SMC Networks GS5 FICHE User manual

EZ Switch 10/100/1000
User Guide
From SMC’s EZ line of low-cost workgroup LAN solutions
May 2005
Pub #: 150000018400H R01
38 Tesla
Irvine, CA 92618
Phone: [phone]

Copyright
Information furnished by SMC Networks, Inc. (SMC) is believed to be
accurate and reliable. However, no responsibility is assumed by SMC for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of SMC. SMC reserves the right
to change specifications at any time without notice.
Copyright © 2005 by
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
All rights reserved. Printed in Taiwan
Trademarks:
SMC is a registered trademark; and EZ Connect is a trademark of SMC Networks,
Inc. Other product and company names are trademarks or registered trademarks of
their respective holders.

L IMITED W ARRANTY
Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to
be free from defects in workmanship and materials, under normal use and service, for
the applicable warranty term. All SMC products carry a standard 90-day limited
warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at
its own discretion, repair or replace any product not operating as warranted with a
similar or functionally equivalent product, during the applicable warranty term. SMC
will endeavor to repair or replace any product returned under warranty within 30 days
of receipt of the product.
The standard limited warranty can be upgraded to a Limited Lifetime* warranty by
registering new products within 30 days of purchase from SMC or its Authorized
Reseller. Registration can be accomplished via the enclosed product registration card
or online via the SMC web site. Failure to register will not affect the standard limited
warranty. The Limited Lifetime warranty covers a product during the Life of that
Product, which is defined as the period of time during which the product is an
“Active” SMC product. A product is considered to be “Active” while it is listed on the
current SMC price list. As new technologies emerge, older technologies become
obsolete and SMC will, at its discretion, replace an older product in its product line
with one that incorporates these newer technologies. At that point, the obsolete
product is discontinued and is no longer an “Active” SMC product. A list of
discontinued products with their respective dates of discontinuance can be found at:
http://www.smc.com/index.cfm?action=customer_service_warranty
All products that are replaced become the property of SMC. Replacement products
may be either new or reconditioned. Any replaced or repaired product carries either a
30-day limited warranty or the remainder of the initial warranty, whichever
is longer.
SMC is not responsible for any custom software or firmware, configuration
information, or memory data of Customer contained in, stored on, or integrated with
any products returned to SMC pursuant to any warranty. Products returned to SMC
should have any customer-installed accessory or add-on components, such as
expansion modules, removed prior to returning the product for replacement. SMC is
not responsible for these items if they are returned with the product.
Customers must contact SMC for a Return Material Authorization number prior to
returning any product to SMC. Proof of purchase may be required. Any product
returned to SMC without a valid Return Material Authorization (RMA) number clearly
marked on the outside of the package will be returned to customer at customer's
expense. For warranty claims within North America, please call our toll-free customer
support number at [phone]. Customers are responsible for all shipping charges
from their facility to SMC. SMC is responsible for return shipping charges from SMC
to customer.
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE
AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR
OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION.
THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND
ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS
OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY
OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO
ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE
SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC
SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT
DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD

PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING,
UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE
BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE,
LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN
CONTRACT OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE
LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR
PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS
OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN
IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED
WARRANTIES OR THE LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE
ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY
VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE
TAKEN TO AFFECT YOUR STATUTORY RIGHTS.
* SMC will provide warranty service for one year following discontinuance from the
active SMC price list. Under the limited lifetime warranty, internal and external power
supplies, fans, and cables are covered by a standard one-year warranty from date of
purchase.
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618

