SMB Modulus 90 Manual

Technical Information
Trampoline “modulus 90”
page 1
Installation instructions EN 1176-1
Maintenance instructions EN 1176-1
03.04.2018
General
The work described must be carried out by a qualified person.
Due to the heavy weight of the completed trampoline, no further anchorage is necessary.
The trampoline is designed to build levelled with the ground.
Dimensions
Overall size: see draft plan
Minimum space: see draft plan
Jumping area: 1,37m²
Clearance: 1,50 m
Max. free fall height: 0,90 m
Age group
3 years and up
Number of users
1 person
Ground conditions
Please refer to DIN EN 1176-1 for ground conditions in the play area.
We recommend synthetic fall protection, as loose fall protection material like sand, bark mulch or
wood chips can fall easily into the trampoline and thus minimize the play value.
Installation tools –tools supplied
6 pieces support iron rings
1 piece Tool to assemble and/or remove jumping mats
Example Picture: Trampolin „modulus 90“ traffic orange
BUNTE HÜPFER
colortramp®
Artikelno. 7232001-E

Technical Information smb
Trampoline “modulus 90”Seilspielgeräte GmbH Berlin
page 2 Technikerstraße 6/8
15366 Hoppegarten
Telefon [phone]
Telefax (0 33 42) 5 08 37 80
Assembly
The trampoline is erected after the ground has been excavated (450 mm deep, size according to number of
trampolines) and an even horizontal surface has been created. If there is a bad soil situation (e.g. loamy soil)
we recommend a drainage layer.
Boreholes (sealed with plugs), which are for the six supporting iron rings supplied, are located on the
sides of the frame. Please make sure to close these boreholes again! It has to be ensured that the
framework is lying snug and does not wobble. This can be checked simply by standing on it. The play
area around the trampoline has to be refilled appropriately.
Image 2

Technical Information smb
Trampoline “modulus 90”Seilspielgeräte GmbH Berlin
page 3 Technikerstraße 6/8
15366 Hoppegarten
Telefon [phone]
Telefax (0 33 42) 5 08 37 80
Assembly and removal of the jumping mat
The trampoline is supplied with a suspended jumping mat in the frame. The jumping mat only needs to be
removed when damaged or when the trampoline is cleaned.
Removal of the jumping mat
Using the tool supplied, the springs can be loosened from the suspended mat from the top (image 3).To
do this, the hock is suspended in the eye of the tension spring which opens from the bottom and slowly
pulled onto the rope which is fastened onto the hook. If the spring extends enough, then the eye, which is
suspended on the jumping mat, falls down automatically. It is the same procedure for the side of the
thimble (image 2).
Assembly of the jumping mat
When assembling the jumping mat, make sure that the sides of the mat with the chains (image 3) face
towards the straight side (image 2).
longitudinal direction: connection thimble
cross direction: connection chains
1) tighten the spring 2) clip the spring into the eye 3) release the spring
Image 3

Technical Information smb
Trampoline “modulus 90”Seilspielgeräte GmbH Berlin
page 4 Technikerstraße 6/8
15366 Hoppegarten
Telefon [phone]
Telefax (0 33 42) 5 08 37 80
Maintenance instructions EN 1176-1
Routine visual inspection
The frequency of this inspection depends on local conditions (high/low usage, vandalism, air
contamination, effects of the weather).
Operational inspection (every 6 months)
Check unit for general damage or wear and tear.
Check condition of the jumping mat, spring suspensions and protective panels.
Main inspection
The trampoline framework consists of galvanised sheets, 3 mm thick. Due to this fact, a main inspection,
which then includes checking the framework for corrosion, only needs to be carried out every two years.
Type Plate Location
The type plate is located in one of the rubber tiles, which are glued on the trampoline steel frame. On the
type plate you will find details to the manufacturer, the DIN-Norm, a serial number and also a QR-Code
for furthermore information.