Smith & Noble Eco-Wood Shutters User manual
Deco Frame, L-Frame, Z-Frame, Direct Mount
and Hang Strips
Eco-Wood Shutters
STEP BY STEP INSTALLATION INSTRUCTIONS
12
smithandnoble.com 800.248.8888
A Smooth Set-Up
We want you to love your new hardware and that includes having
800.248.8888
Customer Service Hours
Monday — Friday: 6am — 6pm PT
Saturday — Sunday: 7am — 4pm PT
Everything
You Need
TABLE OF CONTENTS
Deco Frame
3
4
5
6 - 7
8
9
4-Sided L Frame
10
11
12
13
14
15
16
4-Sided Z Frame
17
18
19
20 - 21
22 - 23
24
25
26
Direct Mount Install ..............................................................................27
Hang Strip Install....................................................................................31
Warranty
34
smithandnoble.com 800.248.8888
Tools & Parts
Pencil, ¼" nut driver, level, and a drill with a 116
A
•
•
•
•
A A
screwdriver to separate
provided in hardware
Assemble the Frame
Tip: Place the filler strips away from the work area
but in the vicinity of the matching frame.
Tip: Hoffman Keys have a flat & rounded side.
The rounded side goes in facing up.
56
smithandnoble.com 800.248.8888
Tools & Parts
Pencil, ¼" nut driver, level, and a drill with a 116
A
•
•
•
•
A A
Installing T-Posts
Line up the pre-drilled holes with the
Tip: It is recommended to use a 6” extension to
avoid damaging the face of the Deco frame.
evenly around the window opening
screw into the top LEFT
one nail into the top LEFT
Tip: The 5/8” light block of the frame is designed
to sit inside the window opening.
Leveling the Frame
screw into the top
one nail into the top
SECURED, PANELS CAN BE INSTALLED.
NOTE: If not installing a T-POST skip to Leveling the Frame.
78
smithandnoble.com 800.248.8888
Assemble the Frame(s)
TIP: The Hoffman Key has a rounded and a flat
side to it. The rounded side goes in face up.
Installing T-Posts
the pre-drilled holes with the top
All L Frame T-Post installations are
NOTE: If not installing a T-POST skip to Leveling the Frame.
910
smithandnoble.com 800.248.8888
Install Shutter Panels
Installing the Frame
TIP: It is best to angle the drill gun or nail
gun to ensure contact with a stud around the
window opening.
Leveling the Frame
screw into the top
one nail into the top
can be installed.
A
B
A
B
Adjust Positioning
should
secured with the hinge pins, make
sure shutter panel is even across the
11 12
smithandnoble.com 800.248.8888
Secure Frames
TIP: With the bottom right secured, step away
from the window and open louvers to make sure
shutter is evenly positioned to window.
FRAME
FRAME
FRAME
FRAME
Check Spacing
Install Hinge Spacers (if needed)
Tighten the screws and the spacer
Check Operation
Now that you have secured the top
TIP: Move top and bottom frames up and down
to achieve proper tolerance between panel and
frame.
TIP: Move side frame in and out to achieve proper
tolerance between panel and frame.
13 14
smithandnoble.com 800.248.8888
Tools & Parts
116
A
•
•
•
•
A A
Assemble Frame(s)
TIP: The Hoffman Key has a rounded and a flat
side to it. The rounded side goes in face up.
corners to complete the 4 sided
15 16
smithandnoble.com 800.248.8888
Installing T-Posts
Line up the pre-drilled holes with the
All Z-Frame T-Post installations are
Installing the Frame
Tip: Use a counter sink bit for best
results.
FRAME
FRAME
17 18
smithandnoble.com 800.248.8888
Installing the Frame
only
only
Level and Install Frame
19 20
smithandnoble.com 800.248.8888
Install the Shutter Panels
Place the LEFT shutter panel in the
and close other panel to hold it in
Adjust Positioning
and secured with the hinge pins,
make sure shutter panels are even
Installing the Bottom Frame
only
only
LEFT SHUTTER PANEL
TIP: Step away from the window and open louvers
to make sure shutter is evenly positioned in window.
Things to look for: Align window
mullions and/or sectioned glass with
shutter lines (louver, stiles).
21 22
smithandnoble.com 800.248.8888
only
screw into the
only
nail into the
TIP: Move top & bottom frame up and down to
achieve proper tolerance between panel and frame.
