SNUGSQUARE ACE LOUNGE CHAIR User manual

ACE LOUNGE CHAIR

Gather Your Eggs...
More Eggs…
12x Split Washers
12x Flat Washers
2x Flat Washers
1x Allen Key
Note: You will also need a Phillps
Head Screwdriver, not provided
1x Back Pillow
1x Seat
Cushion
8x Long Bolts
4x Long Bolts
12x Long Bolts
2x Side Frame
1x Seat Frame
1x Wooden Brace
1x Back Frame
Note: Please retain all boxes until you are certain that your product isn’t damaged and that you
do not wish to return it. Disposal of boxes may prevent/delay our ability to resolve your request.

Step 1: Assemble the Back and Seat Frames
Before you begin, Be sure that you’re
assembling on a non-abrasive surface,
such as carpet or flattened cardboard.
To identify which is which, know that the
frame with the narrower slats is for the
back, while the frame with the wider slats is
used for the seat.
Prepare 4 short bolts by sliding on a split
washer and then a flat washer.
Place the Back frame on its side,
as shown. Lay the seat frame so
that the four corresponding holes
are prepared to line up.
Insert a bolt into each hole. Hand
tighten as you go.
Further tighten with the allen key,
but not all the way. This will come
in handy later.

Step 2: Set the First Side Frame
Position one of the Side Frames so that the
holes for the dowels are facing the ceiling.
Align the Back and Seat frames accordingly,
as shown here.
Prepare 4 dowels
Insert 2 dowels into the
Side Frame, as shown.
They should fit snugly into
their respective pockets.

Set the First Side Frame (Continued)
Align the corresponding receiving
holes on the back frame with the
dowels on the side frame, insert
dowels into receiving holes.
Taking 2 of your
prepared bolts, align
the seat frame holes
with the 2 corresponding
mounting holes on the
side frame, insert your
bolts and tighten.
Prepare 8 long bolts by sliding on a
split washer and then a flat washer.
Insert 2 of the bolts into the holes on
the back frame and tighten

Step 3: Attach the Wooden Brace
Prepare the wooden brace, two wood dowels, and one half of
the dowelling hardware, as shown above.
Slide the wooden brace onto the wood
dowels and post. Tighten the dowelling
hardware receiver onto the post with a
phillips head screwdriver.
Wooden
Dowel
Dowelling
Hardware Post
Dowelling Hardware
Receiver
Insert wooden dowels into the front leg of side frame as
shown, leaving the center hole for the post from the dowelling
hardware.
Screw the post in by hand, tighten slightly with a phillips head
screwdriver.
Take the round dowelling hardware receiver and loosen the
screw so that the through hole is clear for the post.
Insert the dowelling hardware receiver, with the through hole
perpendicular to the side and screwhead facing out, into
position on the wooden brace.

Step 4: Attach the Side Frame
Insert two wooden dowels into the back frame,
as shown above.
On the opposite end of the wood brace,
insert two wooden dowels and round
dowelling hardware.

Attach the Second Side Frame (Continued)
Insert your last 4 long
bolt and washer
combination into the
respective mounting
holes along the back
and seat frame and
tighten.
Go back and tighten the
4 bolts that connect the
back and seat frames.
Insert dowelling hardware
post into the second side
frame like the previous step.
Align and fit the receiving
holes on the side frame onto
the wooden dowels on the
brace and back frame.
With a screwdriver, tighten
the dowelling hardware on
the wooden brace just as you
did in Step 3.

DONE!
The chair is now ready to stand on all four legs.
Place the seat cushion down and then the
back cushion. Voila!
Step 5: Flip it Over and Set the Cushions