Smith & Noble Fusion Hardware User manual

STEP BY STEP INSTALLATION INSTRUCTIONS
Ceiling Mount
Double Corner Rod Set
Fusion
Hardware
© 2019 Smith & Noble Home, Inc. All Rights Reserved SN0519
Warranty Service
The enjoyment of your hardware should be everlasting, which is why our
products come with a limited lifetime warranty. The warranty applies to the
original owner, requires a proof of purchase (hang on to your receipt!) and
covers defects in material or craftsmanship. Hardware must have been properly
installed. We reserve the right to determine if your hardware warrants a repair
or a replacement. Visit smithandnoble.com/guarantee to see full details. In
need of warranty service? Call us at 800.248.8888 and we’ll arrange for a repair
or replacement ASAP.

2
800.248.8888
1smithandnoble.com
A Smooth Set-Up
We want you to love your new hardware and that includes
having a smooth installation experience. We suggest saving
        
please reach out to us for help. It’s why we’re here. Call us at
800.248.8888 for more info on installation.
We recommend you hold on to all packaging until your
hardware is fully installed. Should something go wrong (we
strongly doubt it), we want any potential returns to be a
painless as possible.
Customer Service Hours
Monday — Friday: 6am — 6pm PT
Saturday — Sunday: 7am — 4pm PT
smithandnoble.com
Everything
You Need
Table of Contents
Step 1 - Getting Started ..................................3
Overview - Ceiling Mount Double Corner Rod Set..............4
Step 2 - Mounting the Brackets ........................ 5 - 6
Step 3 - Attaching the Rod Connector......................7
Step 4 - Attaching the Finials and Rings ................. 8 - 9
Step 5 - Securing Rod to Brackets .........................9
Accessories - Baton/Wand ...................................10
Accessories - Ball Tiebacks...................................11
Accessories - Hold Back .................................12 - 13
Care & Cleaning ...........................................14
Warranty ..........................................Back Cover

34
smithandnoble.com 800.248.8888
STEP 1 - GETTING STARTED OVERVIEW
Before you begin, check the accompanying diagram to make sure you have all the parts you
need. You’ll need to make sure the surface you intend to install your hardware is sturdy enough
to accommodate the brackets. If you’re screwing directly into a surface this means locating
wood studs that are strong enough to securely bond with the included screws. Otherwise,
you’ll need to use a secure fastener (as illustrated) but please note this piece is not included.
Tools & Parts Ceiling Double Corner Rod Set
WALLBOARD OR PLASTER:
Hollow wall applications: Use a secure fastener designed

METAL:
Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE:

be sure it’s designed to support the weight of the product being installed (if you’re not sure,
either give us a call or ask a professional at your local hardware store). Once obtained, follow
the fastener manufacturer’s instructions regarding proper installation.
TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE:
Pencil, screwdriver, ¼" nut driver, level, and a drill with a 764" drill bit.
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the
screws are too tight this may cause the screw itself to break off in the wall or window frame.
MOLLY
BOLT
SELF DRILLING
ANCHOR
TOGGLE
BOLT
CEILING MOUNT BRACKETS
CEILING
BRACKETS
ROD QTY
(PER SIDE)
BRACKET QTY
(PER SIDE) ELBOW QTY ROD WIDTH
2 4 2 12"— 48"
2 6 8 4"—72"
2 8 2 4"—96"
410 24"—144"
414 24"—192"
614 24"—216"
618 24"—288"
822 24"—360"
826 24"—384"
FRONT
FINIAL
FRONT
ROD
CORNER
ELBOW
BRACKETS
BACK
ROD FRONT FINIAL
RINGS
WALLBOARD OR PLASTER:
Hollow wall applications: Use a secure fastener designed

METAL:
Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE:

be sure it’s designed to support the weight of the product being installed (if you’re not sure,
either give us a call or ask a professional at your local hardware store). Once obtained, follow
the fastener manufacturer’s instructions regarding proper installation.
TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE:
Pencil, screwdriver, ¼" nut driver, level, and a drill with a 764" drill bit.
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the
screws are too tight this may cause the screw itself to break off in the wall or window frame.
PENCIL
(NOT INCLUDED)
SCREWDRIVER
(NOT INCLUDED)
DRILL
(NOT INCLUDED)
LEVEL
(NOT INCLUDED)
SCREWS CORNER/ELBOW BRACKET
ALLEN WRENCHES
SET SCREWS