TIP: Move side frames in and out to achieve proper
tolerance between panel and frame.
are secured, check that the shutter
TIP: It is recommended to apply 2 nails or screws
for every hinge, and 1 nail or screw between hinges.
GAP
Frame
Top
Frame
23 24
smithandnoble.com 800.248.8888
Tools & Parts
Pencil, ¼" nut driver, level, and a drill with a 116
•
•
•
•
Panel in the window
Installing the Left Hinge
window opening, locate ALL loose-
NOTE: The hinge is a 2-part hinge
held together by the hinge pin.
panel in the opening and slide to the
Tip: To distribute the height gap evenly on the top
and bottom, a shim is recommended.
Tip: The shim that is marked with a pencil, can be
used as a guide for the right panel height spacing.
gap, make a small mark where the top
}Hinge
25 26
smithandnoble.com 800.248.8888
Installing the Right Hinge
the panel and place the right panel
in the window opening and slide to
the height gap evenly in the window
Tip: To distribute the height gap evenly in
reference to the left panel, use the shim that was
marked (on previous page).
Marking Position of Hinge
gap, make a small mark where the
Now that your left panel is secured, we will begin installing your right panel.
Installing the Left Hinge
Remove the hinge pin to separate the
NOTE: counter sink portion of hinge.
Tip: For flush mount panel: line the back of the
hinge barrel with the moulding/wall surface.
positioned, install screws into the
NOTE: Center set screw will be
installed in later steps.
Tip: Pre-drilling is recommended for proper setting
of screws. #6 countersink drill bit works best.
With the top hinge pin secured,
NOTE: Center set screw will be
installed in later steps.
Tip: Pre-drilling is recommended for proper setting
of screws. #6 countersink drill bit works best.
Slotted hinge holes
Slotted hinge holes
Panel in the
NOTE: If the panel has more than
2 hinges, go ahead and install the
screws to the rest of the hinges.
Push shim until stile is in
Panel in the window
.
{
Hinge
27 28
smithandnoble.com 800.248.8888
Remove the hinge pin to separate
the hinge and place onto window
NOTE: counter sink portion of hinge.
Tip: For flush mount panel: line the back of the
hinge barrel with the moulding/wall surface.
positioned, install screws provided
Note: Center set screw will be
installed in later steps.
Installing the Right Panels
Tip: Pre-drilling is recommended for proper setting
of screws. #6 countersink drill bit works best.
Place the right shutter panel into the
hinge that is now attached to the
wall and insert hinge pin into the
With the top hinge pin secured,
NOTE: Center set screw will be
installed in later steps.
Tip: Pre-drilling is recommended for proper setting
of screws. #6 countersink drill bit works best.
Slotted hinge holes
NOTE: If the panel has more than
2 hinges, go ahead and install the
screws to the rest of the hinges.
Slotted hinge holes
29 30
smithandnoble.com 800.248.8888
Hinge spacer installed
Loosen screws on panel
Tighten screws
Installing Hinge Spacers
Now that your panels and hinges
are installed, close panels, check
Loosen screws and
Installing the Light Blocks
You are now ready to install the
NOTE: Pre-drilling is recommended if
screws are being used.
Tip: For BEST results; a nail gun should be used.
31 32
smithandnoble.com 800.248.8888
Tools & Parts
Pencil, ¼" nut driver, level, and a drill with a 116
•
•
•
•
screwdriver to separate
Strip
Assemble Frames
Make sure fillers stay
with their frame and window.
Installing the Left Hang Strip
Tip: For flush panel installation, line the backside
of hinge barrel with the wall surface.
33 34
smithandnoble.com 800.248.8888
Installing the Right Hang Strip
(cont)
With hang strip properly positioned
in the opening, insert screw in top
pre-drilled holes and secure right
Installing the Panels
the window opening and slide into
Installing the Left Hang Strip
(Cont)
With hang strip properly positioned
in the opening, insert screw in top
(refer to tip
above for flush panel installation).
Installing the Right Hang Strip
(Cont)
Place right hanging strip along the
Tip: For flush panel installation, line the backside
of hinge barrel with the wall surface.
tightened, line up
tightened, line up
With hinge aligned,
With hinge aligned,
With hinge lined up,
With hinge lined up,
Position right Hang
Strip
35 36
smithandnoble.com 800.248.8888
loosen screws in the slotted
DO NOT REMOVE SCREWS
loosen screws in the slotted
DO NOT REMOVE SCREWS
Installing the Panels (cont)
With all hinge pins installed, open
shutter panel into the window
hinge, insert hinge pins into all
rest lightly on the sill whenever
Adjustments to the panels are made
at the hinge.
