Snorkel S3215L User manual

February 2020
Original Instructions
Part Number 1500834
MANUAL
OPERATOR’S
ANSI/CSA/CE/AS/NZS
Serial number 000017, 000019 and after
Replaces January 2020

The aerial platform is not electrically insulated. Death or serious injury will result from contact
with, or inadequate clearance from, an energized conductor.
Do not go closer than the minimum safe approach distance as dened by the Minimum Safe
Approach Distance section in Chapter 3–Safety.
Regard all conductors as energized.
Allow for electrical wire sag and aerial platform sway.
If the platform, scissors structure, or any part of the aerial platform contacts a high-voltage electrical
conductor, the entire machine can become electrically charged.
If that happens, remain on the machine and do not contact any other structure or object. This includes
the ground, adjacent buildings, poles, and any other objects that are not part of the aerial platform.
Such contact could make your body a conductor to the other object, creating an electrical shock hazard
resulting in death or serious injury.
If an aerial platform is in contact with an energized conductor the platform operator must warn ground
personnel in the vicinity to stay away. Their bodies can conduct electricity creating an electrical shock
hazard resulting in death or serious injury.
Do not approach or leave the aerial platform until the electricity has been turned o󰀨.
Do not attempt to operate the lower controls when the platform, scissors structure, or any part of the
aerial platform is in contact with a high-voltage electrical conductor or if there is an immediate danger
of such contact.
Personnel on or near an aerial platform must be continuously aware of electrical hazards, recognizing
that death or serious injury can result from contact with an energized conductor.
California
Proposition 65 Warning
Battery posts, terminals, and related accessories contain
lead and lead components, chemicals known to the
State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.

ADANGER
Do NOT Operate in
Windy or Gusty Conditions
Do NOT Add Anything That
Will Increase Wind Loading
Do NOT Operate Outside
During a Thunderstorm
Do NOT Go Closer Than The
Minimum Safe Approach Distance
Do NOT Operate a Stowed
MEWP on Rough or Uneven Terrain
Do NOT Operate an Elevated MEWP
Within 4ft (1.2m) of Any Drop-o󰀨 or Hole
Do NOT Operate an Elevated
MEWP on Rough or Uneven Terrain
Do NOT Drive an Elevated MEWP on
Soft, Uneven or Sloping Surfaces
Do NOT Exceed The Maximum
Allowable Manual Side Force
Do NOT Operate The MEWP
Without Su󰀩cient Clearance
Do NOT Use The MEWP As a
Lifting Tool or Crane
Do NOT Operate a Stowed MEWP
Within 4ft (1.2m) of Any Drop-o󰀨 or Hole
Do NOT Allow Ground Personnel
Near the MEWP During Operation
Do NOT Carry Loads That
Extend Beyond The Guardrails
Do NOT Lower The Platform Without
Checking For Obstructions
Do NOT Raise The Platform Without
First Checking For Obstructions
Do NOT Exceed The Platform
Main Deck Capacity
Do NOT Climb on The MEWPDo NOT Exceed The Platform
Extension Deck Capacity
Do NOT Operate an MEWP From
Trucks, Trailers, or Similar Equipment
Do NOT Operate an MEWP With
Tires That Are in Poor Condition
Do NOT Operate an MEWP That is
Damaged or Not Functioning Properly
Do NOT Engage In Any
Form of Horseplay
Do NOT Climb on
The Guardrails
Do NOT Strike or Bump Stationary
Objects With an Elevated MEWP
Do NOT Strike or Bump Stationary
Objects With a Stowed MEWP
Do NOT Operate an MEWP
While Physically Impaired
Do NOT Leave the MEWP
With The Key In It

Fall Restraint Lanyard Anchor Points
All fall restraint lanyard anchor points on Snorkel aerial work platforms have been tested with a force of 3,650 lbs (16.3 kN)
per person.
See below examples of anchor points used on Snorkel machines with their corresponding per person rating.
NOTE: There can be more anchor points in the platform than the maximum number of occupants allowed in the
platform. Refer to the machine specications for the correct occupancy rating before use.
Type 1
Type 2
Type 3
Type 4
Top View Top View
Top View Top View
Front View
Front View
Anchor point Type 1 is rated for one lanyard
attachment per loop. Refer to machine “Specica-
tions” and platform decals for maximum number of
platform occupants.
Two Lanyards
Attached
One Lanyard
Attached
Anchor point Type 2 is rated for two lanyard
attachments per loop. Refer to machine “Specications”
and platform decals for maximum number of platform
occupants.
Two Lanyards
Attached
One Lanyard
Attached
Anchor point Type 3 is rated for one lanyard
attachment per loop. Refer to machine “Specications”
and platform decals for maximum number of platform
occupants.
One Lanyard
Attached
One Lanyard
Attached
Anchor point Type 4 is rated for one lanyard
attachment per loop. Refer to machine “Specications”
and platform decals for maximum number of platform
occupants.

