Smith & Noble Deco Metal Hardware User manual

Wall Mount
Double Rod Set
Step by Step Installation Instructions
Deco Metal
Hardware

12
smithandnoble.com 800.248.8888
Table of Contents
Step 1 - Getting Started ..................................3
Overview - Wall
Mount Double Rod Set .......................4
Step 2 - Mounting the Brackets ...........................5
Step 3 - Attaching the Rod Connector......................7
Step 4 - Placing Carries & End Stops ..................... 8-9
Step 5 - Attach Finials ...................................10
Step 6 - Attaching Bracket Posts to Bracket Bases ..........11
Step 7 - Attaching Back Rod .............................12
Step 8 - Attaching Drapery to Rod ........................13
Accessories . ..............................................14
Care & Cleaning ...........................................14
Warranty ..........................................Back Cover
A Smooth Set-Up
We want you to love your new window coverings and
that includes having a smooth installation experience. We

or questions, please reach out to us for help. It’s why we’re here.
Call us at 800.248.8888 for more info on installation.
We recommend you hold on to all packaging until your
window coverings are fully installed. Should something go
wrong (we strongly doubt it), we want any potential returns to
be a painless as possible.
Customer Service Hours
Monday — Friday: 6am — 6pm PT
Saturday — Sunday: 7am — 4pm PT
smithandnoble.com
Everything
You Need

34
smithandnoble.com 800.248.8888
Deco Metal Wall Mount Double Rod Set
STEP 1 - GETTING STARTED OVERVIEW
SCREWS SET SCREWS END & CENTER BRACKET
ALLEN WRENCHES
FRONT OR
BACK ROD
BACK ROD
ONLY
CARRIERS
CENTER SUPPORT BRACKETS
(OPTIONAL)
PENCIL & SCREWDRIVER
(NOT INCLUDED)
POWER DRILL
(NOT INCLUDED)
LEVEL
(NOT INCLUDED)
ROD QTY BRACKET QTY ROD WIDTH
2 2 12"—60"
2 3 8"—96"
2 4 8"—106"
4 5 8"—156"
4 7 8"—212"
4 7 8"—204"
6 9 8"—252"
611 8"—288"
613 8"—312"
813 8"—384"
MOUNTING
PLATE
CENTER
BOLT COVER PLATE
INNER
POST OUTER POST
FINIALROD
MOUNTING
BRACKET
MASTER
CARRIER CARRIERS
END
CAP FINIAL
Before you begin, check the accompanying diagram to make sure you have all the parts you need.
You’ll need to make sure the surface you intend to install your hardware is sturdy enough to
accommodate the brackets. If you’re screwing directly
into a surface this means locating wood studs that are
strong enough to securely bond with the included
screws. Otherwise, you’ll need to use a secure fastener
(as illustrated) but please note this piece is not included.
WALLBOARD OR PLASTER: Hollow wall applications: Use a secure fastener designed

METAL: Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE:
screws.When selecting a fastener be sure it’s designed to support the weight of the product being
installed (if you’re not sure, either give us a call or ask a professional at your local hardware store).
Once obtained, follow the fastener manufacturer’s instructions regarding proper installation.
TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE: Pencil, screwdriver, ¼" nut driver,
level, and a drill with a
764
"drill bit.
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the screws
are too tight this may cause the screw itself to break off in the wall or window frame.
Parts & Tools
MOLLY
BOLT
SELF DRILLING
ANCHOR
TOGGLE
BOLT

56
smithandnoble.com 800.248.8888
Place the front panel on the rod. To
ensure it drapes at the correct length,
hold it up to the spot you wish to install
it; this will allow you to raise or lower
your treatment as desired. After you’ve
located the ideal location, use a pencil
to mark the wall where the top of the
rod is resting.
Remove the panel from the rod and
then center the rod over the window
opening at the desired height. Using
the pencil, mark where the ends of
each rod are positioned; if you’re using
a center bracket, note the middle point
between these two spots as well. If you
have more than one center bracket
spread these evenly between the two
end brackets and center point. If you
have a spliced rod, mark where that
splice is as well on the wall since you
will need to add a bracket at that point
as well. Measure 6” inward from the
marks you’ve made on both ends and
mark those spots. This is where the end
brackets will be installed.
Place bracket level against wall at the
marked spots. Using a pencil, lightly
draw a circle around the base of the
bracket onto wall (see Figure A). Check
to make sure the circles are level &
aligned with each other.
Remove mounting plate and center it
inside of the circle outline on wall. Mark
the screw hole locations for all brackets
(see Figure B).
Attach the metal mounting plate to the
wall, aligning the holes in the plate with
the marks made in the previous step
       
plate to the wall with the appropriate
mounting hardware. (It is always
recommended to try and attach to
the wood studs inside the wall. Where
this is not possible please use a wall
anchor suitable to carry the weight of
your hardware selection as well as your
draperies and any accessories.)
Place bracket cover plate on top of
mounting plate and thread in the inside
post. Make sure to screw on inside post
very tightly. Do not leave any play.
STEP 2 - MOUNTING THE BRACKETS STEP 2 - MOUNTING THE BRACKETS
OUTSIDE
POST
MOUNTING
PLATE
COVER
PLATE
FIGURE B
Mark all holes needed
showing locations of screw
holes for all brackets.
BACK PLATE
FIGURE A
6"
CENTER ROD

78
smithandnoble.com 800.248.8888
STEP 3 - ATTACHING ROD CONNECTOR
FRONT ROD
Depending on your order, you may
have received two rod connectors.
A rod connector is the short piece of
metal placed inside each end of the
rods in a multi-segment system to join
them together. The rod connector
will be placed at the back of the track
(rod) (see Figure A). Join track sections
together and fasten securely with set
screws.
BACK ROD
Depending on your order, you may
have a rod connector. A rod connector
is the short piece of metal placed
inside each end of the rods in a multi-
segment system to join them together.
Depending on the size of the rod, the
rod connector will either be placed on
the back of the heavy duty track (rod)
(see Figure B) or inside the regular track
(rod) (see Figure C) .
Adding or Removing
Carriers to the Rod
FRONT ROD
Your track rod will come with all master
carriers and regular carriers pre-
installed. If you need to add or take out
     
of carriers to pin hooks in your drapery.
     
