SMARTdesks iLid Touch Installation guide

ASSEMBLY INSTRUCTIONS
Touch
Tables for VESA Mounted Touch Screens and PCs.
Shown with optional EZ Cinch CPU holder, not inlcuded.
Modeled with LCD screens, CPUs, wireless keyboards and mice, not included.
iLid® Tables are available with laminate
tops and PVC edge trim (not shown) and
thrmofoil tops with contoured self edges
(shown).
Design of parts are subject to change.
www.smartdesks.com
800 770 7042
©2018 CBT Supply, Inc. All rights reserved. SMARTdesks® and
iLid® are registered trademarks of CBT Supply, Inc. Designs
are proprietary to CBT Supply, Inc. manufactured for each
customer with customization.

iLid® Table Instructions ©2018 CBT Supply, Inc. 2 Technical Support: 800-770-7042
Parts Identification
Available in thermofoil with contoured self edges
or laminate with PVC edges.
CPU Holders are options.
They mount with a
braket over the
preferred leg, installing
with the hex/phillips
head 1/4-20 bolts. CPU
holders have separate
mounting instructions.
Keyboard storage tray (shown) or retractable dual
arm 26” x 8” keyboard tray installs here with wood
screws.
Modesty panel attaches with wood screws that hang on keyhole
mounts on legs. Neatlinks wire management channels and power
strips install on the modestey panels with wood screws.
The standard iLid top color is black. Thermofoil
designs may be specified to match the top.
This double table shows the laminate treat-
ment with PVC edge trim on top, modestey
panel, and standard, black iLid top. Each iLid
top installs with a set of mounting hinges.
Legs:
iLid® Tables are available in singles with two legs,
doubles with three legs and triples with four legs.
Legs may have 1” adjustable floor glides
(standard) or locking casters (optional).

iLid® Table Instructions ©2018 CBT Supply, Inc. 3 Technical Support: 800-770-7042
Each iLid mounts with a spring-loaded hinge and a passive friction hinge.
Install iLid into
table top
There are two types of hinges
that are mounted in pairs.
Start by mounting the spring
loaded hinge to the lid on
the user’s left side.
The spring will keep the lid in the open position. Use three
Euro Screws to install.
On a padded work surface, place the table top face
down. Put the iLid with springloaded hinge in place.
The spring will need to be tensioned to get the bracket in
this position for installation. Once in place over the pilot
holes, install with Euroscrews.
Next, the passive friction hinge can be installed
with Euroscrews.

iLid® Table Instructions ©2018 CBT Supply, Inc. 4 Technical Support: 800-770-7042
Install VESA bracket
Use three Euro Screws to install the VESA
mount to the iLid. The arangement of pilot
holes give options for placement in 1/2”
increments. The location can be fine tuned
when installing the actual monitor.
If desired, a “dry fit” for installing the monitor
may be performed, so the location might be
determined for the classroom.
The X shaped VESA plate is installed to the
monitor using the screws that come with
the monitor. The X plate is captured into
the bracket installed in the lid. Check to see
if the monitor will clear the opening and
reinstall to the optimum location on the lid
to permit best operation.
TOP OF MONITOR ON EDGE WITH LIP

NeatLinks wire man-
agement channels are
installed flush with the
bottom of the mod-
esty panel, centered
in the user workspace.
Do not rely only on
the adhesive provided
with the NeatLinks because heat, time and weight will cause the
adhesive to release. Install with two self pilot wood screws.
Install the power strip
over the NeatLinks using
long wood screws. Install
such that the wood screws
do not come through
the panel.
iLid® Table Instructions ©2013 CBT Supply, Inc. 5 Technical Support: 800-770-7042
Assemble legs and modesty panel
Fasten the legs using
Phillips/Hex drive 1/4-20
bolts, six per mount-
ing plate. Intall loose to
facilitate mounting the
modesty panel.
Pilot holes are located
on the modesty panel.
Install wood screws
about half way, so they
act as studs
1
2
Keyholes are
located in the legs.
Insert the screw
head studs into the
large end of the
holes and push the
panel up into place.
The loose leg install
lets you have some
wiggle room to
make this easy.
Once the panel is
in place, the screw
heads may be
snugged up through
the holes in the legs.
Then tighten the leg
bolts. Do not over-
torque the bolts, as
doing so might blow
out the inserts.
3

iLid® Table Instructions ©2018 CBT Supply, Inc. 6 Technical Support: 800-770-7042
Install Keyboard tray
Keyboard Tray KB26 has four L brackets that need to be attached
at a uniform depth with the tabs oriented inside. four metal
machine screws are used to fasten the L brackets. This is shown
using the third hole from the bend in the L.
Install the KB26 keyboard tray using eight wood screws,
two per L bracket. Pilot holes are provided that position
the retracted keyboard to be flush with the user edge of the
table. It is easiest to start with the KB26 retracted, installing
the two exposed brackets, then opening the KB26 to permit
access to the front brackets.
KB26 in open position allows access to front L brackets
for installation.
Install Keyboard Stow Tray
The Keyboard stow tray option is installed using the four
wood screws into the pilot holes made for this purpose.

Install monitor and
tension the hinge
iLid™ is tensioned at the factory for a 12-15 lb. monitor. If you
need to make a tension adjustment for smooth operation of
the iLid, use a 5/32”hex key and 7/16”open end wrench to
tighten or loosen the adjustment on the left bracket. The
right bracket has the spring to assist opening. The friction
adjustment of the left bracket provides damping so the lid
doesn’t open with too much force and bounce the monitor
around.
You will need to remove the monitor to make this adjustment. Be careful when opening the iLid
without a monitor installed. If the spring tension does not have any friction resistance, the lid
will open too fast and the forces could tear the lid from the mounting screws. If this happens,
use a wooden toothpick and wood glue to repair the mounting hole.
Finishing the installation
Put the table on the floor on its feet or casters. If you installed a CPU
holder, such as the EZ Cinch or Brig, the bracket for this has been
installed over the leg bracket. The CPU can be installed according to
the directions that came with the CPU holder.
iLid® Table Instructions ©2018 CBT Supply, Inc. 7 Technical Support: 800-770-7042