Warning
All personnel shall carefully read, understand and follow all safety rules and operating instructions
before operating or performing maintenance on any Snorkel aerial work platform.
Electrocution Hazard Tip Over Hazard Collision Hazard Fall Hazard
THIS MACHINE IS
NOT INSULATED!
NEVER elevate the platform
or drive the machine while
elevated unless the machine
is on a rm, level surface.
NEVER position the platform
without first checking for
overhead obstructions or
other hazards.
NEVER climb, stand, or sit
on platform guardrails or
midrail.
USE OF THE AERIAL WORK PLATFORM: This aerial work platform is intended to lift persons, their tools and materials
used for the job. It is designed for repair, assembly, stockpicking jobs, etc., and assignments at workplaces above head height
(ceilings, cranes, roof structures, buildings, shelving, etc.). All other uses of the aerial work platform are prohibited and the
rules below must be adhered to!
THIS AERIAL WORK PLATFORM IS NOT INSULATED! Refer to applicable national standards for safe approach distances.
Exceeding the specied permissible maximum load is prohibited! See “Platform Capacity” for details.
The use and operation of the aerial work platform as a lifting tool or a crane is prohibited!
NEVER exceed the manual force allowed for this machine. See “Manual Force” for details.
DISTRIBUTE all platform loads evenly on the platform.
NEVER operate the machine without rst surveying the work area for stationary or moving obstacles and surface hazards such
as holes, drop-o󰀨s, bumps, curbs, or debris; and avoiding them. NEVER strike or bump into stationary or moving obstacles
while driving or raising, lowering, or extending the platform.
USE THREE POINTS OF SUPPORT when entering or exiting the platform. Grasp the handrails, not the doors, with one hand on
each side. Use two hands and one foot on the step when climbing into and out of the platform.
PLATFORM passengers should watch their hands and ngers for pinch points while holding on the guardrails while the
platform is moving.
OPERATE machine only on surfaces capable of supporting wheel loads.
NEVER operate the machine when wind speeds exceed this machine’s wind rating. See “Beaufort Scale” for details.
Do not operate the aerial platform in windy or gusty conditions. Do not add anything to or take anything into the aerial platform
that will increase the wind loading such as billboards, banners, flags, etc.
IN CASE OF EMERGENCY push EMERGENCY STOP switch to deactivate all powered functions.
IF ALARM SOUNDS while platform is elevated, STOP, carefully lower platform. Move machine to a rm, level surface.
Climbing up the railing of the platform, standing on or stepping from the platform onto buildings, steel or prefab concrete
structures, etc., is prohibited! NEVER exit or enter the platform when it is elevated.
Dismantling the entry gate or other railing components is prohibited! Always make certain that the entry gate is closed!
It is prohibited to keep the entry gate in an open position when the platform is raised!
To extend the height or the range by placing of ladders, sca󰀨olds or similar devices on the platform is prohibited!
NEVER perform service on machine while platform is elevated without blocking elevating assembly.
INSPECT the machine thoroughly for cracked welds, loose or missing hardware, hydraulic leaks, loose wire connections, and
damaged cables or hoses before using.
VERIFY that all labels are in place and legible before using.
NEVER use a machine that is damaged, not functioning properly, or has damaged or missing labels.
To bypass any safety equipment is prohibited and presents a danger for the persons on the aerial work platform and in its
working range.
NEVER charge batteries near sparks or open ame. Charging batteries emit explosive hydrogen gas.
Modications to the aerial work platform are prohibited or permissible only at the approval by Snorkel.
AFTER USE, secure the work platform from unauthorized use by turning the keyswitch o󰀨 and removing key.
The driving of MEWP’s on the public highway is subject to national tra󰀩c regulations.
Certain inherent risks remain in the operation of this machine despite utilizing proper design practices and safeguarding.
Care must be taken to ensure that the machines meets the requirements of stability during use, transportation, assembly,
dismantling when out of service, testing, or foreseeable breakdowns.
In the event of an accident or breakdown see “Emergency Lowering.” Do not operate the aerial platform if it is damaged or not
functioning properly. Qualied maintenance personnel must correct the problem before putting the aerial platform back into
service.
SAFETY RULES

S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834
Table of Contents
Electrical Danger ............................ Inside Front Cover
Proposition 65 Warning .................. Inside Front Cover
Danger Symbols............................. Inside Front Cover
Lanyard Anchor Points ................... Inside Front Cover
Safety Rules ................................... Inside Front Cover
Chapter 1 – Introduction
Aerial Platform Features.............................................1
Options .......................................................................1
Operator’s Manual......................................................1
Safety Alerts ...............................................................1
Operation....................................................................1
Maintenance...............................................................2
Used Material Disposal ...........................................2
Manual of Responsibilities – ANSI..............................2
MEWP Safe Use – AS/NZS........................................2
AS/NZS 1418.10 Commissioning...............................2
CE Compliance...........................................................2
Additional Information.................................................2
Chapter 2 – Specications
Component Identication ............................................3
General Specications – S3215L ...............................4
General Specications – S3215E...............................5
General Specications – S3219E ...............................6
General Specications – S3220E ...............................7
General Specications – S3226E ...............................8
General Specications – S4726E ...............................9
General Specications – S4732E .............................10
Chapter 3 – Safety
Electrocution Hazards .............................................. 11
Minimum Safe Approach Distance – ANSI ............... 11
Minimum Safe Approach Distance – AS/NZS...........12
Platform Capacity .....................................................12
Manual Force............................................................12
Wind Speeds ............................................................12
Prestart Inspection....................................................12
Work Place Inspection and Practices.......................12
Operation..................................................................13
Tip-Over and Falling Hazards...................................13
Electrical System......................................................14
Hydraulic System......................................................14
Placards and Decals.................................................14
General Safety Rules ...............................................14
Chapter 4 – Safety Devices
Emergency Stop Controls.........................................17
Control Select/Ground Operation Switch..................17
Upper Control Interlock Switch.................................17
Drive Motion Alarm ...................................................18
Pothole Protector Skids............................................18
Drive/Lift Pothole Protector Interlock........................18
Drive/Lift Level Sensor Interlock...............................18
Progressive Tilt – S3226E Only ............................18
Lowering Alarm.........................................................19
Emergency Lowering Lever/Handle .........................19
Safety Prop...............................................................19
Guardrails.................................................................20
Ground Fault Circuit Interrupter................................20
Tilt Alarm...................................................................20
Overload Protection..................................................20
Lowering Interrupt – CE/AS/NZS...................................20
Horn..........................................................................21
Flashing Light ...........................................................21
Snorkel Guard ..........................................................21
Chapter 5 – Gauges and Displays
Battery Charge Indicator – ProCharger....................23
Battery Charge Indicator – Pylon..............................23
Battery Condition Indicator .......................................23
Diagnostic Center Display ........................................24
Chapter 6 – Batteries
General Maintenance ...............................................25
Charging...................................................................25
Chapter 7 – Controls
Battery Disconnect ...................................................27
Lower Controls .........................................................27
Emergency Stop Button ........................................27
Control Selector/Ground Operation Switch ...........27
Platform Raise/Lower Switch ................................27
Upper Controls .........................................................28
Emergency Stop Button ........................................28
Drive/Lift Selector Switch ......................................28
Joystick .................................................................28
Interlock Switch .....................................................29
Steer Switch ..........................................................29
Drive Range Switch...............................................29
Horn Button ...........................................................29
Battery Condition Indicator....................................29
Loading Controls ......................................................29
Emergency Stop Button ........................................29
Interlock Button .....................................................30
Drive Switch ..........................................................30
Steer Switch ..........................................................30
Override Switch.....................................................30
Chapter 8 – Prestart Inspection
Operator’s Manual....................................................31
Electrical System......................................................31
Battery Fluid Level ................................................31
Battery Terminals...................................................32
Battery Charger.....................................................32
Safety Prop...............................................................32
Cables and Wiring Harness......................................33
Hydraulic System......................................................33
Fluid Level.............................................................33
Hoses, Tubes, and Fittings....................................33
Free-Wheeling Valve .............................................34
Diagnostic Center Display ........................................34
Tires and Wheels......................................................34
Ground Strap............................................................34

