Smith & Noble Luxe Linen Honeycomb Shades User manual

Step by Step Installation Instructions
Luxe Linen
Honeycomb Shades
Customer Service 800.248.8888 or visit us online at smithandnoble.com

1 2
For assistance, call smith+noble
Customer Service at
800.248.8888
Visit our website at
smithandnoble.com
THANK YOU for purchasing from smith+noble.
Your new window treatments have been custom
crafted from the highest quality materials.
Once installed, they will provide you with a
lifetime of beauty and trouble-free use.
INSTALLING your new shade is easy. Simply follow
our step-by-step instructions. We recommend that
you read through all the instructions before you
start. If you have questions, our customer service
representatives are available at 800.248.8888.
Do not dispose of packaging until the shade is
operating to your satisfaction.
Table of Contents
Getting Started ................................3
Cordlift - Standard & Top Down/Bottom Up .............4
Attaching the Brackets ...................... 5 - 6
Attaching Extension Brackets ....................7
Hanging the Shade............................7
Operating the Shade ..........................8
Breakthrough Cord Connector ...................8
Cordless - Standard & Top Down/Bottom Up ...........10
Attaching the Bracket..................... 11 - 12
Hanging the Shade...........................12
Removing the Shade..........................12
Operating the Shade .........................13
Troubleshooting .............................14
Loop Control - Standard, Top Down/Bottom Up & 2-on-1 ..16
Attaching the Brackets ........................17
Mounting the Brackets ........................18
Hanging the Shade...........................19
Removing the Shade..........................19
Operating the Shade .........................20
Installing Tension Device ......................20
Motorized Shades ............................22
Attaching the Brackets .................... 23 - 24
Attaching the Battery ..................... 24 - 25
Hanging the Shade...........................26
Setting up the Remote Control .............. 27 - 28
Operating the Shade .........................28
Hold Down Brackets (optional) ..................29
Level the Bottom Rail .........................29
Care + Cleaning ..............................30
Safety ......................................30
Warranty .............................. back page

3 4
Getting Started
Getting Started
Remove the shade from the
packaging.
Do not dispose of packaging
until the shade is operating to
your satisfaction.
Check the diagram to make sure
you have all the parts indicated
for the appropriate type of
installation.
NOTE: Do not attach the headrail
to the mounting bracket prior to
installation
Do not lower the shade yet.
Tools you will need to install your
blind: pencil, screwdriver, 1/4" nut
driver, level, pliers and a drill with
1/16" drill bit.
Your brackets must be securely
attached to the mounting surface.
When screwing into a surface,
the included screws must hit
wood studs. Otherwise, use a
secure fastener as illustrated
(not included).
Wallboard Or Plaster:
Use a secure fastener designed
for hollow wall applications.
Metal: Pre-drill holes and use
the included screws.
Concrete, Stone, Brick Or Tile:
Use a masonry drill and
appropriate plugs, anchors
or screws.
When selecting a fastener, make
sure it is designed to support
the weight of the product being
installed. Follow the fastener
manufacturer’s instructions for
proper installation. screws
(included)
toggle
bolt
self drilling
anchor
molly
bolt
note: When installing screws with a drill,
be careful not to over-tighten. This may
cause the screw to break off in the wall
or window frame.
2½"
2½"
Rail
For shade Standard Rail
widths of:Inside or Outside Mount Inside MountOutside Mount
Up to 40" 2 2 2
>40" to 72" 3 3 4**
>72" to 84" 4 4 5**
>84" to 120" 5* 5 6**
**76pudna021>
Large Rail
Use this Number of Brackets:
mounting
bracket
sidemount
bracket
(optional)
hold down
bracket
(optional)
extension
bracket
(optional)
Parts of the Shade
Standard + Top Down/Bottom Up
CORD
CLEAT
HEADRAIL
DRAW
CORD