Note: Set screws are to be installed
once all adjustment have been
made.
Tip: Mark your panel or hang strip before
loosening the screws for a reference point.
Adjusting the Hinges
Prior to loosening screws, mark your
starting point for reference.
NOTE: Mark the top of the hinge
when adjusting up. Mark the bottom
of the hinge when adjusting down.
Prior to loosening screws, mark your
desired ending point for reference.
NOTE: Mark is made at the ending
point of how much side movement
you need. Hinge is then moved to
mark.
37 38
smithandnoble.com 800.248.8888
Pre-drilling is recommended to avoid
Installing Hanging Strip Inserts
your panels and check the gaps
are operating properly and gaps are
press hanging strip inserts into right
NOTE: Inserts MUST be installed
prior to installing the top and bottom
light blocks.
Installing Light Blocks
Installing Light Blocks (cont)
panel aligned with wall plain, hold
NOTE: We will not provide a top
light block for Café shutter.
Using Nail
Gun
Using
Screws
Using
Screws
Table of contents
Other Smith & Noble Indoor Furnishing manuals
Smith & Noble
Smith & Noble Uptown Wood Shutters Series User manual
Smith & Noble
Smith & Noble Honeycomb Shades User manual
Smith & Noble
Smith & Noble Solar & Roller Shades User manual
Smith & Noble
Smith & Noble Cellular Operating instructions
Smith & Noble
Smith & Noble Deco Metal Hardware User manual
Smith & Noble
Smith & Noble Metro Track Round Wood Hardware User manual
Smith & Noble
Smith & Noble Luxe Linen Honeycomb Shades User manual
Smith & Noble
Smith & Noble Smart Shades Operating instructions
Smith & Noble
Smith & Noble Metro Track Flat Wood Hardware User manual
Smith & Noble
Smith & Noble Fusion Hardware User manual
Smith & Noble
Smith & Noble Metro Track Flat Wood Hardware User manual
Smith & Noble
Smith & Noble Fusion Hardware User manual
Smith & Noble
Smith & Noble Solar & Roller Shades User manual
Smith & Noble
Smith & Noble Solar & Roller Shades User manual
Smith & Noble
Smith & Noble Honeycomb Motivia Motorization User manual
Smith & Noble
Smith & Noble Smart Shades Operating instructions
Smith & Noble
Smith & Noble Deco Metal Hardware User manual
Smith & Noble
Smith & Noble Roman Shades User manual
Smith & Noble
Smith & Noble Fusion Hardware User manual
Smith & Noble
Smith & Noble Honeycomb Shades Operating instructions
Popular Indoor Furnishing manuals by other brands
agatameble
agatameble CHRBS821 Assembling Instruction
Twin Star Home
Twin Star Home ST90151 Assembly instructions
Simple Home
Simple Home WyndenHall Brooklyn + Max AXCAMH-003 manual
Home Styles
Home Styles Naples Entertainment Stand 88 5530 09 Assembly instructions
Disc-O-Bed
Disc-O-Bed L Assembly instructions
QU-AX
QU-AX 76 16 TF 0x manual
HAMPTON BAY
HAMPTON BAY 133-003-2ST-L Use and care guide
Simpli Home
Simpli Home WyndenHall brooklyn+max AXCPF-60 quick start guide
Crown Mark
Crown Mark Hartwell 2795CG-S-24 Assembly instruction
HOMEDEPOT
HOMEDEPOT E02GF100 Use and care guide
SouthShore
SouthShore 4257 Assembly instructions
Zest 4 Leisure
Zest 4 Leisure Bahama Square Table Assembly instructions
HAMPTON BAY
HAMPTON BAY 151-115-7D-V2-NF Use and care guide
Home Styles
Home Styles 20 05050 0077 Assembly instructions
PB TEEN
PB TEEN Chelsea Platform Bed manual
HunterDouglas
HunterDouglas Design Studio Roman Shades Straight-Pull... Installation operation care
agatameble
agatameble WHITEBLACK 1D3S Instructions for assembling furniture
Vintage view
Vintage view CC2-DOOR installation instructions