C OMPLIANCES
FCC - Class B
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that the interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
EC Conformance Declaration - Class B
SMC contact for these products in Europe is:
SMC Networks Europe,
Edificio Conata II,
Calle Fructuós Gelabert 6-8, 2
o
, 4
a
,
08970 - Sant Joan Despí,
Barcelona, Spain.
This information technology equipment complies with the
requirements of the Council Directive 89/336/EEC on the
Approximation of the laws of the Member States relating to
Electromagnetic Compatibility and 73/23/EEC for electrical
equipment used within certain voltage limits and the Amendment
Directive 93/68/EEC. For the evaluation of the compliance with
these Directives, the following standards were applied:
RFI Emission:
•Limit class A according to EN55022:1998
•Limit class A for harmonic current emission
according to EN61000-3-2/1995
•Limitation of voltage fluctuation and flicker in
low-voltage supply system according to
EN61000-3-3/1995

Industry Canada - Class B
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus as set out in the
interference-causing equipment standard entitled “Digital Apparatus,”
ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques
applicables aux appareils numériques de Classe A prescrites dans la
norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003
édictée par le ministère des Communications.
Immunity:
•Product family standard according to
EN55024:1998
•Electrostatic Discharge according to
EN61000-4-2:1995 (ContactDischarge: ±4
kV, Air Discharge: ±8 kV)
•Radio-frequency electromagnetic field
according to EN61000-4-3:1996 (80 - 1000
MHz with 1 kHz AM 80% Modulation: 3 V/m)
•Electrical fast transient/burst according to
EN61000-4-4:1995 (AC/DC power supply:
±1 kV, Data/Signal lines: ±0.5 kV)
•Surge immunity test according to
EN61000-4-5:1995
(AC/DC Line to Line: ±1 kV, AC/DC Line to
Earth: ±2 kV)
•Immunity to conducted disturbances, Induced
by radio-frequency fields: EN61000-4-6:1996
(0.15 - 80 MHz with
1 kHz AM 80% Modulation: 3 V/m)
•Power frequency magnetic field immunity test
according to EN61000-4-8:1993 (1 A/m at
frequency 50 Hz)
•Voltage dips, short interruptions and voltage
variations immunity test according to
EN61000-4-11:1994 (>95% Reduction @10
ms, 30% Reduction @500 ms, >95%
Reduction @5000 ms)
LVD: •EN 60950-1

Please read the following safety informa-
tion carefully before installing the
Switch:
WARNING: Installation and removal of the unit must be
carried out by qualified personnel only.
•This guide is intended for use by network
administrators who are responsible for setting up and
installing network equipment; consequently it assumes
a basic working knowledge of LANs (Local Area
Networks).
•The unit must be connected to an earthed (grounded)
outlet to comply with international safety standards.
•Do not connect the unit to an A.C. outlet (power
supply) without an earth (ground) connection.
•The appliance coupler (the connector to the unit and
not the wall plug) must have a configuration for mating
with an EN 60320/IEC 320 appliance inlet.
•The socket outlet must be near to the unit and easily
accessible. You can only remove power from the unit
by disconnecting the power cord from the outlet.
•This unit operates under SELV (Safety Extra Low
Voltage) conditions according to IEC 60950. The
conditions are only maintained if the equipment to
which it is connected also operates under SELV
conditions.

France and Peru only
This unit cannot be powered from IT†supplies. If your supplies are
of IT type, this unit must be powered by 230 V (2P+T) via an iso-
lation transformer ratio 1:1, with the secondary connection point
labelled Neutral, connected directly to earth (ground).
†Impédance à la terre
Power Cord Set
U.S.A. and
Canada The cord set must be UL-approved and CSA certified.
The minimum specifications for the flexible
cord are:
- No. 18 AWG - not longer than 2 meters, or
16 AWG.
- Type SV or SJ
- 3-conductor
The cord set must have a rated current ca-
pacity of at least 10 A.
The attachment plug must be an
earth-grounding type with NEMA 5-15P (15
A, 125 V) or NEMA 6-15P (15 A, 250 V)
configuration.
Denmark The supply plug must comply with Section
107-2-D1, Standard DK2-1a or DK2-5a.
Switzerland The supply plug must comply with SEV/
ASE 1011.
U.K. The supply plug must comply with BS1363
(3-pin 13 A) and be fitted with a 5 A fuse
which complies with BS1362.
The mains cord must be <HAR> or
<BASEC> marked and be of type
HO3VVF3GO.75 (minimum).
Europe The supply plug must comply with CEE7/7
(“SCHUKO”).
The mains cord must be <HAR> or
<BASEC> marked and be of type
HO3VVF3GO.75 (minimum).
IEC-320 receptacle.