5 6
Attaching the Brackets
Attaching the Brackets Attaching the Brackets
Cord Lift - Standard &
Top Down/Bottom Up
End brackets should be located
with centerlines 2 1⁄2" in from
each end.
* On Semi-Sheer shades over
84" wide, it is recommended
to use a second bracket
located next to the end
bracket at the Cord Lock.
** On Light Filtering shades
over 40" wide, it is recommended
to use a second bracket
located next to the end
bracket at the Cord Lock.
Depending on the width of the
shade, additional brackets may
be necessary evenly spaced
between the two end brackets.
Using the Installation Bracket
as a template, measure and
mark the center lines. When
mounting brackets, make sure
they are in line and level.
Attaching the Brackets (con't)
Inside Mount
The brackets are mounted flat against
the top sill surface.
To fully recess the shade requires a flat
surface with a minimum depth of 2" for
Semi-Sheer or 2
1
⁄ 2 " for Light Filtering.
Shallow mounting requires
3
⁄ 4 " min.
Outside Mount
The brackets are mounted with two screws
through the back end of the bracket flat
against the window molding or the wall
above the window. The bracket requires
a minimum surface 3⁄4" high.
Sidemount (optional)
Line the bracket top with the desired
height of the top of the headrail.
Mark holes for screws. Remove
brackets and drill holes. Insert screws
for keyhole slots only. Approximately 1⁄8"
of the screw should be left protruding.
Pull the cord lock assembly partially
out of the headrail and slide the
bracket on as shown. Push the
cordlock assembly and bracket
back all the way into the rail.
Remove the endcap from the opposite
end of the headrail. Slide the
remaining side mount bracket onto
the headrail. Replace the endcap
before sliding the bracket all the way
into the headrail.
Hook one bracket onto the screw in the
window frame, using the keyhole slot.
Bring the other end bracket over the
screw at the other side of the frame.
Slide down, flexing bracket inward until
the screw engages in the keyhole slot.
Make sure both brackets are slipped
down all the way in the keyhole slot so
that the screw is in the top portion of
the keyhole slot. Install a screw in the
bottom hole of each bracket. Tighten
all screws.
2½"
2½"
Rail
For shade Standard Rail
widths of:Inside or Outside Mount Inside MountOutside Mount
Up to 40" 2 2 2
>40" to 72" 3 3 4**
>72" to 84" 4 4 5**
>84" to 120" 5* 5 6**
**76pudna021>
Large Rail
Use this Number of Brackets:
Semi-Sheer Rail Light Filtering Rail
1 7⁄16"
Semi-Sheer Rail Light Filtering Rail
1 7⁄8"
2½"
2½"
Rail
For shade Standard Rail
widths of:Inside or Outside Mount Inside MountOutside Mount
Up to 40" 2 2 2
>40" to 72" 3 3 4**
>72" to 84" 4 4 5**
>84" to 120" 5* 5 6**
**76pudna021>
Large Rail
Use this Number of Brackets:
2½"
2½"
Rail
For shade Standard Rail
widths of:Inside or Outside Mount Inside MountOutside Mount
Up to 40" 2 2 2
>40" to 72" 3 3 4**
>72" to 84" 4 4 5**
>84" to 120" 5* 5 6**
**76pudna021>
Large Rail
Use this Number of Brackets:
21⁄2"
Cord Lock
1st Installation Bracket
2½"
2½"
Rail
For shade Standard Rail
widths of:Inside or Outside Mount Inside MountOutside Mount
Up to 40" 2 2 2
>40" to 72" 3 3 4**
>72" to 84" 4 4 5**
>84" to 120" 5* 5 6**
**76pudna021>
Large Rail
Use this Number of Brackets:
3/4" minimum
Mounting
Bracket
2" minimum for Semi-Sheer
2-1/2" minimum for Light Filtering
2½"
2½"
Rail
For shade Standard Rail
widths of:Inside or Outside Mount Inside MountOutside Mount
Up to 40" 2 2 2
>40" to 72" 3 3 4**
>72" to 84" 4 4 5**
>84" to 120" 5* 5 6**
**76pudna021>
Large Rail
Use this Number of Brackets:
2-1/2"
Mounting
Bracket
Sidemount
Bracket
(optional)
Sidemount
Bracket
(optional)
Keyhole
Slot

7 8
WARNING
To avoid entanlgement and strangulation,
keep cords out of the reach of young children.
Move cribs and furniture away from blind cords.
To further reduce hazards, this shade was built
with a cord connector which was designed to
break apart when force is applied from the top.
No safety system is fail-safe.
KEEP CORDS OUT OF REACH OF SMALL CHILDREN!
!
If your cord connector should happen to break apart, follow the instructions below to reassemble.
When the connector is
open, each side has a cord
coming in at the top, one
side has a cord coming in
from the bottom.
Fit the bottom edges
together. The side with
the cord fits into the side
without the cord.
Swing the top ends
together and press in the
middle to fully connet.
BREAKTHROUGH
CORD
CONNECTOR
Operating the shade + Breakthrough Cord Connector
Attaching Brackets + Hanging the Shade
Attaching Extension Brackets (Optional)
Hanging the Shade
Breakthrough Cord Connector
Optional Extension Brackets
are used to project the back
of the shade up to 23⁄8" from
the mounting surface.
This
will allow the shade to avoid
window cranks, door knobs,
etc. when raised and lowered.
Attach the Installation Bracket
to the Extension Bracket with
the nut and bold provided.
Center the shade over the
window opening at the desired
height. Mark the position of
the Extension Bracket on the
wall. Make sure the mounting
brackets are level. Mount the
Extension Brackets to the wall.
Unwind the cord from
the shade.
Hold the shade up near the
brackets and insert the front
clip of the bracket into the
front groove of the rail.
Center the shade over the
window opening at the
desired height.
Push the rail back and up
until the back clips of the
bracket are inserted into the
back groove of the rail.
To lower or release the shade,
pull the cord inward toward the
center of the shade.
To raise or lock the shade,
pull the cord straight down
and outward toward the edge
of the shade.
Nut
Bolt
Extension
Bracket
Rail Bracket
Push rail back and up until the
back clip snaps into the rail.
Operating the Shade
17⁄8"
minimum