SNUGSQUARE JORN DESK User manual

JORN DESK

Gather Your Eggs...
Base Desk Parts
20x Long Bolts
4x Washers
Left Leg
Back
Lower Shelf
Desk Top
Right Leg
Note: Please retain all boxes until you are certain that your product isn’t damaged and that you
do not wish to return it. Disposal of boxes may prevent/delay our ability to resolve your request.
Drill + Extension
Hex Bit with Ball End

More Eggs...
Optional Parts
(Parts included based on options chosen)
Left Pedestal Right PedestalLong Shelf
Monitor Stand
Brackets + Thumb
Screws & T-Slot Nuts
Note:
Number of Thumb Screws,
T-slot nuts and short bolts
vary depending on set-up.
Short Bolts
Plastic Dots
(2 Per Bracket)

Step 1: Attach the Legs
Place the Desk Top upside
down on a soft surface to
protect from scratches.
Take your first leg and make sure that the pockets of the leg are facing
towards the center of the desk and the angled part of the leg is facing
towards the front.
Slot the top of the leg into the receiving pocket on the the Desk Top
making sure that the holes align with the leg pockets.
Next insert a bolt and washer into each of the leg pockets and fasten to
the top using the provided drill and hex bit attachment.

Step 2: Install Second Leg
Repeat previous instruction
for the other leg

Step 3: Attach Back Panel
Place the back panel down with the
pockets facing up.
Rotate the desk top onto the back panel
So that it slots in below the top tabs.
The pockets on the desk top will align with
the top row of holes on the back panel.
The pockets on the back panel will align
with the hole on the legs.
Insert 6 bolts and fasten
the desk top and legs to
the back panel.

Step 4: Attach the Lower Shelf
Step 5: Turn Desk Upright
This completes the assembly of
the base desk. The next section
will discuss the attachments
Next take your bottom shelf, with pockets
facing towards the bottom of the legs, and
align the pockets with the holes on the back
panel and the legs. Insert bolts (4 for the
back panel, 3 for each leg) in the pockets
and fasten the shelf into place.

Step 6: Attachment Options
Left Pedestal Right PedestalLong Shelf
Brackets + Thumb
Screws & T-Slot
Nuts
Monitor Stand
The desk comes with di!erent options.
Your desk will include the parts you need
for the option you chose at checkout.
The assembly for any option is the same.
Short Bolts

Step 6: Attachment Options (Continued)
First choose the height you would like your
shelves to be. There are 2 options, either
use the 2 top holes, or the 2 bottom holes.
Next, insert 2 thumb screws through your
selected holes on the bracket.
Take your t-slot nuts and place them onto
your screws and turn them once. With
the long side of the nuts parallel to the
ground insert the nuts and screws into the
slots on the back panel.
With the bracket in position, slowly tighten
the thumb screws, the t-slot nut should
rotate slightly so that it is perpendicular to
the ground.
Once it is perpendicular, fully tighten the
screws. Repeat for all shelves.
IMPORTANT! Your t-slot
nuts should look like
this, failure to attach
correctly could result in
your shelf failing.
view from the inside
T-Slot Nut

Step 7: Add Your Shelf Option
Insert the bolts through the brackets
into the shelf and tighten.
Shelf can be adjusted forwards or
backwards to your desired distance.
If your shelves do not sit level at 90
degress, we have included sticky
plastic dots to help level them out.
Place the dots on either side of the
slot towards the front end of the
bracket. If you need to adjust the
angle, you can reposition them on the
bracket moving towards the mounting
bolt to increase the shelf angle
or away from the mounting bolt to
decrease the shelf angle.
lastic ots

DONE!