
unit until it releases, then give resistance to let the monitor lift fully extend.
Note: In these close-up details, the mechanism was photographed when it was already installed to the desk back panel. Below, the mechanism is
shown as it is shipped for assembly.
flipIT Lift Desk Assembly ©2015 CBT Supply, Inc. 3 Technical Support: 800-770-7042

flipIT Lift Desk Assembly ©2015 CBT Supply, Inc. 4 Technical Support: 800-770-7042
Install the monitor lift mech
Secure the fully extended mechanism to the
back base panel using the pilot holes provided
and #10, 5/8”pan head #3 Phillips screws with
a power screw gun.
Place desktop on carpeted or blanketed floor.
This pre-assembly can be done any time prior
to desk assembly. It is shown first to prevent
mishap in handling the lift mech.
Male RV Clip
Keyboard Pilot Holes
If male RV clips are not pre-installed, press them into position as shown.

flipIT Lift Desk Assembly ©2015 CBT Supply, Inc. 5 Technical Support: 800-770-7042
Left side panel with
Male Keku clips
and Female RV clips
pre-installed.
Press RV clips into
position and install
Male KeKu clips with
wood screws as
needed.
Male Keku clips
with screws
Female RV clips
Pre-install Keku clips and
RV clips to left side panel
Install left side panel to
desktop
Use #2 Phillips drive to tighten RV clips
Pre-install Keku clips and RV clips
to CPU Bay panel
Note orientation of the Keku clips, installed with wood
screws.
The illustration shows both sides of the CPU Bay panel.
Install CPU Bay panel to desktop
Use #2 Phillips drive to tighten RV clips
Install Right Side panel to desktop
Use #2 Phillips drive to tighten RV clips

flipIT Lift Desk Assembly ©2015 CBT Supply, Inc. 6 Technical Support: 800-770-7042
Use cam pins to assemble
back and CPU bay
Insert pins into cabinet holes half way, move
panel into position and push the pins home.
Align the arrows on the cams to point to the
hole for pin insertion. Use a Phillips screw-
driver to tighten cam clockwise a half turn.
CPU Bay bottom
Tighten cam
clockwise
•insertpinshalfway
•putpanelinposition
•pushpinshome
•tightenwithPhillips
screwdriver
•insertpinshalfway
•putpanelinposition
•pushpinshome
•tightenwithPhillips
screwdriver
Cam and pin locations are 3 from side panels to back, and two through back to CPU
Bays. CPU Bay bottoms assemble as shown.

flipIT Lift Desk Assembly ©2015 CBT Supply, Inc. 7 Technical Support: 800-770-7042
Attach L brackets to keyboard
tray and install to desktop
Use self-tapping metal screws
to attach L brackets using the 4th hole, or as desired.
Use 8 kitted wood screws
to install keyboard tray
into pre-drilled pilot holes.
Align the bottom of the monitor enclosure panel
with the bottom of the CPU bay and side panel.
This aligns the Keku clips,
then push the panel home.
Use the pre-drilled pilot holes
to locate the Keku clips.
Install the monitor enclosure panel
Install Male Keku clips on the
monitor enclosure panel.

flipIT Lift Desk Assembly ©2015 CBT Supply, Inc. 8 Technical Support: 800-770-7042
Install lid to
monitor lift
Use supplied wood screws to
install lid bracket to lid.
Install lid assembly
to the top of the
monitor lift mast.
Use Torx T20 driver to install lid
bracket to top of mast.
Push down lid to test function of mechanism.
Push down past the desktop to release mast
to full height.
Torx T20
Install tilter mount
to flipIT lift mast
Use 8/32 Phillips #2 3/8”machine
screws and 3/8”hex nut to install
the tilter mechanism to the mast
at the desired working height of
the monitor.
Install VESA
bracket to monitor
Use the 4M screws supplied with
your monitor to attach the VESA
bracket. Gravity holds the moni-
tor assembly together. Use the
red lever to release the monitor
to dismount.

flipIT Lift Desk Assembly ©2015 CBT Supply, Inc. 9 Technical Support: 800-770-7042
Test the operation of the
flipIT Lift
The flipIT Lift is available for two ranges of monitor
weight.
If you have a heavy monitor on a light lift, the lift may
not bring the monitor to full height without assistance.
If you have a light monitor on a heavy lift, the unit
may be hard to close and raise the monitor faster than
desired.
Models ending in THB are for monitors 15 to 25 lbs. “H”
means Heavy.
Models ending in TLB are for Lighter monitors between
5 and 15 lbs.
Monitor must be in vertical
position for closing
Monitor tilt is not automatic. You must manually set the
monitor position to vertical for opening and closing.
Monitor in stowed position
The monitor can be positioned on any desired vertical
height without fear of hitting the floor when stowed.
The generous wire way from CPU bay to the storage
chamber accommodates cable freedom of movement.
Please make sure that cables have freedom of move-
ment. Remove the front monitor panel for full access.

Does your model have
CPU Bays?
And where do they go?
This assembly instruction booklet does not
illustrate each model, but does show approach
for assembly. Use this page as a guide for how
your finished desk should look.
SFL-362630-X23 SFL-362630-T23
DFL-662630-X23
DFL-722630-T23DFL-722630-C23
www.smartdesks.com
800 770 7042
flipIT Lift Desk®
© 2015 CBT Supply Inc dba SMARTdesks® All rights reserved. SMARTdesks® and flipIT® are registered trademarks of CBT Supply, Inc. rev12042015
One last thing:
(You can do this any time.)
Insert the wire grommets into the 80mm
holes on the desk end panels.