Table of Contents
S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834
Lower Control Station...............................................34
Operating Controls ................................................34
Emergency Stop....................................................35
Lowering Alarm .....................................................35
Pothole Protector Interlock....................................35
Emergency Lowering System...................................36
Structures .................................................................36
Weldments ............................................................36
Rollers and Slide Blocks .......................................37
Fasteners ..............................................................37
Upper Control Station...............................................37
Guardrail System ..................................................37
Platform Extension ................................................37
Operating Controls ................................................38
Emergency Stop....................................................39
Horn Button ...........................................................39
Lowering Alarm .....................................................39
Drive Alarm............................................................39
Electrical Power Outlet .............................................39
Flashing Light ...........................................................40
Pipe Rack .................................................................40
Panel Carrier ............................................................40
Placards and Decals.................................................40
Prestart Inspection Checklist....................................43
Chapter 9 – Operation
Preparing for Operation............................................45
Lower Controls .........................................................45
Upper Controls .........................................................45
Removable Upper Controls/Side Drive .................46
Platform ....................................................................46
Raising and Lowering............................................46
Lowering Interrupt – CE/AS/NZS ..........................46
Overload Protection ..............................................47
Extending ..............................................................47
Fold Down Guardrails...............................................47
Driving and Steering.................................................48
Drive Range Switch...............................................48
Drive Speeds ........................................................48
Drive/Lift Pothole Protector Interlock........................49
Drive/Lift Level Sensor Interlock...............................49
Progressive Tilt – S3226E Only ............................49
Swing-Out Trays .......................................................49
Electrical Power Outlet .............................................50
Pipe Rack .................................................................50
Panel Carrier ............................................................51
Snorkel Guard ..........................................................51
Override Button ........................................................52
After Use Each Day..................................................52
Chapter 10 – Stowing and Transporting
Stowing.....................................................................53
Transporting .............................................................53
Lifting With a Forklift..............................................53
Winching ...............................................................53
Driving ...................................................................55
Hoisting .................................................................56
Securing for Transport...........................................57
Storage..................................................................58
Chapter 11 – Emergency Operation
Emergency Lowering................................................59
Towing ......................................................................59
Chapter 12 – Troubleshooting
Troubleshooting Chart ..............................................63
Appendix A – Glossary
Appendix B – EC Declaration of Conformity
Appendix C – Inspection Checklists
Limited Warranty

S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834 1
Chapter 1 – Introduction
Aerial Platform Features
The aerial platform is a self-propelled scissors lift that has
been designed to raise personnel, their tools, and material
to the workstation. The aerial platform has been designed
for use on hard surface oors such as concrete.
The S3215L/S3215E/S3219E/S3220E uses a single
hydraulic cylinder to raise and lower the platform. The
S3226E/S4726E/S4732E machines have two hydraulic
cylinders to raise and lower the platform. A hydraulic
motor on each of the front drive wheels provides power
to move the aerial platform.
The standard machine includes the following features:
yProportional drive and lift up control
yDrivable at full height
yTwo speed drive
yDrive motion alarm
yNon-marking tires
yAutomatic pothole protection system
yLevel sensor with drive/lift interlock
yPlatform overload system – ANSI S3226E
yDiagnostic center display
yBattery condition indicator
yManual lowering valve
yLockable battery disconnect switch
yTie-down/lifting lugs
yHeavy duty battery charger
ySwing-out hydraulic component and battery trays
yNon-slip metal platform oor
yPlatform extension
y125 volt AC electrical outlet with GFCI
yScissor arm safety support prop
yLowering alarm
yLowering interrupt – CE/AS/NZS
yHorn
yRear forklift pockets
ySaloon style entry doors
yFive year limited warranty
The aerial platform has been manufactured to conform to all
applicable requirements of the following organizations.
yOccupational Safety and Health Administration (OSHA)
yAmerican National Standards Institute (ANSI)
Options
The following options may be provided on the machine:
yFlashing light
yPipe rack
yPanel carrier
yPlatform overload system
yInverter
yAirline to platform
ySnorkel Guard
yTray locks
yBumpguard
yEuropean conformity (CE) compliance
• Australian/New Zealand Standards
(AS/NZS) compliance
yCanadian Standards Association (CSA) compliance
Operator’s Manual
This manual provides information for safe and proper
operation of the aerial platform. Some information in this
manual refers to options that may or may not be on your
machine. Read and understand the information in this
Operator’s Manual before operating the aerial platform
on the job.
Additional copies of this manual may be ordered from
Snorkel. Supply the model and manual part number from
the front cover to assure that the correct manual will be
supplied.
All information in this manual is based on the latest
product information at the time of publication. Snorkel
reserves the right to make product changes at any time
without obligation.
Safety Alerts
A safety alert symbol is used throughout this manual to
indicate danger, warning, and caution instructions. Follow
these instructions to reduce the likelihood of personal
injury and property damage. The terms danger, warning,
and caution indicate varying degrees of personal injury
or property damage that can result if the instruction is
not followed.
Danger
Indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
This signal word is to be used in the most extreme
situations.
Warning
Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
Caution
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices.
Notes
Notes are used to provide special information or helpful
hints to assist in aerial platform operation, but do not
indicate a hazardous situation.
Operation
The aerial platform has built-in safety features and has
been factory tested for compliance with Snorkel speci-
cations and industry standards. However, any personnel
lifting aerial platform can be potentially dangerous in the
hands of untrained or careless operators.

