ROSE DISPLAYS ANOGOTCHA ROUND WITH MULTICLIPS User manual

Parts
OneUp Instruction Sheet
AnoGotcha™
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Squeeze sides of MultiClip together. Fig. 2
Step 3
Align the bottom rail of the MultiClip with
the top channel of the aluminum holder.
Slide MultiClip into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). Insert graphic
completely into holder until edge of graphic
meets top of holder. To close, snap the
AnoGotcha Holder shut. Fig. 5
Note: It is easier to open and close the
Gotcha by starting at one end and working
your way down the holder. With large or
curling graphics, it may be easier to insert
graphic at one end and slide into holder from
one end to another.
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha Holder,
End Caps and MultiClips for future projects.
Instructions for Hanging
Incept-7.31.02
AnoGotcha™is a trademark and Gotcha®is a registered trademark of Rose
Displays, Ltd. Neither the manufacturer nor any sales agent may be held
liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaMC
Figure 1
Figure 3 Figure 4
Figure 5
Figure 6
End Caps
06-5525
MultiClip
1UP-0101
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 2

Parts
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Squeeze sides of MultiClip together. Fig. 2
Step 3
Align the bottom rail of the MultiClip with
the top channel of the aluminum holder.
Slide MultiClip into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). Insert graphic
completely into holder until edge of graphic
meets top of holder. To close, snap the
AnoGotcha Holder shut. Fig. 5
Note: It is easier to open and close the
Gotcha by starting at one end and working
your way down the holder. With large or
curling graphics, it may be easier to insert
graphic at one end and slide into holder from
one end to another.
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha Holder,
End Caps and MultiClips for future projects.
Instructions for Hanging
Incept-7.31.02
AnoGotcha™is a trademark and Gotcha®is a registered trademark of Rose
Displays, Ltd. Neither the manufacturer nor any sales agent may be held
liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaMC
End Caps
06-5525
MultiClip
1UP-0101
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Figure 1
Figure 3 Figure 4
Figure 5
Figure 6
Figure 2
OneUp Instruction Sheet
AnoGotcha™

Parts
Instructions for Hanging
Incept-7.31.02
AnoGotcha™is a trademark and Gotcha®is a registered trademark of Rose
Displays, Ltd. Neither the manufacturer nor any sales agent may be held
liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaMC
End Caps
06-5525
MultiClips
1UP-0101
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
Instruction Sheet
AnoGotcha™
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Squeeze sides of MultiClip together. Fig. 2
Step 3
Align the bottom rail of the MultiClip with
the top channel of the aluminum holder.
Slide MultiClip into rail. Fig. 3 Repeat
steps 2 and 3 for second MultiClip
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). Insert graphic
completely into holder until edge of graphic
meets top of holder. To close, snap the
AnoGotcha Holder shut. Fig. 5
Note: It is easier to open and close the
Gotcha by starting at one end and working
your way down the holder. With large or
curling graphics, it may be easier to insert
graphic at one end and slide into holder from
one end to another.
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha Holder,
End Caps and MultiClips for future projects.

Parts
Instructions for Hanging
Incept-7.31.02
AnoGotcha™is a trademark and Gotcha®is a registered trademark of Rose
Displays, Ltd. Neither the manufacturer nor any sales agent may be held
liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaMC
End Caps
06-5525
MultiClips
1UP-0101
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
Instruction Sheet
AnoGotcha™
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Squeeze sides of MultiClip together. Fig. 2
Step 3
Align the bottom rail of the MultiClip with
the top channel of the aluminum holder.
Slide MultiClip into rail. Fig. 3 Repeat
steps 2 and 3 for second MultiClip
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). Insert graphic
completely into holder until edge of graphic
meets top of holder. To close, snap the
AnoGotcha Holder shut. Fig. 5
Note: It is easier to open and close the
Gotcha by starting at one end and working
your way down the holder. With large or
curling graphics, it may be easier to insert
graphic at one end and slide into holder from
one end to another.
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha Holder,
End Caps and MultiClips for future projects.