Veuillez lire à fond l'information de la
sécurité suivante avant d'installer le
Switch:
AVERTISSEMENT: L’installation et la dépose de ce
groupe doivent être confiés à un personnel qualifié.
•Ne branchez pas votre appareil sur une prise secteur
(alimentation électrique) lorsqu'il n'y a pas de
connexion de mise à la terre (mise à la masse).
•Vous devez raccorder ce groupe à une sortie mise à la
terre (mise à la masse) afin de respecter les normes
internationales de sécurité.
•Le coupleur d’appareil (le connecteur du groupe et non
pas la prise murale) doit respecter une configuration
qui permet un branchement sur une entrée d’appareil
EN 60320/IEC 320.
•La prise secteur doit se trouver à proximité de l’appareil
et son accès doit être facile. Vous ne pouvez mettre
l’appareil hors circuit qu’en débranchant son cordon
électrique au niveau de cette prise.
•L’appareilfonctionneàunetensionextrêmementbasse
de sécurité qui est conforme à la norme IEC 60950.
Ces conditions ne sont maintenues que si l’équipement
auquel il est raccordé fonctionne dans les mêmes
conditions.
France et Pérou uniquement:
Ce groupe ne peut pas être alimenté par un dispositif à impédance
à la terre. Si vos alimentations sont du type impédance à la terre, ce
groupe doit être alimenté par une tension de 230 V (2 P+T) par le
biais d’un transformateur d’isolement à rapport 1:1, avec un point
secondaire de connexion portant l’appellation Neutre et avec rac-
cordement direct à la terre (masse).

Bitte unbedingt vor dem Einbauen des
RPU die folgenden
Sicherheitsanweisungen durchlesen:
WARNUNG: Die Installation und der Ausbau des Geräts
darf nur durch Fachpersonal erfolgen.
•Diese Anleitung ist fr die Benutzung durch
Netzwerkadministratoren vorgesehen, die fr die
Installation und das einstellen von
Netzwerkkomponenten verantwortlich sind; sie setzt
Erfahrung bei der Arbeit mit LANs (Local Area
Networks) voraus.
Cordon électrique - Il doit être agréé dans le pays d’utilisation
Etats-Unis et Canada: Le cordon doit avoir reçu l’homolo-
gation des UL et un certificat de la
CSA.
Lesspe'cificationsminimalespourun
cable flexible sont AWG No. 18,
ouAWG No. 16 pour un cable de
longueur infe'rieure a` 2 me'tres.
- type SV ou SJ
- 3 conducteurs
Le cordon doit être en mesure
d’acheminer un courant nominal d’au
moins 10 A.
La prise femelle de branchement doit
être du type à mise à la terre (mise à
la masse) et respecter la configuration
NEMA 5-15P (15 A, 125 V) ou
NEMA 6-15P (15 A, 250 V).
Danemark: La prise mâle d’alimentation doit re-
specter la section 107-2 D1 de la
norme DK2 1a ou DK2 5a.
Suisse: La prise mâle d’alimentation doit re-
specter la norme SEV/ASE 1011.
Europe La prise secteur doit être conforme
aux normes CEE 7/7 (“SCHUKO”)
LE cordon secteur doit porter la
mention <HAR> ou <BASEC> et
doit être de type HO3VVF3GO.75
(minimum).