Chapter 1 – Introduction
2 S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834
Warning
The potential for an accident increases when the
aerial platform is operated by personnel who are not
trained and authorized. Death or serious injury could
result from such accidents. Read and understand the
information in this manual and on the placards and
decals on the machine before operating the aerial
platform on the job.
Training is essential and must be performed by a quali-
ed person.
yBecome procient in knowledge and actual operation
before using the aerial platform on the job.
yThe operator must be trained and authorized to per-
form any functions of the aerial platform.
yOperation of the aerial platform must be within the
scope of the machine specications.
The operator bears ultimate responsibility for following
all manufacturer’s instructions and warnings, regulations
and safety rules of their employer and/or any state or
federal law.
Maintenance
Complete machine inspection consists of periodic visual
and operational checks, along with periodic minor adjust-
ments that assure proper performance. The frequency
and extent of periodic inspections may depend on na-
tional regulations. Daily inspection will prevent abnormal
wear and prolong the life of all systems. The inspection
and maintenance schedule should be performed at the
specied intervals and after prolonged periods of stor-
age before returning the machine to service. Inspection
and maintenance shall be performed by personnel who
are trained and familiar with mechanical and electrical
procedures.
Every person who maintains, inspects, tests, or repairs
the aerial platform must be qualied to do so. Following
the daily prestart inspection in this Operator’s Manual will
help keep the aerial platform in optimum working condi-
tion. Other maintenance functions must be performed
by maintenance personnel who are qualied to work on
the aerial platform.
Caution
Welding current can be very intense. Damage to elec-
tronic components may result. Connect the ground
clamp as close as possible to the area being welded.
Disconnect battery cables and any microprocessors
and control modules before welding on the machine.
If it becomes necessary to weld aerial platform com-
ponents as a method of repair, take all precautions to
prevent damage to electronic circuitry and devices on
the machine. This includes, but may not be limited to,
disconnecting battery cables and electronic devices.
Do not modify this aerial platform without prior written con-
sent of the Snorkel Engineering Department. Modication
may void the warranty, adversely a󰀨ect stability, or a󰀨ect
the operational characteristics of the aerial platform.
Used Material Disposal
For proper used material disposal, refer to all applicable
national and/or employer standards before disposal of
any environmentally sensitive material including, but not
limited to, hydraulic uid, batteries, and battery uid.
Manual of Responsibilities – ANSI
All owners and users of the aerial platform must read,
understand, and comply with all applicable regulations
as stated in ANSI A92.20. Ultimate compliance to ANSI
and OSHA regulations is the responsibility of the user
and their employer.
ANSI publications clearly identify the responsibilities of all
personnel who may be involved with the aerial platform.
A reprint of the “Manual of Responsibilities for Dealers,
Owners, Users, Operators, Lessors and Lessees of
ANSI/SIA A92.6-2006 Self-Propelled Elevating Work
Platforms” is available from Snorkel dealers or from the
factory upon request.
Copies are also available from:
Sca󰀨old Industry Association, Inc.
P. O. Box 20574
Phoenix, AZ 85036-0574 USA
MEWP Safe Use – AS/NZS
All owners and users of the aerial platform must read,
understand, and comply with all applicable regulations as
stated in AS/NZS 2550.10:2006. Ultimate compliance is
the responsibility of the user and their employer.
AS/NZS 1418.10 Commissioning
Per AS/NZS 1418.10, a machine has been commissioned
upon return to Snorkel of a satisfactory completed Pre-De-
livery and Inspection Record (PDIR). The PDIR inspection
is performed by Snorkel, or it’s agent, before the machine
is delivered to the customer. A completed PDIR form can
be obtained, by request, from the sales agent.
CE Compliance
The aerial work platform meets and exceeds the require-
ments of both EN280:2015+A1:2015 and ANSI A92.20.
Additional Information
For additional information contact your local dealer or
Snorkel at:
Snorkel International
P.O. Box 1160
St. Joseph, MO 64502-1160 USA
1-800-255-0317
http://www.snorkellifts.com
Regional contact information is located on the back cover
of this manual.

S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834 3
Chapter 2 – Specications
Component Identication
Scissors
Structure
Right Side
Platform
Guardrails
Left Side
Chassis
Upper
Controls
Entry
Doors
Battery Tray
Drive and Steer
Wheels
Pothole
Protector Skid
Groundstrap
Tie-Down/Lifting
Lugs
Electrical
Power Outlet
Battery Tray
Hydraulic Tray
Pump/Reservoir/Fluid Filter
Control Valve Tray
Freewheeling Valve/Brake Release Valve
Hand Pump/Diagnostic Display
Entry
Step
Toeboards
Lower
Controls
Operator’s
Manual
Battery Charger
LED Charge Indicators
Tie-Down/Lifting Lugs
Rear
Front
Forklift
Pockets
Emergency Lowering Lever
S3215L/S3215E/S3219E
Serial
Number
Power to Platform
Receptacle
Battery
Charger
Receptacle
Emergency Lowering Handle
S3220E/S3226E/S4726E/S4732E
Platform Extension
All Models Except S3215L

Chapter 2 – Specications
4 S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834
General Specications – S3215L
Aerial Platform
Working height 21′(6.6 m)
Maximum platform height 15′(4.6 m)
Turning radius
Inside 4″ (10.16 cm)
Outside 64.25″(1.63 m)
Wheelbase 52″(1.32 m)
Ground clearance
Pothole protector raised 2.63″(6.68 cm)
Pothole protector lowered 0.75″ (1.9 cm)
Maximum wheel load 980 lbs (445.5 kg)
Maximum ground bearing pressure 115 psi (8 kg/cm²)
Floor load pressure 195 psf (951 kg/m²)
Tread contact patch 8.5 in² (55.1 cm²)
Floor area 14.2 ft² (1.32 m²)
Weight, EVW
Approximate 2,100 lbs (952 kg)
Maximum allowable manual force (side pull)
Indoors 90 lbs (400 N)
Outdoors 45 lbs (200 N)
Stowed width 32″(81.3 cm)
Stowed length 81.4″(2.07 m)
With step removed 79.4″(2.02 m)
Stowed height 76″ (1.93 m)
With rails folded 65″(1.65 m)
Platform
Dimensions 28.25″x 73.5″(71.6 cm x 186.5 cm)
Guardrail height 39″ (0.99 m)
Toeboard height 6″(15.2 cm)
Rated work load
Total 670 lb (305 kg)
Maximum number of occupants 1 outdoors
2 indoors
Function Speed
Platform raise 16 to 20 seconds
Platform lower 30 to 38 seconds
High Drive
Platform lower than 6′(1.8 m)
0 to 2 mph (0 to 3.2 km/h)
Low Drive
Platform higher than 6′(1.8 m)
0 to 0.4 mph (0 to 0.6 km/h)
Drive System
Standard Two-wheel drive
Gradeability 25%
Maximum drive height 15′(4.6 m)
Drive/Lift Level Sensor Interlock
Side-to-side – ANSI 2 degrees
Side-to-side – CE/AS/NZS 1.2 degrees
Front-to-rear 4 degrees
Tires
Nonmarking solid rubber 12″x 4″(30.5 cm x 10.2 cm)
Electrical System
Voltage 24 V DC negative chassis ground
Source Four - 6 V 220 amp hour batteries
Fluid recommended distilled water
Charger 25 amp
Input 120/240 V
Hydraulic System
Maximum pressure 3,300 psi (22,750 kPa)
Reservoir capacity 3 US gal (11.35 l)
System capacity 3.5 US gal (13.2 l)
Maximum operating temperature 160°F (71°C)
Hydraulic uid recommended
Above 10°F (-12°C) ISO VG32
Below 10°F (-12°C) ISO VG15
Ambient Air Temperature Operating Range
Fahrenheit 0°F to 110°F
Celsius -18°C to 43°C
Maximum Wind Speed
Gust or steady 28 mph (12.5 m/s)
Sound Pressure Level
At work station below 70 dB(A)
Group Classication
Heavy Duty – intended life 100,000 load cycles