56
smithandnoble.com 800.248.8888
Mounting the Brackets
Check to make sure the circles are
level & aligned with each other.
Remove mounting plate and center
it inside of the circle outline on wall.
Mark the screw hole locations for all
brackets. See Figure B.
Attach the metal mounting plate to
the ceiling, aligning the holes in the
plate with the marks made in the pre-
vious step, see figure B. Be sure and
attach the plate to the ceiling with
the appropriate mounting hardware.
(It is always recommended to try and
attach to the ceiling joists found in-
side ceiling. Where this is not possi-
ble please use an anchor suitable to
carry the weight of your hardware
selection as well as your draperies
and any accessories.)
If using plastic expansion anchors,
pre-drill holes using 3/16" drill
bit. If drilling directly into a stud
or wood trim, pre-drill holes with
3/32" drill bit.
Screw on the decorative portion of
the bracket to the mounting base
until it is tight and the open side of
bracket faces horizontally and the
same direction on all. See Figure C.
STEP 2 - MOUNTING BRACKETS STEP 2 - MOUNTING BRACKETS
FIGURE B
FIGURE C
Mark all holes needed
showing locations of screw
holes for all brackets.
MOUNTING
PLATE
SET
SCREW
BRACKET
STEM
DECORATIVE
BASE
INSIDE
POST
MOUNTING
PLATE
Mounting the Brackets
Place the panel on the left back rod. Hold it
up to the spot you wish to install it making
sure there is enough spacing from wall to
where the back of drapery will hit. Usually
about 2” away from wall or window. After
you’ve located the ideal location, use a pen-
cil to mark the ceiling where the back of the
rod is resting. Repeat on other side.
Place the front panel on the front left rod.
Hold it up to the spot you wish to install it
making sure there is enough spacing from
back rod to where the back of drapery will
hit. Usually about 2 1/2” away from back
rod marking. After you’ve located the ide-
al location, use a pencil to mark the ceiling
where the center of the rod is resting.
Repeat on other side.
Remove the panel from the rods and
then center the rods over the window
opening at the desired spot. Using the
pencil, mark where the ends of each rod
are positioned; if you’re using a center
bracket, note the middle point between
these two spots as well. If you have more
than one center bracket spread these
evenly between the two end brackets
and center point. If you have a spliced
rod, mark where that splice is as well on
the wall since you will need to add the
special splice bracket at that point as
well. Measure 2” inward from the marks
you’ve made on both ends and mark
those spots. This is where the end brack-
ets will be installed.
Place ceiling bracket level against ceil-
ing at the marked spots. Using a pencil,
lightly draw a circle around the base of
the bracket onto ceiling, see Figure A.
FIGURE A
CENTER ROD
CENTER ROD
XX
XX
XX
XX
XX

78
smithandnoble.com 800.248.8888
Depending on your order, you may have
received a rod connector.
A rod connector is the short piece of met-
al tubing placed inside each end of the
rods in a multi-segment system to join
them together.
STEP 3 - ATTACHING THE ROD CONNECTOR STEP 4 - ATTACHING THE FINIALS & RINGS
ROD CONNECTOR
STEP 2:
Now slide the second rod segment
over the exposed end of the connector,
making sure there is no gap between the
two segments.
STEP 1:
On the open end of one-rod segment,
slide the connector halfway inside,
leaving the other half exposed.
ROD
SEGMENT
ROD
SEGMENT
ROD
CONNECTOR
Insert the left back rod through the first
bracket and then place the required
number of rings on the rod but leave two
rings out. Then slide the rod through the
second bracket. All the rings should now
be in between the two brackets.
For split drapery, add a ring at each end
of the rod and then attach the finial to the
left side of the rod and the elbow to the
right side of rod. This will prevent dra-
pery to be pulled all the way to one side
or the other when opening and closing
it. If you are opening your drapery only
from one side, leave one ring between
the finial and bracket on the side you
won’t be opening it from. Repeat steps
for front rod. See Below.
Proceed to install the right rod through
the first bracket and then place the re-
quired number of rings on the rod but
leave two rings out. Then slide the rod
through the second bracket. All the
rings should now be in between the two
brackets.
For split drapery, add a ring at each end
of the rod and then attach the finial to
the right side of the rod and the elbow
to the left side of rod. This will prevent
drapery to be pulled all the way to one
side or the other when opening and
closing it. If you are opening your dra-
pery only from one side, leave one ring
between the finial and bracket on the
side you won’t be opening it from.
ATTACH FINIAL
PLACE ONE RING
BETWEEN FINIAL
AND BRACKET
For treatments using rings and do not have a center support bracket
Attach the finial to one end of the rod
and slide it through the first bracket.
Position one of the drapery panels on
the rod, and then slide the rod through
the center support bracket. Position the
other drapery panel on the rod, and then
slide the rod through the last support
bracket. Cap the opposite end with the
second finial.
For treatments without rings and
no center support bracket
TIGHTEN
SET SCREW