•Das Gerät sollte nicht an eine ungeerdete
Wechselstromsteckdose angeschlossen werden.
•Das Gerät muß an eine geerdete Steckdose
angeschlossen werden, welche die internationalen
Sicherheitsnormen erfüllt.
•Der Gerätestecker (der Anschluß an das Gerät, nicht
der Wandsteckdosenstecker) muß einen gemäß EN
60320/IEC 320 konfigurierten Geräteeingang haben.
•Die Netzsteckdose muß in der Nähe des Geräts und
leicht zugänglich sein. Die Stromversorgung des
Geräts kann nur durch Herausziehen des
Gerätenetzkabels aus der Netzsteckdose unterbrochen
werden.
•Der Betrieb dieses Geräts erfolgt unter den
SELV-Bedingungen (Sicherheitskleinstspannung)
gemäß IEC 60950. Diese Bedingungen sind nur
gegeben, wenn auch die an das Gerät angeschlossenen
Geräte unter SELV-Bedingungen betrieben werden
Stromkabel. Dies muss von dem Land, in dem es benutzt wird
geprüft werden:
Schweiz Dieser Stromstecker muß die SEV/ASE
1011Bestimmungen einhalten.
Europe Das Netzkabel muß vom Typ
HO3VVF3GO.75 (Mindestanforderung) sein
und die Aufschrift <HAR> oder <BASEC>
tragen.
Der Netzstecker muß die Norm CEE 7/7 er-
füllen (”SCHUKO”).

Warnings and Cautionary Messages
Warnings (in German)
Warning: This product does not contain any user serviceable
parts.
Warning: Installation and removal of the unit must be carried
out by qualified personnel only.
Warning: When connecting this device to a power outlet,
connect the field ground lead on the tri-pole power
plug to a valid earth ground line to prevent electrical
hazards.
Warning: This product uses lasers to transmit signals over fiber
optic cable. The lasers are compliant with the
requirements of a Class 1 Laser Product and are
inherently eye safe in normal operation. However, you
should never look directly at a transmit port when it is
powered on.
Caution: Wear an anti-static wrist strap or take other suitable
measures to prevent electrostatic discharge when
handling this equipment.
Caution: Do not plug a phone jack connector in the RJ-45 port.
This may damage this device. Les raccordeurs ne sont
pas utilisé pour le système téléphonique!
Caution: Use only twisted-pair cables with RJ-45 connectors
that conform to FCC standards.
Achtung: Dieses Produkt enthält keine Teile, die eine Wartung
vom Benutzer benötigen.
Achtung: Installation und Deinstallation des Gerätes müssen von
qualifiziertem Servicepersonal durchgeführt werden.
Achtung: Wenn das Gerät an eine Steckdose angeschlossen wird,
muß der Masseanschluß am dreipoligen Netzstecker
mit Schutzerde verbunden werden, um elektrische
Gefahren zu vermeiden.
Achtung: Dieses Gerät nutzt Laser zur Signalübertragung über
Glasfasern. Die Laser entsprechen den Anforderungen
an eine Lasereinrichtung der Klasse 1 und sind durch
ihre Bauart im normalen Betrieb sicher für die Augen.
Trotzdem sollte niemals direkt in den einen
Übertragungskanal geblickt werden, wenn er
eingeschaltet ist.

Environmental Statement
The manufacturer of this product endeavours to sustain an
environmentally-friendly policy throughout the entire production
process. This is achieved though the following means:
•Adherence to national legislation and regulations on
environmental production standards.
•Conservation of operational resources.
•Waste reduction and safe disposal of all harmful un-recyclable
by-products.
•Recycling of all reusable waste content.
•Design of products to maximize recyclables at the end of the
product’s life span.
•Continual monitoring of safety standards.
End of Product Life Span
This product is manufactured in such a way as to allow for the
recovery and disposal of all included electrical components once the
product has reached the end of its life.
Manufacturing Materials
There are no hazardous nor ozone-depleting materials in this product.
Documentation
All printed documentation for this product uses biodegradable paper
that originates from sustained and managed forests. The inks used in
the printing process are non-toxic.
Purpose
This guide details the hardware features of the switch, including Its
physical and performance-related characteristics, and how to install the
switch.
Audience
The guide is intended for use by network administrators who are
responsible for installing and setting up network equipment;
consequently, it assumes a basic working knowledge of LANs (Local
Area Networks).
Diese Anleitung ist f
ü r die Benutzung durch Netzwerkadministratoren
vorgesehen, die f
ü r die Installation und das einstellen von
Netzwerkkomponenten verantwortlich sind; sie setzt Erfahrung bei
der Arbeit mit LANs (Local Area Networks) voraus.