Chapter 2 – Specications
S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834 5
General Specications – S3215E
Aerial Platform
Working height 21′(6.6 m)
Maximum platform height 15′(4.6 m)
Turning radius
Inside 4″ (10.16 cm)
Outside 64.25″(1.63 m)
Wheelbase 52″(1.32 m)
Ground clearance
Pothole protector raised 2.63″(6.68 cm)
Pothole protector lowered 0.75″ (1.9 cm)
Maximum wheel load 1,450 lbs (659.1 kg)
Maximum ground bearing pressure 183 psi (12.8 kg/cm²)
Floor load pressure 234 psf (1141 kg/m²)
Tread contact patch 8.5 in² (55.1 cm²)
Floor area 14.2 ft² (1.32 m²)
Weight, EVW
Approximate 2,700 lbs (1227 kg)
Maximum allowable manual force (side pull)
Indoors 90 lbs (400 N)
Outdoors 45 lbs (200 N)
Stowed width 32″(81.3 cm)
Stowed length 70.4″ (1.79 m)
With step removed 68.25″(1.73 m)
Stowed height – ANSI 76″ (1.93 m)
Stowed height – CE/AS/NZS 78.75″(2 m)
With rails folded 61.5″(1.56 m)
Platform
Dimensions 28.25″x 63.75″ (71.6 cm x 161.9 cm)
Extension 28.25″x 36″ (71.6 cm x 91.4 cm)
Total length with extension 99.75″(253.4 cm)
Guardrail height – ANSI 39″ (0.99 m)
Guardrail height – CE/AS/NZS 43.3″(1.1 m)
Toeboard height 6″(15.2 cm)
Rated work load
Total 600 lb (273 kg)
Extension 250 lb (113 kg)
Maximum number of occupants 1 outdoors
2 indoors
Function Speed
Platform raise 16 to 20 seconds
Platform lower 30 to 36 seconds
High Drive
Platform lower than 6′(1.8 m)
0 to 2 mph (0 to 3.2 km/h)
Low Drive
Platform higher than 6′(1.8 m)
0 to 0.4 mph (0 to 0.6 km/h)
Drive System
Standard Two-wheel drive
Gradeability 25%
Maximum drive height 15′(4.6 m)
Drive/Lift Level Sensor Interlock
Side-to-side – ANSI 2 degrees
Side-to-side – CE/AS/NZS 1.5 degrees
Front-to-rear 4 degrees
Tires
Nonmarking solid rubber 12″x 4″(30.5 cm x 10.2 cm)
Electrical System
Voltage 24 V DC negative chassis ground
Source Four - 6 V 220 amp hour batteries
Fluid recommended distilled water
Charger 25 amp
Input 120/240 V
Hydraulic System
Maximum pressure 3,300 psi (22,750 kPa)
Reservoir capacity 3 US gal (11.35 l)
System capacity 3.5 US gal (13.2 l)
Maximum operating temperature 160°F (71°C)
Hydraulic uid recommended
Above 10°F (-12°C) ISO VG32
Below 10°F (-12°C) ISO VG15
Ambient Air Temperature Operating Range
Fahrenheit 0°F to 110°F
Celsius -18°C to 43°C
Maximum Wind Speed
Gust or steady 28 mph (12.5 m/s)
Vibration
Hand/arm less than 2.5 m/sec²
Body less than 0.5 m/sec²
Sound Pressure Level
At work station below 70 dB(A)
Group Classication
Heavy Duty – intended life 100,000 load cycles

Chapter 2 – Specications
6 S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834
General Specications – S3219E
Aerial Platform
Working height 25′(7.6 m)
Maximum platform height 19′(5.8 m)
Turning radius
Inside 4″ (10.16 cm)
Outside 64.25″(1.63 m)
Wheelbase 52″(1.32 m)
Ground clearance
Pothole protector raised 2.63″(6.68 cm)
Pothole protector lowered 0.75″ (1.9 cm)
Maximum wheel load 1,450 lbs (659.1 kg)
Maximum ground bearing pressure
175 psi (12.3 kg/cm²)
Floor load pressure – ANSI 250 psf (1221 kg/m²)
Floor load pressure – CE/AS/NZS 300 psf (1465 kg/m²)
Tread contact patch 8.5 in² (55.1 cm²)
Floor area 14.2 ft² (1.32 m²)
Weight, EVW – ANSI
Approximate 2,900 lbs (1318 kg)
Weight, EVW – CE/AS/NZS
Approximate 3,550 lbs (1614 kg)
Maximum allowable manual force (side pull)
Indoors 90 lbs (400 N)
Outdoors 45 lbs (200 N)
Stowed width 32″(81.3 cm)
Stowed length 70.4″ (1.79 m)
With step removed 68.25″(1.73 m)
Stowed height – ANSI 79.25″(2.01 m)
Stowed height – CE/AS/NZS 82.3″ (2.09 m)
With rails folded 65″(1.65 m)
Platform
Dimensions
Main 28.25″x 63.75″ (71.6 cm x 161.9 cm)
Extension 28.25″x 36″ (71.6 cm x 91.4 cm)
Total length with extension 99.75″(253.4 cm)
Guardrail height – ANSI 39″ (0.99 m)
Guardrail height – CE/AS/NZS 43.3″(1.1 m)
Toeboard height 6″(15.2 cm)
Rated work load
Total 550 lb (250 kg)
Extension 250 lb (113 kg)
Maximum number of occupants 1 outdoors
2 indoors
Function Speed
Platform raise 16 to 20 seconds
Platform lower 30 to 36 seconds
High Drive
Platform lower than 6′(1.8 m)
0 to 2 mph (0 to 3.2 km/h)
Low Drive
Platform higher than 6′(1.8 m)
0 to 0.4 mph (0 to 0.6 km/h)
Drive System
Standard Two-wheel drive
Gradeability 25%
Maximum drive height 19′(5.8 m)
Drive/Lift Level Sensor Interlock
Side-to-side – ANSI 2 degrees
Side-to-side – CE/AS/NZS 1.5 degrees
Front-to-rear 4 degrees
Tires
Nonmarking solid rubber 12″x 4″(30.5 cm x 10.2 cm)
Electrical System
Voltage 24 V DC negative chassis ground
Source Four - 6 V 220 amp hour batteries
Fluid recommended distilled water
Charger 25 amp
Input 120/240 V
Hydraulic System
Maximum pressure 3,300 psi (22,750 kPa)
Reservoir capacity 3 US gal (11.35 l)
System capacity 3.5 US gal (13.2 l)
Maximum operating temperature 160°F (71°C)
Hydraulic uid recommended
Above 10°F (-12°C) ISO VG32
Below 10°F (-12°C) ISO VG15
Ambient Air Temperature Operating Range
Fahrenheit 0°F to 110°F
Celsius -18°C to 43°C
Maximum Wind Speed
Gust or steady 28 mph (12.5 m/s)
Vibration
Hand/arm less than 2.5 m/sec²
Body less than 0.5 m/sec²
Sound Pressure Level
At work station below 70 dB(A)
Group Classication
Heavy Duty – intended life 100,000 load cycles

