Socket Bluetooth iPAQ User manual

Socket
Bluetooth®Cordless Hand Scanner
Series 7 and Series 7 Rx
User’s Guide

7/2010 Document # 6410-00233 AA
COPYRIGHT NOTICE
Copyright © 2004-2010 Socket Mobile, Inc. All rights reserved.
Socket, the Socket logo, Battery Friendly, Socket Bluetooth Cordless Hand Scanner,
SocketCare, SocketScan, Mobility Friendly, Connect!Agent, SoMo, ActivePairing and
Error Proof Protocol are trademarks or registered trademarks of Socket Mobile, Inc.
Bluetooth and the Bluetooth logos are registered trademarks owned by Bluetooth
SIG, Inc., U.S.A. and licensed to Socket Mobile, Inc. All other brand and product
names are trademarks of their respective holders.
The Socket Bluetooth Cordless Hand Scanner includes technology licensed under
United States Patent Numbers 5,902,991, 7,429,000 B1 and D526,320 S.
Reproduction of the contents of this manual without the permission of Socket
Mobile is expressly prohibited. Please be aware that the products described in this
manual may change without notice.
Feel free to contact Socket Mobile at:
Socket Mobile, Inc.
39700 Eureka Drive
Newark, CA 94560-4808
USA
Other than the above, Socket Mobile can assume no responsibility for anything
resulting from the application of information contained in this manual.
Please refrain from any applications of the Socket Bluetooth Cordless Hand Scanner
that are not described in this manual. Please refrain from disassembling the
Bluetooth Cordless Hand Scanner. Disassembly of this device will void the product
warranty.
You can track new product releases, software updates and technical bulletins by
visiting the Socket Mobile website at: http://www.socketmobile.com.

IMPORTANT!
The information in this User’s Guide is based on version 2 or later of
the Socket Bluetooth Cordless Hand Scanner (CHS) hardware, which
includes devices with any of the following part numbers:
Bluetooth CHS version Part Number
7E 8550-00056
7E2 8550-00050
8550-00051
8550-00052
7M 8550-00038
8550-00041
8550-00057
7M2 8550-00053
7P 8550-00039
8550-00058
7NRx 8550-00046
The features described in this manual that do not apply to older hardware versions of
the Socket Bluetooth Cordless Hand Scanner will be noted as such.
If you have a version of the CHS 7X or 7XRx that supports only Bluetooth® Human
Interface Device (HID) profile, please refer to the appropriate user’s guide at:
http://www.socketmobile.com/pdf/data-collection/chs-7x_ug.pdf

4
TABLE OF CONTENTS
COPYRIGHT NOTICE 2
1 | INTRODUCTION 5
SCANNER VERSIONS 5
ABOUT THE SOFTWARE 5
PACKAGE CONTENTS 6
SYSTEM COMPATIBILITY REQUIREMENTS 6
PRODUCT REGISTRATION 7
SOCKETCARE™SERVICE PROGRAM 7
ACCESSORIES 7
ADDITIONAL DOCUMENTATION 7
HARDWARE FEATURES 8
2 | HARDWARE PREPARATION 10
INSTALLING BATTERIES AND ATTACHING THE TETHER 10
ASSEMBLING THE AC ADAPTER 12
CHARGING THE SCANNER 12
3 | SETUP FOR WINDOWS 7, VISTA, AND XP 13
4 | SETUP FOR THE SOMO 650 36
5 | SETUP FOR WINDOWS MOBILE 51
6 | SETUP FOR PALM OS 68
7 | SETUP FOR RIM BLACKBERRY 78
8 | SETUP FOR NOKIA 85
APPENDICES
A SPECIFICATIONS 92
B SAFETY AND USAGE TIPS 95
C BARCODE LABEL SPECIFICATIONS 97
D DECODE ZONE 98
E RESTORING FACTORY DEFAULTS 100
F CHANGING THE DATA MODE 101
G TROUBLESHOOTING 103
H TECHNICAL SUPPORT 107
LIMITED WARRANTY 108
REGULATORY COMPLIANCE 110

CHAPTER 1: INTRODUCTION 5
1 | INTRODUCTION
Thank you for purchasing the Socket Bluetooth
Cordless Hand Scanner (Bluetooth CHS) Series 7.
The Socket Bluetooth CHS combines the power of
barcode scanning with the convenience of
Bluetooth wireless technology so you can collect
barcoded data without being tied to your mobile
or desktop computer. Compact, lightweight, and
ergonomically designed to fit comfortably in a
hand, the Socket Bluetooth CHS is ideal for high
volume data collection applications.
SCANNER VERSIONS
Model Scanning Engine Rugged
Case
Made with
Antimicrobial Materials
7E2 Class 1 Laser – 1D No No
7M2 Class 2 laser – 1D No No
7P Class 2 Laser – 1D Yes No
7X CMOS – 1D & 2D Yes No
7NRx Class 1 Laser – 1D Yes Yes
7XRx CMOS – 1D & 2D Yes Yes
ABOUT THE SOFTWARE
SocketScan™enters scanned data directly into any program as if
the data were manually typed. Included is a utility for configuring
Prefix/Suffixes, sounds, ActivePairing, and other special settings
for the Socket Bluetooth CHS.
Connect!Agent™software automates Bluetooth by setting up and
managing the wireless connection (Windows Mobile only).
ActivePairing™enables you to connect to a specific host computer by scanning
a special barcode or setting up a “Permanent Pair.” (Windows only, requires
Socket Bluetooth CHS v2)
Error Proof Protocol™ensures reliability of data collection by confirming in
real time that scanned data has reached the host computer. This minimizes the
risk of data loss from a dropped connection.
Download the latest Socket software free from:
http://www.socketmobile.com/support/downloads/