910
smithandnoble.com 800.248.8888
Insert the rod through the end and center
support bracket. Before inserting it
through the last bracket, place half of the
required number of rings on the rod but
leave two rings out. Then slide the rod
through the last end bracket. Go back to
the opposite side and take the rod out
of the end bracket to allow you to place
the remaining of the rings minus two
of them. All the rings should now be in
between the two end brackets and
center support bracket.
For split drapery, add a ring at one end
of the rod and then attach the finial. This
will prevent drapery to be pulled all the
way to one side or the other when opening
and closing it. If you are opening your
drapery only from one side, leave one
ring between the finial and bracket on
the side you won’t be opening it from.
For treatments using rings and
have a center support bracket
Attach the finial to left end of the back
rod, and slide it through the first brack-
et. Position one of the drapery panels on
the rod, and then slide the rod through
the center support bracket. Position the
other drapery panel on the rod, and
then slide the rod through the last sup-
port bracket. Cap the opposite end with
the elbow. Repeat for front rod and right
side rods.
For treatments without rings and
no center support bracket
STEP 4 - ATTACHING THE FINIALS & RINGS
STEP 5 - SECURING ROD TO BRACKETS
ACCESSORIES
Baton/Wand (optional)
After your hardware is installed, attach
the baton to the eyelet of the first ring
by the clip.
Push clip through
the eyelet of the
drapery clip
Baton/Wand
BATON/
WAND
CLIP
EYELET
DRAPERY
RING
Baton/Wand
Once the rod has been placed on the
brackets, secure the rod in place by
tightening the bracket set screw with
the allen wrench provided. SET
SCREW
ATTACH FINIAL
PLACE ONE RING
BETWEEN FINIAL
AND BRACKET
TIGHTEN
SET SCREW

11 12
smithandnoble.com 800.248.8888
ACCESSORIES ACCESSORIES
Tiebacks (optional)
BALL TIEBACK
STEP 1
In order to locate where to install your
tiebacks, measure the height of the
window and divide this by two. Using
the previous calculation, mark that
spot on the wall with a pencil.
To ensure you like the way the panel
drapes, gather one side and sweep
it over to the approximate proposed
location. Once you’re sure the tieback
is in the perfect location, use your
pencil to mark the spot to install it.
Measure the distance from the
bottom or top of the window to the
tieback to mark the other side and
ensure they’re even.
Now hold the tieback hardware on
the wall at the desired location and
rest a level above it, adjusting it until
it’s straight.
STEP 2:
Place tieback level against wall in
desired locations and attach to the wall.
Hold Back (optional)
STEP 1
In order to locate where to install your
tiebacks, measure the height of the
window and divide this by two.
Using the previous calculation, mark
that spot on the wall with a pencil.
To ensure you like the way the panel
drapes, gather one side and sweep it
over to the approximate proposed lo-
cation. Once you’re sure the tieback is
in the perfect location, use your pencil
to mark the spot to install it.
Measure the distance from the
bottom or top of the window to the
tieback to mark the other side and
ensure they’re even.
STEP 2:
Hook installation is an option depend-
ing on desired drapery style. When
using the hook option assemble the
" pole,
as shown to the left (A).
STEP 3:
" pole un-
til both holes line up as shown to the
left (B).
STEP 4:
To install the mount screw, place it
through the center of the 1½" pole &
the optional hook, as shown to the left
(C).
HOOK
MOUNT SCREW
A
B
C
X

13 14
smithandnoble.com 800.248.8888
CARE & CLEANING
Minimal care and cleaning is needed to maintain the beauty of your Hardware.
To Vacuum: Use brush or dust head attachment.
To Dust: Use soft, clean cloth.
ACCESSORIES
STEP 5:
Attach the Hold Back to the wall by
holding Hold Back assembly above the
hook hole location. Fingers placed be-
low this point or on the wall can become
pinched between the wall and the
Hold Back (D).
STEP 6:
Locate the Hold Back screw and
mount Hold Back, as shown at right
(E).
STEP 7:
Assemble the Hold Back by placing
" pole. To secure
the finial to the pole tighten the 4 mm
set screw to the pole (F).
Keep fingers away
from edge and wall
during installation.
Keep fingers away
from edge and wall
during installation.
Hold Here
HOLD BACK FINIAL
D
E
F