Chapter 2 – Specications
S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834 7
General Specications – S3220E
Aerial Platform
Working height 26′(8.1 m)
Maximum platform height 20′(6.1 m)
Turning radius
Inside 30″ (76.2 cm)
Outside 93″(2.36 m)
Wheelbase 69.72″(1.77 m)
Ground clearance
Pothole protector raised 3.75″ (9.53 cm)
Pothole protector lowered 0.75″ (1.9 cm)
Maximum wheel load 2,050 lbs (932 kg)
Maximum ground bearing pressure 215 psi (15 kg/cm²)
Floor load pressure 287 psf (1400 kg/m²)
Tread contact patch 9.6 in² (61.6 cm²)
Floor area 18.8 ft² (1.75 m²)
Weight, EVW
Approximate 4,500 lbs (2045 kg)
Maximum allowable manual force (side pull)
Indoors 90 lbs (400 N)
Outdoors 45 lbs (200 N)
Stowed width 32″(81.3 cm)
Stowed length 90.6″(2.3 m)
With step removed 88.7″(2.25 m)
Stowed height 85.25″(2.16 m)
With rails folded 67.75″(1.72 m)
Platform
Dimensions
Main 28.25″x 84.38″(71.6 cm x 214.3 cm)
Extension 28.25″x 36″ (71.6 cm x 91.4 cm)
Total length with extension 102.38″(305.8 cm)
Guardrail height 43.3″(1.1 m)
Toeboard height 6″(15.2 cm)
Rated work load
Total 900 lb (409 kg)
Extension 250 lb (113 kg)
Maximum number of occupants 1 outdoors
2 indoors
Function Speed
Platform raise 30 to 34 seconds
Platform lower 37 to 43 seconds
High Drive
Platform lower than 6′(1.8 m)
0 to 2 mph (0 to 3.2 km/h)
Low Drive
Platform higher than 6′(1.8 m)
0 to 0.4 mph (0 to 0.6 km/h)
Drive System
Standard Two-wheel drive
Gradeability 25%
Maximum drive height 20′(6.1 m)
Drive/Lift Level Sensor Interlock
Side-to-side – ANSI 2 degrees
Side-to-side – CE/AS/NZS 1.5 degrees
Front-to-rear 4 degrees
Tires
Nonmarking solid rubber 15″x 4″(38.1 cm x 10.2 cm)
Electrical System
Voltage 24 V DC negative chassis ground
Source Four - 6 V 240 amp hour batteries
Fluid recommended distilled water
Charger 25 amp
Input 120/240 V
Hydraulic System
Maximum pressure 3,300 psi (22,750 kPa)
Reservoir capacity 4.5 US gal (17 l)
System capacity 5 US gal (19 l)
Maximum operating temperature 160°F (71°C)
Hydraulic uid recommended
Above 10°F (-12°C) ISO VG32
Below 10°F (-12°C) ISO VG15
Ambient Air Temperature Operating Range
Fahrenheit 0°F to 110°F
Celsius -18°C to 43°C
Maximum Wind Speed
Gust or steady 28 mph (12.5 m/s)
Vibration
Hand/arm less than 2.5 m/sec²
Body less than 0.5 m/sec²
Sound Pressure Level
At work station below 70 dB(A)
Group Classication
Heavy Duty – intended life 100,000 load cycles

Chapter 2 – Specications
8 S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834
General Specications – S3226E
Aerial Platform
Working height 32′ (9.8 m)
Maximum platform height 26′ (7.9 m)
Turning radius
Inside 30″ (76.2 cm)
Outside 93″(2.36 m)
Wheelbase 69.72″(1.77 m)
Ground clearance
Pothole protector raised 3.75″ (9.53 cm)
Pothole protector lowered 0.75″ (1.9 cm)
Maximum wheel load – ANSI 2,050 lbs (932 kg)
Maximum wheel load – CE/AS/NZS 1,550 lbs (705 kg)
Maximum ground bearing pressure – ANSI
240 psi (16.8 kg/cm²)
Maximum ground bearing pressure – CE/AS/NZS
175 psi (12.3 kg/cm²)
Floor load pressure – ANSI 315 psf (1538 kg/m²)
Floor load pressure – CE/AS/NZS 290 psf (1416 kg/m²)
Tread contact patch 8.3 in² (53.6 cm²)
Floor area 18.8 ft² (1.75 m²)
Weight, EVW – ANSI
Approximate 5,000 lbs (2273 kg)
Weight, EVW – CE/AS/NZS
Approximate 4,500 lbs (2045 kg)
Maximum allowable manual force (side pull)
Indoors 90 lbs (400 N)
Outdoors 45 lbs (200 N)
Stowed width 32″(81.3 cm)
Stowed length 90.6″(2.3 m)
With step removed 88.7″(2.25 m)
Stowed height 90.6″(2.30 m)
With rails folded 73.13″(1.86 m)
Platform
Dimensions
Main 28.5″x 84.38″(71.6 cm x 214.3 cm)
Extension 28.25″x 36″ (71.6 cm x 91.4 cm)
Total length with extension 102.38″(305.8 cm)
Guardrail height 43.3″(1.1 m)
Toeboard height 6″(15.2 cm)
Rated work load
Total 550 lb (250 kg)
Extension 250 lb (113 kg)
Maximum number of occupants 1 outdoors
2 indoors
Function Speed
Platform raise 46 to 50 seconds
Platform lower 50 to 56 seconds
High Drive
Platform lower than 6′(1.8 m)
0 to 2 mph (0 to 3.2 km/h)
Low Drive
Platform higher than 6′(1.8 m)
0 to 0.4 mph (0 to 0.6 km/h)
Drive System
Standard Two-wheel drive
Gradeability 25%
Maximum drive height 26′ (7.9 m)
Drive/Lift Level Sensor Interlock
Side-to-side 1.5 degrees*
Front-to-rear 4 degrees
Tires
Nonmarking solid rubber 15″x 4″(38.1 cm x 10.2 cm)
Electrical System
Voltage 24 V DC negative chassis ground
Source Four - 6 V 240 amp hour batteries
Fluid recommended distilled water
Charger 25 amp
Input 120/240 V
Hydraulic System
Maximum pressure 3,300 psi (22,750 kPa)
Reservoir capacity 4.5 US gal (17 l)
System capacity 5 US gal (19 l)
Maximum operating temperature 160°F (71°C)
Hydraulic uid recommended
Above 10°F (-12°C) ISO VG32
Below 10°F (-12°C) ISO VG15
Ambient Air Temperature Operating Range
Fahrenheit 0°F to 110°F
Celsius -18°C to 43°C
Maximum Wind Speed
Gust or steady 28 mph (12.5 m/s)
Vibration
Hand/arm less than 2.5 m/sec²
Body less than 0.5 m/sec²
Sound Pressure Level
At work station below 70 dB(A)
Group Classication
Heavy Duty – intended life 100,000 load cycles
* Refer to Chapter 4 – Safety Devices, Progressive Tilt – S3226E Only.