Safety Compliance
Underwriters Laboratories Compliance State-
ment
Important! Before making connections, make sure you have the
correct cord set. Check it (read the label on the cable) against the
following:
The unit automatically matches the connected input voltage.
Therefore, no additional adjustments are necessary when connecting it
to any input voltage within the range marked on the rear panel..
Operating Voltage Cord Set Specifications
120 Volts UL Listed/CSA Certified Cord Set
Minimum 18 AWG
Type SVT or SJT three conductor
cord
Maximum length of 15 feet
Parallel blade, grounding type
attachment plug rated 15 A, 125 V
240 Volts (Europe only) Cord Set with H05VV-F cord
having three conductors with
minimum diameter of 0.75 mm2
IEC-320 receptacle
Male plug rated 10 A, 250 V

Contents
INTRODUCTION 1
Description of Hardware 1
Features and Benefits 1
Front Panel RJ-45 Ports 2
SMCGS5 Front and Rear Panels 3
SMCGS8 Front and Rear Panels 4
Rear Panel 4
INSTALLING THE SWITCH 5
Package Checklist 5
Selecting a Site 5
Instructions 6
APPLICATION EXAMPLE 8
TROUBLESHOOTING 9
SPECIFICATIONS 10

EZ Switch 10/100/1000
1
INTRODUCTION
The EZ Switch 10/100/1000, SMCGS5 and SMCGS8, are
high-performance Gigabit Ethernet switches designed for
delivering Gigabit connectivity to the desktop. It provides
5/8 full-duplex 1000BASE-T ports that significantly
improve network performance and boost throughput for
high-bandwidth applications. With 10/16 Gigabits of
aggregate bandwidth, this switch provides the quickest
solution to meeting the growing demands on your
network's limited resources.
Features and Benefits
•Auto-negotiation supported on all ports
•Automatic MDI/MDI-X operation
•IEEE 802.3ab, 802.3u, and 802.3 compliance ensures
compatibility with standards-based hubs, switches and
cards from any vendor
•Store-and-forward switching ensures error-free
transmission
•Half- and full-duplex flow control prevents packets
from being dropped under heavy loading
•Plug-and-play-nothing to configure
•"At-a-glance" LEDs for port and system status
monitoring
•Desktop installation
Front Panel RJ-45 Ports
The EZ Switch 10/100/1000 features 5/8 1000BASE-T
ports with RJ-45 connectors located on the front panel of
the switch. Because all ports support automatic MDI/
MDI-X operation, you can use straight-through cables for
all network connections to PCs or servers, or to other
switches or hubs.

EZ Switch 10/100/1000
2
Front Panel LEDs
The front panel of the switch provides status LEDs for
“at-a-glance” system monitoring. The following table
details the functions of the various indicators.
SMCGS5 Front and Rear Panels
Port and System Status LEDs
LED Condition Status
Power On Power on, normal operation.
Off Power off or failure.
Link/Act On(Green) Network device is correctly
connected to the switch
through this port.
Off No link.
Flashing
(Green) Data is being sent or received through this port.
1000M On(Green) Connected at 1000M.
Off Connected at 10 or 100M.

EZ Switch 10/100/1000
3
SMCGS8 Front and Rear Panels
Rear Panel
The DC power socket is located on the rear panel of the
switch.