Smith & Noble Metro Track Round Wood Hardware User manual

STEP BY STEP INSTALLATION INSTRUCTIONS
Ceiling Mount
Single Rod Set
Metro Track Round
Wood Hardware

2
800.248.8888
1smithandnoble.com
A Smooth Set-Up
We want you to love your new hardware and that includes
having a smooth installation experience. We suggest saving
        
please reach out to us for help. It’s why we’re here. Call us at
800.248.8888 for more info on installation.
We recommend you hold on to all packaging until your
hardware is fully installed. Should something go wrong (we
          
painless as possible.
Customer Service Hours
Monday — Friday: 6am — 6pm PT
Saturday — Sunday: 7am — 4pm PT
smithandnoble.com
Everything
You Need
Table of Contents
Step 1 - Getting Started ..................................3
Overview - Ceiling Mount Single Rod Set .....................4
Step 2 - Marking Bracket Placement .......................5
Step 3 - Attaching the Rod Connector......................6
Step 4 - Placing Carriers & End Stops ......................7
Step 5 - Attaching Bracket to the Rod ......................8
Step 6 - Attach Finials....................................9
Step 7 - Attaching Brackets to the Ceiling .................10
Step 8 - Attaching Drapery to Rod ........................11
Accessories - Baton/Wand ..................................12
Care & Cleaning ...........................................13
Notes .....................................................14
Warranty ..........................................Back Cover

34
smithandnoble.com 800.248.8888
STEP 1 - GETTING STARTED OVERVIEW
Metro Track Round Wood Ceiling Mount Single Rod
FINIAL
FINIAL
ROD
MOUNTING
BRACKET
MOUNTING
BRACKET SET SCREW
SET SCREW
MASTER
CARRIER
CARRIERS

need. You’ll need to make sure the surface you intend to install your hardware is sturdy enough
to accommodate the brackets. If you’re screwing directly into a surface this means locating
 
you’ll need to use a secure fastener (as illustrated) but please note this piece is not included.
Tools & Parts
WALLBOARD OR PLASTER:
Hollow wall applications: Use a secure fastener designed

METAL:
Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE:



the fastener manufacturer’s instructions regarding proper installation.
TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE:
764
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the
screws are too tight this may cause the screw itself to break off in the wall or window frame.
MOLLY
BOLT
SELF DRILLING
ANCHOR
TOGGLE
BOLT
SCREWS SET SCREWS CEILING MOUNT BRACKET
ALLEN WRENCHES CARRIERS
LEVEL
(NOT INCLUDED)
PENCIL
(NOT INCLUDED)
SCREWDRIVER
(NOT INCLUDED)
POWER DRILL
(NOT INCLUDED)
MOUNTING
RING
MOUNTING
BRACKET
HEX NUT
ROD QTY BRACKET QTY ROD WIDTH
1 2 
1 3 8
2 4 8
2 5 8
2 7 8
3 7 8
BACK VIEW

56
smithandnoble.com 800.248.8888
STEP 2 - MOUNTING THE BRACKET STEP 3 - ATTACHING THE ROD CONNECTOR
CENTER
     
have received a rod connector.
A rod connector is the short piece of
metal placed inside each end of the
rods in a multi-segment system to join
them together.
Join track sections together and fasten
securely with set screws.
2 SEGMENTS OF ROD
ROD CONNECTOR
ROD
RODSET
SCREW
SPLICE
ROD CONNECTOR
Place the panel on the rod. Hold it up
to the spot you wish to install it making
sure there is enough spacing from wall
to where the back of drapery will hit.
Usually about 2” away from wall or
window. After you’ve located the ideal

where the back of the rod is resting.
Remove the panel from the rod and
then center the rod over the window
opening at the desired spot. Using the
      
rod are positioned; if you’re using a

between these two spots as well.
If you have more than one center
bracket spread these evenly between
the two end brackets and center point.

that splice is as well on the wall since
you will need to add the special splice
bracket at that point as well. Measure
6” inward from the marks you’ve
made on both ends and mark those
spots. This is where the end brackets
will be installed.
Place ceiling bracket level against
ceiling at the marked spots & mark the
screw hole locations for all brackets.

