Smith & Noble Euro Track Basics Hardware - Heavy Duty User manual

STEP BY STEP INSTALLATION INSTRUCTIONS
Wall Mount
Double Rod Set
Euro Track
Basics Hardware -
Heavy Duty

2
800.248.8888
1smithandnoble.com
A Smooth Set-Up
We want you to love your new hardware and that includes
having a smooth installation experience. We suggest saving
        
please reach out to us for help. It’s why we’re here. Call us at
800.248.8888 for more info on installation.
We recommend you hold on to all packaging until your
hardware is fully installed. Should something go wrong (we
          
painless as possible.
Customer Service Hours
Monday — Friday: 6am — 6pm PT
Saturday — Sunday: 7am — 4pm PT
smithandnoble.com
Everything
You Need
Table of Contents
Step 1 - Getting Started ..................................3
Overview - Wall Mount Double Rod Set.......................4
Step 2 - Mounting the Brackets ........................ 5 - 6
Step 3 - Attaching the Rod Connector......................7
Step 4 - Adding or Removing Carriers & End Stops ......8 - 10
Step 5 - Attaching Bracket Posts..........................11
Step 6 - Attaching the Finials ............................12
Step 7 - Attaching Back Rod Clips ........................13
Step 8 - Attaching Bracket Posts to Bracket Bases ..........14
Step 9 - Attaching Back Rod .............................15
Step 10 - Attaching Drapery to Rod ........................16
Accessories - Baton/Wand ..................................17
Care & Cleaning ...........................................18
Warranty ..........................................Back Cover

34
smithandnoble.com 800.248.8888
STEP 1 - GETTING STARTED OVERVIEW

need. You’ll need to make sure the surface you intend to install your hardware is sturdy enough
to accommodate the brackets. If you’re screwing directly into a surface this means locating

you’ll need to use a secure fastener (as illustrated) but please note this piece is not included.
Tools & Parts
WALLBOARD OR PLASTER:
Hollow wall applications: Use a secure fastener designed

METAL:
Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE:



the fastener manufacturer’s instructions regarding proper installation.
TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE:
764
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the
screws are too tight this may cause the screw itself to break off in the wall or window frame.
MOLLY
BOLT
SELF DRILLING
ANCHOR
TOGGLE
BOLT
Euro Track Basics Heavy Duty Wall Mount Double Rod Set
SCREWS MOUNTING CLIPS END & CENTER BRACKET
PENCIL
(NOT INCLUDED)
BACK ONLY
ROD
FRONT OR
BACK ROD
CARRIERS CENTER SPLICER BRACKET
SCREWDRIVER
(NOT INCLUDED)
POWER DRILL
(NOT INCLUDED)
LEVEL
(NOT INCLUDED)
ROD QTY BRACKET QTY ROD WIDTH
2 2 
2 3 8
4 4 8
4 5 8
4 7 8
4 7 8
6 9 8
611 8
613 8
813 8
FINIAL
ROD
MOUNTING
BRACKET
MASTER
CARRIER CARRIERS

56
smithandnoble.com 800.248.8888
Place the panel on the rod. To ensure
      
it up to the spot you wish to install
it; this will allow you to raise or lower
your treatment as desired.
After you’ve located the ideal

where the top of the rod is resting.
Remove the panel from the rod and
then center the rod over the window
opening at the desired height. Using
      
each rod are positioned; if you’re
     
middle point between these two
spots as well. If you have more than
one center bracket spread these
evenly between the two end brackets
and center point. If you have a spliced
rod, mark where that splice is as well
on the wall since you will need to add
the special splice bracket at that point
as well. Measure 6” inward from the
marks you’ve made on both ends
and mark those spots. This is where
the end brackets will be installed.
Place center of bracket cover plate
level against wall at the marked spots.
      
around the base of the bracket onto
 (see Figure A). Check to make
sure the circles are level & aligned
with each other.
Remove back plate and center it
inside of the circle outline on wall.
Mark the screw hole locations for all
brackets (see Figure B).
Attach the metal back plate to the

with the marks made in the previous
step (see Figure B). Be sure and
attach the plate to the wall with the
appropriate mounting hardware.
(It is always recommended to try
and attach to the wood studs inside
the wall. Where this is not possible
please use a wall anchor suitable to
carry the weight of your hardware
selection as well as your draperies
and any accessories.)
Place bracket cover plate on top of
back plate and thread on the post.
Make sure to screw on the post very
tightly. Do not leave any play or
wiggle room.
STEP 2 - MOUNTING BRACKETS STEP 2 - MOUNTING BRACKETS
FIGURE B
Mark all holes needed
showing locations of screw
holes for all brackets.
BACK PLATE
FIGURE A
BACK PLATE
BRACKET
COVER PLATE
INNER
POST
OUTER
POST
SET SCREW
CENTER
BOLT
Splice Bracket
End & Center Brackets
BRACKET
BRACKET
COVER PLATE
INNER
POST
OUTER
POST
SET SCREW
CENTER
BOLT
CENTER ROD 6"
BOLT

78
smithandnoble.com 800.248.8888
Front Rod
Your track rod will come with all master
carriers and regular carriers pre-
installed.
If you need to add or take out some

unscrew the End Cap from the rod.
Remove the carrier & end stop and
either add or take out the carriers
needed.
SPLIT DRAPERY (A)
Once all carriers have been placed in


each end and the second carrier so
end of drape does not move when
drape is closed.
ONE WAY DRAW DRAPERY (B)
     
end stop in between the first carrier
from the end and the second carrier
of the side you won’t be opening it
from so the end of drape does not
move when drape is closed.
Place another end stop right before
the beginning of the end cap to
prevent the master carrier from
moving all the way to the end.
STEP 3 - ATTACHING THE ROD CONNECTOR STEP 4 - ADDING OR REMOVING CARRIERS
END STOP
BACK
CARRIERS ONLY FRONT OR BACK CARRIERS
ROD
CONNECTOR
ROD CONNECTER
ROD
SPLICER
FIGURE A
FIGURE B
ROD SPLICER
     
have received a rod connector.
A rod connector is the short piece of
metal placed inside each end of the
rods in a multi-segment system to
join them together.
     (see figure
A),(see figure
B).
Join track sections together and
fasten securely with set screws.
Attach mounting clip at splice by
pressing clip down and snapping it
(see figure C).
A) Split Draw
End stop & Carrier positions
END STOP END CAP
FRONT ROD
FINIAL
MASTER CARRIER
ROD
B) One Way Draw
End stop & Carrier positions
END STOP END CAPMASTER CARRIER
FRONT ROD
FINIAL
ROD
CARRIER
FRONT ROD
FINIAL
ROD
END
CAP
FIGURE C
ROD
SPLICE
MOUNTING
CLIP