SNUGSQUARE VOSS User manual

VOSS SIDEBOARD

Gather Your Eggs...
3x Doors
2x Side Panels 2x Dividers
2x Back Panels
1x Middle Shelf
1x Top Panels
1x Bottom Panels
More Eggs...
6x Hinge Connector Hardware with 12x Screws
4x Legs with 16x Screws
1x Drill
6x Door Hinges with 12x Screws
(2x will be arced)
8x Security Screws
3x Door Handles with 6x Screws
Note: Please retain all boxes until you are certain that your product isn’t damaged and that you
do not wish to return it. Disposal of boxes may prevent/delay our ability to resolve your request.
3x Adhesive Plastic Bumpers

Step 1: Attach the Hinge Connector Hardware
Step 2: Connect the Divider Panels to the Center Shelf
Grab your side panels, divider with
mounting holes, hinge connector
hardware and matching screws.
Identify the mounting holes in the side
panel. They look like vampire bites.
Repeat for divider.
1x Center Shelf
• Check the orientation: the C-shaped groove
should face the nearest edge
• Fasten with screws
• Each side panel should have 2 hinge connectors
1x Dividers with hinge
connector attached
1x Divider

Connect the Divider Panels to the Center Shelf (Continued)
• Stand the side panels upright.
• Join the center divider with the shelf via their
corresponding slots.
• Slide the center divider into place.
Note: to ensure that the sideboard is upright
and facing forward, make sure the pins along
the center divider are o!set to the right as
shown above.

Step 3: Connect the Side Panels to the Center Shelf
2x Side Panels with hinge
connectors attached
1x Center Shelf with
Dividers in place
Stand the side panels with the pins facing up.
Stand the shelf so that the slotted edge is resting
on the floor.
Once inserted, slide the side panel so that the pins lock into place and the edges
are flush. Repeat on the other side.
Bring the two pieces together so that the pins
along the shelf fit into the keyholes located on
the side panel.

Step 4: Attach the Bottom Panel, Back Panels
and Top Panel
1x Top Panel
2x Back Panels
1x Bottom Panel
• Hook the bottom panel onto the pins.
Slide into place.
• Make sure the edges are flush

Step 5: Attach the Back Panels
• Hook the top panel onto
the pins.
• Slide into place.
Lay the Sideboard face down so that the pins
are facing up.
Note: Attach the lower back panel first. Use the
center divider’s o! set pins to di! erentiate top
from bottom
• Lay the lower back panel so that the keyhole
slots line up with the pins
• Slide the panel to lock the pins into place
• Repeat for the upper
back panel

Step 6: Secure the Bottom Panel and Attach the Legs
• Locate the 8 holes in the bottom panel
• Make sure the edges are flush
• Using the security screws, fasten the
bottom panel
Repeat for remaining legs
Flip the Sieboard onto its feet
Attach the legs using the leg screws. There are
4 screws to each leg.
Note: flared legs should each point outward
towards their respective corners.

Step 7 : Install the Hinges
6x Door Hinges with 12x Screws
Place a hinge into each well on the inside of
the door panel.
Arced Hinge
Insert a screw into each mounting hole and
fasten. Repeat for the remaining hinges.
Note: Two of the hinges have an arc. The arced
hinges will be used for the center door.
Straight Hinge

Step 8: Attach the Doors
Step 9: Attach the Door Handles
Rest the hinges over their receiving hardware. Make sure the doors are right-side up.
Press the hinges into the hardware. They should just snap into place. See below.
Push end down onto
receiving hardware and
snap in place.
Insert the mounting screws from the
inside of the door. Fasten to the handle
on the other side.
Slide hinge up against
receiving hardware.

Step 10: Adjust the Hinges and Center the Doors
Adjustment 1: Move door to the left or right of the side panel.
Moves door left and right
Moves door left and right
Moves door
back and forth
Moves door up/down
• Hinges are adjustable in 3 di! erent locations.
• Each adjusts the position of the doors di ! erently.
• Note the locations indicated in the image
TIPS:
• Coordinate your adjustments for top and bottom hinges
• Begin by maxing out each adjustment point
• Use manual screwdriver for fine-tune adjustments.
Use this adjustment to:
• Ensure a vertical center gap between doors
• Widen or narrow the center gap.
Note: The gap between the doors will taper, or slant, if the
top and bottom hinges are not equally adjusted
Door is adjusted too far to the right of
the side panel. This creates a larger gap
between the two doors.
Door is adjusted too far to the left of the
side panel. This creates a smaller gap
between the two doors

Adjustment 2: Move the door closer or farther away from the side panel.
Adjustment 3: Move the door up or down.
Use this adjustment to:
• Make the edges of the door parallel with the edges of the sideboard.
• Widen or narrow the gap between the doors and sideboard.
Note: Check that the gap between the open door and side panel is
vertical and does not taper.
Use this adjustment to ensure that the doors are flush with the top
and bottom panels.
Tip: Leave the screws tight enough to hold the door in place, but
loose enough to remain adjustable.
Moves door
back and forth
Moves door up/down
Door is adjusted to be farther away
from sideboard.
Door is adjusted down and sits below
the top edge of the sideboard
Door is adjusted up and sits above
the top edge of the sideboard.
Door is adjusted to lose to the sideboard.

DONE!
Step 11: Add Plastic Bumpers
Stick a small plastic bumper to the top corner of
each door. This will help with door adjustment