Remove the end stop click and either
add or take out the carriers needed.
Placing End Stops on the
Rod
Once all carriers have been placed in
the track, for split drapery (A), place
      
carrier from each end and the second
carrier so end of drape does not move
when drape is closed.
For one way draw drapery (B), place
      
carrier from the end and the second
carrier of the side you won’t be
opening it from so the end of drape
does not move when drape is closed.
STEP 4 - PLACING CARRIES & END STOPS
BACK
CARRIERS
ONLY
FIGURE A
ROD
CONNECTOR
ROD
CONNECTOR
CENTER
CONNECTOR
BRACKET
END STOP
FRONT &
BACK
CARRIERS
END STOP
MASTER
CARRIERS
(B) One Way Draw
End stop & Carrier
positions
ADD OR
REMOVE
CARRIERS TRACK
END STOP
(A) Split Draw
End stop & Carrier
positions CARRIERS
ROD
CONNECTOR
ROD CONNECTOR
FIGURE C
REGULAR TRACK (ROD)
FIGURE B
ROD
CONNECTOR
ROD CONNECTOR
HEAVY DUTY TRACK (ROD)

910
smithandnoble.com 800.248.8888
STEP 4 - PLACING CARRIES & END STOPS STEP 5 - ATTACH FINIALS
Adding or Removing
Carriers to the Rod
(cont.)
BACK ROD
Your track rod will come with all master
carriers and regular carriers pre-
installed. If you need to add or take out
     
of carriers to pin hooks in your drapery,
remove the end cap from rail and either
add or take out the carriers needed and
then re-install end cap.
Placing End Stops to
the Rod
Once all carriers have been placed in
the track, for split drapery (A), place
      
carrier from each end and the second
carrier so end of drape does not move
when drape is closed.
For one way draw drapery (B), place
      
carrier from the end and the second
carrier of the side you won’t be
opening it from so the end of drape
does not move when drape is closed.
END CAP
CARRIERS
(A) Split Draw
End stop & Carrier positions
CARRIERS
END STOP
(B) One Way Draw
End stop & Carrier positions
END STOP
tightening the set screw
(see Figure A).
FINIAL
SET
SCREW
FIGURE A

11 12
smithandnoble.com 800.248.8888
STEP 6 - ATTACH BRACKET POSTS TO BRACKET BASES STEP 7 - ATTACHING BACK ROD
Attach Bracket Posts to
Rod (Track)
Loosen hex screw on Outside Posts.
Then slide outside posts into back
channel of rod (see Figure A).
Align outside posts with Inside Posts.
Slide Outside Posts over Inside Posts.
Once all Outside Posts including
Center Supports are in place, tighten
posts securely by turning clockwise.
Tighten set screws.
1. Assemble Back Rod Clips for
Outside Posts.
2. Attach assembled clip to Outside
Posts.
3. Partially assemble Back Rod Clip
for Center Post.
4. Mount Center Clip to Center
Post and 
5. Clips must align to be able to
install track.
Place the front lip of the track into
the front edge of the clip. Rotate the
back of the track up into the clips
and snap into place.
TIGHTEN POST
CLOCKWISE
FIGURE A
INSIDE
POST
OUTSIDE
POST
BASE
LOOSEN
SET SCREW
TIGHTEN
SET SCREWS

13 14
smithandnoble.com 800.248.8888
Baton/Wand (optional)
Baton/Wand will be pre-attached to
the master carrier(s).
ACCESSORIESSTEP 8 - ATTACHING DRAPERY TO ROD
Insert drapery pin hooks into carriers
and master carriers
SPLIT DRAW DRAPERY
ONE-WAY DRAW DRAPERY
BACK VIEW OF ROD
BACK VIEW OF ROD
MASTER
CARRIER
MASTER
CARRIER
WAND
WAND
ROD
DRAPERY PIN
ROD DRAPERY PIN
CLIP
BATON/
WAND
MASTER CARRIER
BATON/
WAND

© 2019 Smith & Noble Home, Inc. All Rights Reserved
Warranty Service
The enjoyment of your hardware should be everlasting, which is why our
products come with a limited lifetime warranty. The warranty applies to
the original owner, requires a proof of purchase (hang on to your receipt!)
and covers defects in material or craftsmanship. Hardware must have been
properly installed. We reserve the right to determine if your hardware
warrants a repair or a replacement. Visit smithandnoble.com/guarantee
to see full details. In need of warranty service? Call us at 800.248.8888
and we’ll arrange for a repair or replacement ASAP.
SN122019
Minimal care and cleaning is needed to maintain the beauty of your Hardware.
To Vacuum: Use brush or dust head attachment.
To Dust: Use soft, clean cloth.
CARE & CLEANING