Chapter 2 – Specications
S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834 9
General Specications – S4726E
Aerial Platform
Working height 32′ (9.8 m)
Maximum platform height 26′ (7.9 m)
Turning radius
Inside 21″ (53.3 cm)
Outside 95″(2.41 m)
Wheelbase 69.72″(1.77 m)
Ground clearance
Pothole protector raised 2.63″(6.68 cm)
Pothole protector lowered 0.75″ (1.9 cm)
Maximum wheel load 2,540 lbs (1155 kg)
Maximum ground bearing pressure
190 psi (13.3 kg/cm²)
Floor load pressure 210 psf (1025 kg/m²)
Tread contact patch 9 in² (58.1 cm²)
Floor area 27.7 ft² (2.57 m²)
Weight, EVW – ANSI
Approximate 4,750 lbs (2159 kg)
Weight, EVW – CE/AS/NZS
Approximate 4,950 lbs (2250 kg)
Maximum allowable manual force (side pull)
Indoors 90 lbs (400 N)
Outdoors 45 lbs (200 N)
Stowed width 47″(1.20 m)
Stowed length 90.6″(2.30 m)
With step removed 88.7″(2.25 m)
Stowed height 90.2″ (2.29 m)
With rails folded 72.88″(1.85 m)
Platform
Dimensions
Main 43″x 84.38″ (109.2 cm x 214.3 cm)
Extension 43″x 48″ (109.2 cm x 121.9 cm)
Total length with extension 132.38″(336.2 cm)
Guardrail height 43.3″(1.1 m)
Toeboard height 6″(15.2 cm)
Rated work load
Total 1,000 lb (455 kg)
Extension 250 lb (113 kg)
Maximum number of occupants 1 outdoors
ANSI 3 indoors
CE/AS/NZS 2 indoors
Function Speed
Platform raise 46 to 50 seconds
Platform lower 52 to 58 seconds
High Drive
Platform lower than 6′(1.8 m)
0 to 2 mph (0 to 3.2 km/h)
Low Drive
Platform higher than 6′(1.8 m)
0 to 0.4 mph (0 to 0.6 km/h)
Drive System
Standard Two-wheel drive
Gradeability 25%
Maximum drive height 26′ (7.9 m)
Drive/Lift Level Sensor Interlock
Side-to-side – ANSI 2 degrees
Side-to-side – CE/AS/NZS 1.5 degrees
Front-to-rear – ANSI 4 degrees
Front-to-rear – CE/AS/NZS 3.5 degrees
Tires
Nonmarking solid rubber 15″x 5″(38.1 cm x 12.7 cm)
Electrical System
Voltage 24 V DC negative chassis ground
Source Four - 6 V 240 amp hour batteries
Fluid recommended distilled water
Charger 25 amp
Input 120/240 V
Hydraulic System
Maximum pressure 3,300 psi (22,750 kPa)
Reservoir capacity 4.5 US gal (17 l)
System capacity 5 US gal (19 l)
Maximum operating temperature 160°F (71°C)
Hydraulic uid recommended
Above 10°F (-12°C) ISO VG32
Below 10°F (-12°C) ISO VG15
Ambient Air Temperature Operating Range
Fahrenheit 0°F to 110°F
Celsius -18°C to 43°C
Maximum Wind Speed
Gust or steady 28 mph (12.5 m/s)
Vibration
Hand/arm less than 2.5 m/sec²
Body less than 0.5 m/sec²
Sound Pressure Level
At work station below 70 dB(A)
Group Classication
Heavy Duty – intended life 100,000 load cycles

Chapter 2 – Specications
10 S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834
General Specications – S4732E
Aerial Platform
Working height 38′(11.6 m)
Maximum platform height 32′ (9.8 m)
Turning radius
Inside 21″ (53.3 cm)
Outside 95″(2.41 m)
Wheelbase 69.72″(1.77 m)
Ground clearance
Pothole protector raised 2.63″(6.68 cm)
Pothole protector lowered 0.75″ (1.9 cm)
Maximum wheel load 2,730 lbs (1241 kg)
Maximum ground bearing pressure – ANSI
325 psi (15.8 kg/cm²)
Maximum ground bearing pressure – CE/AS/NZS
245 psi (17.2kg/cm²)
Floor load pressure – ANSI 250 psf (1221 kg/m²)
Floor load pressure – CE/AS/NZS 260 psf (1269 kg/m²)
Tread contact patch 9.0 in² (58.2 cm²)
Floor area 27.7 ft² (2.57 m²)
Weight, EVW – ANSI
Approximate 5,700 lbs (2591 kg)
Weight, EVW – CE/AS/NZS
Approximate 5,925 lbs (2693 kg)
Maximum allowable manual force (side pull)
Indoors 90 lbs (400 N)
Outdoors 45 lbs (200 N)
Stowed width 47″(1.20 m)
Stowed length 90.6″(2.30 m)
With step removed 88.7″(2.25 m)
Stowed height 94.2″ (2.39 m)
With rails folded 76.88″ (1.95 m)
Platform
Dimensions
Main 43″x 84.38″ (109.2 cm x 214.3 cm)
Extension 43″x 48″ (109.2 cm x 121.9 cm)
Total length with extension 132.38″(336.2 cm)
Guardrail height 43.3″(1.1 m)
Toeboard height 6″(15.2 cm)
Rated work load
Total – ANSI 700 lb (318 kg)
Total – CE/AS/NZS 770 lb (350 kg)
Total – CE/AS/NZS Option 700 lb (318 kg)*
Extension 250 lb (113 kg)
Maximum number of occupants 1 outdoors
2 indoors
Function Speed
Platform raise 46 to 50 seconds
Platform lower 52 to 58 seconds
High Drive
Platform lower than 6′(1.8 m)
0 to 2 mph (0 to 3.2 km/h)
Low Drive
Platform higher than 6′(1.8 m)
0 to 0.4 mph (0 to 0.6 km/h)
Drive System
Standard Two-wheel drive
Gradeability 25%
Maximum drive height 32′ (9.8 m)
Drive/Lift Level Sensor Interlock
Side-to-side – ANSI 2 degrees
Side-to-side – CE/AS/NZS 1.5 degrees
Front-to-rear 4 degrees
Tires
Nonmarking solid rubber 15″x 5″(38.1 cm x 12.7 cm)
Electrical System
Voltage 24 V DC negative chassis ground
Source Four - 6 V 240 amp hour batteries
Fluid recommended distilled water
Charger 25 amp
Input 120/240 V
Hydraulic System
Maximum pressure 3,300 psi (22,750 kPa)
Reservoir capacity 4.5 US gal (17 l)
System capacity 5 US gal (19 l)
Maximum operating temperature 160°F (71°C)
Hydraulic uid recommended
Above 10°F (-12°C) ISO VG32
Below 10°F (-12°C) ISO VG15
Ambient Air Temperature Operating Range
Fahrenheit 0°F to 110°F
Celsius -18°C to 43°C
Maximum Wind Speed
Gust or steady 28 mph (12.5 m/s)
Vibration
Hand/arm less than 2.5 m/sec²
Body less than 0.5 m/sec²
Sound Pressure Level
At work station below 70 dB(A)
Group Classication
Heavy Duty – intended life 100,000 load cycles
* Refer to Serial Number placard at rear of machine.