78
smithandnoble.com 800.248.8888
Adding or Removing
Carriers to the Rod
Your track rod will come with all master
carriers and regular carriers pre-
installed. If you need to add or take
out some carriers depending on your
     
the rod.
Remove the carrier & end stop
and either add or take out the
carriers needed.
Placing End Stops on
the Rod
SPLIT DRAPERY (A)
Once all carriers have been placed in
  
   
each end and the second carrier so
end of drape does not move when
drape is closed.
ONE WAY DRAW DRAPERY (B)

   
the end and the second carrier of the
side you won’t be opening it from so
the end of drape does not move when
drape is closed.
STEP 4 - PLACING CARRIERS & END STOPS STEP 5 - ATTACHING THE BRACKET TO THE ROD
Slide in the ceiling bracket cradle into
the rod.
Do not tighten at this time.
Attach End Cap Finial.
CEILING BRACKET
CRADLE
SET
SCREW ROD
END CAP
FINIAL
BOne Way Draw
End stop & Carrier
positions
ASplit Draw
End stop & Carrier
positions
END STOP
END
STOP
FIRST
CARRIER
MASTER
CARRIER
MASTER
CARRIER
CARRIERS
END
STOP

910
smithandnoble.com 800.248.8888
STEP 6 - ATTACH FINIALS STEP 7 - ATTACHING BRACKETS TO THE CEILING
Hold the rod up and attach the bracket

bracket with the marks you made on
ceiling on a previous step.
Be sure and attach the bracket to the
ceiling with the appropriate mounting
hardware. (It is always recommended
to try and attach to the ceiling joists
found inside ceiling. Where this is not
possible please use an anchor suitable
to carry the weight of your hardware
selection as well as your draperies and
any accessories.)
Align the ceiling bracket cradle screw in
the back of the track with the brackets
mounted to the wall. Slide the cradle
screw onto the ceiling bracket but don't
tighten.
Center the track over the window
opening by sliding the track left or right
on the bracket cradles. When the track
     
bracket & tighten.
Tighten the set screw on the front of the
ceiling bracket to make sure the rod is
attached strongly to the bracket.
Slide in End Cap onto rod and
tighten set screw.
END CAP FINIALS
END CAP FINIAL
ROD
SET
SCREW
BRACKET
CRADLE
BRACKET
CRADLE
SET SCREW
END CAP
FINIAL
FINIAL
SET
SCREW
CEILING
BRACKET
CEILING
BRACKET
BOLT
BRACKET
CRADLE
BRACKET
CRADLE
ROD/TRACK
CEILING
BRACKET
CEILING
BRACKET

11 12
smithandnoble.com 800.248.8888
Insert drapery pin hooks into carriers
and master carriers.
Split Drapery

center and go towards the ends.
Draw one side
For drapery opening from one side
     
side towards the end.
STEP 8 - ATTACHING DRAPERY TO ROD ACCESSORIES
Baton/Wand (optional)
Baton/Wand will be pre-attached to
the master carrier(s).
CLIP
BATON/
WAND
MASTER CARRIER
BATON/
WAND
BACK VIEW OF ROD
BACK VIEW OF ROD
MASTER
CARRIER
MASTER
CARRIER
WAND
WAND
ROD
ROD
DRAPERY PIN
DRAPERY PIN

13 14
smithandnoble.com 800.248.8888
Minimal care and cleaning is needed to maintain the beauty of your Hardware.
To Vacuum: Use brush or dust head attachment.

NOTES
CARE & CLEANING

© 2019 Smith & Noble Home, Inc. All Rights Reserved SN1019
Warranty Service
           
products come with a limited lifetime warranty. The warranty applies to the
            
covers defects in material or craftsmanship. Hardware must have been properly
installed. We reserve the right to determine if your hardware warrants a repair
or a replacement. Visit smithandnoble.com/guarantee to see full details. In
need of warranty service? Call us at 800.248.8888 and we’ll arrange for a repair
or replacement ASAP.