S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834 11
Chapter 3 – Safety
Knowledge of the information in this manual, and proper
training, provide a basis for safely operating the aerial plat-
form. Know the location of all controls and how they oper-
ate to act quickly and responsibly in an emergency.
Safety devices reduce the likelihood of an accident.
yNever disable, modify, or ignore any safety device.
ySafety alerts in this manual indicate situations where
accidents may occur.
If any malfunction, hazard or potentially unsafe condition
relating to capacity, intended use, or safe operation is sus-
pected, stop aerial platform operation and seek assistance.
The operator bears ultimate responsibility for following
all manufacturer’s instructions and warnings, regulations
and safety rules of their employer and/or any state or
federal law.
Electrocution Hazards
The aerial platform is made of metal components and is
not insulated. Regard all conductors as energized. Do
not operate outside during a thunderstorm.
Minimum Safe Approach Distance – ANSI
Minimum safe approach distances to energized power
lines and their associated parts must be observed while
operating the aerial platform.
Danger
The aerial platform is not electrically insulated. Death
or serious injury will result from contact with, or in-
adequate clearance from, an energized conductor.
Do not go closer than the minimum safe approach
distance as dened by ANSI.
ANSI publications dene minimum distances that must
be observed when working near bus bars and energized
power lines. Table 1 and Figure 3 are reprinted courtesy
of Sca󰀨old Industry Association, ANSI/SIA A92.6.
Table 1 – Minimum Safe Approach Distance
Figure 3 – Minimum Safe Approach Distance
Voltage Range
(Phase to Phase)
Minimum Safe Approach Distance
Feet Meters
0 to 300V Avoid Contact
Over 300V to 50kV 10 3.05
Over 50kV to 200kV 15 4.60
Over 200kV to 350Kv 20 6.10
Over 350kV to 500kV 25 7.62
Over 500kV to 750kV 35 10.67
Over 750kV to 1000kV 45 13.72
Denotes
prohibited
zone

Chapter 3 – Safety
12 S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834
Minimum Safe Approach Distance – AS/NZS
Minimum safe approach distances to energized power
lines and their associated parts must be observed while
operating the aerial platform.
Danger
The aerial platform is not electrically insulated. Death
or serious injury will result from contact with, or in-
adequate clearance from, an energized conductor.
Do not go closer than the minimum safe approach
distance as dened by national safety regulations.
AS/NZS 2550.10:2006 dene minimum distances that
must be observed when working near overhead power
lines on poles and overhead power lines on towers. Refer
to the clearance requirements decals on the machine to
determine safe approach distances (refer to Figure 1).
Figure 1 – Minimum Safe Approach Distance
Platform Capacity
The maximum unrestricted rated load capacity and the
maximum number of occupants for the aerial platform are
stated on machine decals, placards, and in the machine
specications in this manual.
Danger
The aerial platform can tip over if it becomes unsta-
ble. Death or serious injury will result from a tip-over
accident. Do not exceed the capacity values indicated
on the machine decals, placards, and in the machine
specications in this manual.
Manual Force
Manual force is the force applied by the occupants to
objects such as walls or other structures outside the
work platform.
Danger
The aerial platform can tip over if it becomes unstable.
Death or serious injury will result from a tip-over acci-
dent. Do not exceed the maximum allowable manual
force indicated on the machine decals, placards, and
in the machine specications in this manual.
The maximum allowable manual force is limited to 45 lbs
(200 N) of force per occupant, with a maximum of 90 lbs
(400 N) for all occupants.
Wind Speeds
Do not add anything to the aerial platform that will increase
the wind loading such as billboards, banners, ags, etc.
Danger
The aerial platform can tip over if it becomes unsta-
ble. Death or serious injury will result from a tip-over
accident. Do not operate the machine in wind speeds
of 28 mph (12.5 m/s) or greater.
Do not operate the aerial platform in windy conditions
with wind gusts or steady wind speeds of 28 mph (12.5
m/s) or greater. Refer to Figure 2.
Prestart Inspection
Perform a prestart inspection before each shift as de-
scribed in Chapter 8. Do not use the aerial platform on
the job unless you are trained and authorized to do so.
Work Place Inspection and Practices
Do not use the aerial platform as a ground connection
when welding.
yThe welding ground clamp must be attached to the
same structure that is being welded.
yElectrical current ow can be very intense, causing
serious internal damage to some components.
BEAUFORT
RATING
WIND SPEED GROUND CONDITIONS
m/s km/h ft/s mph
3 3,4~5,4 12,25~19,4 11.5~17.75 7.5~12.0 Papers and thin branches move, ags wave.
4 5,4~8,0 19,4~28,8 17.75~26.25 12.0~18 Dust is raised, paper whirls up, and small branches sway.
5 8,0~10,8 28,8~38,9 26.25~35.5 18~24.25 Shrubs with leaves start swaying. Wave crests are apparent in ponds
or swamps.
610,8~13,9 38,9~50,0 35.5~45.5 24.5~31 Tree branches move. Power lines whistle. It is di󰀩cult to open an
umbrella.
713,9~17,2 50,0~61,9 45.5~56.5 31.~38.5 Whole trees sway. It is di󰀩cult to walk against the wind.
Figure 2 – Beaufort Scale