6
PACKAGE CONTENTS
Socket Bluetooth
Cordless Hand Scanner
AC adapter with plugs for
USA, Europe, Australia
2 NiMH rechargeable
AAA batteries
Lanyard with
retractable tether
CD with software and
documentation
Charging Cradle
(Series 7 Rx only)
SYSTEM COMPATIBILITY REQUIREMENTS
Note: The CHS 7X and 7XRx versions with support for Serial Port Profile (SPP)
are only compatible with Windows 7, Vista, XP, Mobile, and RIM BlackBerry OS
in SPP mode. To connect to Palm or Symbian smartphones, use HID mode,
covered in a separate manual. http://www.socketmobile.com/pdf/data-
collection/chs-7x_ug.pdf
Windows 7, Vista, XP:
•Bluetooth radio
•Bluetooth stack from Microsoft, Toshiba or Broadcom
Windows Mobile:
•Any of the following Windows Mobile versions:
−Windows Mobile 6 Classic/Professional
−Windows Mobile 2003, 2003SE or 5.0 for Pocket PC/Pocket PC Phone
•Bluetooth radio
•Either of the following Bluetooth stacks:*
−Broadcom 1.5 or later
−Microsoft Bluetooth stack for Windows Mobile
−Stonestreet One 1.2.4 (Build 1783)
•Software installation requires a PC with ActiveSync or Windows Mobile
Device Center software (free from Microsoft website).
Palm OS:
•Palm OS 5.2 or later
•Bluetooth wireless technology

CHAPTER 1: INTRODUCTION 7
•Software installation requires a PC running Palm Desktop Software.
RIM BlackBerry: The Socket Bluetooth CHS Series 7 is compatible with the
BlackBerry Curve 8200, 8300; Pearl 8100; Bold 9000, 8600, 9700; Storm 9500;
and Tour 9600 series smartphones.
Symbian OS: The Socket Bluetooth CHS Series 7 is compatible with the Nokia
E61, E61i and E71 smartphones.
Windows CE.NET: The Socket Bluetooth CHS Series 7 is compatible with the
Intermec CK30. For instructions, contact technical support at:
http://support.socketmobile.com
PRODUCT REGISTRATION
Socket highly recommends that all customers register their products. Registered
users receive priority for technical support and can choose to obtain special
offers, upgrades, and new product information. Register online at:
http://support.socketmobile.com
SOCKETCARE™SERVICE PROGRAM
SocketCare is an enhanced service program that supports deployments of the
Bluetooth CHS with faster technical support, faster repair and replacement, and
the option for full coverage. For more information, please visit:
http://www.socketmobile.com/socketcare
ACCESSORIES
Accessories available for the Socket Bluetooth CHS include:
•Charging cradle (standard and antimicrobial versions)
•Car charger
•Scanning Companion USB Bluetooth adapter
•Mobile Power Pack (available in Americas and Asia Pacific)
For more information, please visit:
http://www.socketmobile.com/products/bluetooth-barcode-
scanners/accessories/
ADDITIONAL DOCUMENTATION
Socket has also published Quick Start Guides and an Advanced Programming
Guide. Download them online at:
http://www.socketmobile.com/support/downloads/
For the 7X or 7XRx (2D and 1D) versions, please refer to the appropriate
User’s Guide at: http://www.socketmobile.com/pdf/data-collection/chs-
7x_ug.pdf

8
HARDWARE FEATURES
Product Diagram
Rechargeable Batteries and AC Adapter
Charge the internal batteries by using the AC adapter or charging cradle, if
included. The adapter rating is 5V, 2A, positive pole center. New, fully
charged batteries last ~19 hours to scan 15,000+ barcodes. The power jack fits
a 4mm barrel connector.
WARNING: Charge ONLY NiMH batteries in the Bluetooth CHS. Damage may
result if other battery types are charged. Do not store the Bluetooth CHS for
more than 30 days with the batteries installed.
The red Battery Status LED will not function properly if standard AAA non-
rechargeable batteries are being used.
Besides the included AC adapter, you can also recharge the Bluetooth CHS
by using any of the following:
•Socket charging cradle for the Socket Bluetooth CHS
•Socket car charger
•Socket Mobile Power Pack (sold in Americas and Asia Pacific)
•AC and DC adapters of the Socket SoMo®650 handheld computer, as well
as those of most recent Pocket PCs from Casio, Fujitsu, HP, and Toshiba
Socket charging accessories are available online at:
http://www.socketmobile.com/products/bluetooth-barcode-
scanners/accessories/
Trigger button
Power button
Stylus tip
Status indicator LED
Scanner
window
Battery cover

CHAPTER 1: INTRODUCTION 9
The LED and beep behaviors below are for the Bluetooth CHS v2.
Status Indicator LED
LED LED Activity Meaning
1 blink per second Bluetooth radio is on, but not connected.
Bluetooth
Status
(Blue)
1 blink per 3 seconds Scanner connected to computer
Good Read
(Green)
On Data successfully scanned and transmitted
to host device.
Blinking 20% battery capacity remaining
Battery
Status
(Red) Off Off or Good Battery status
Status Indicator Beeps
Beep Pattern Meaning
2 beeps (low-high) Power on
2 beeps (high-low) Power off
1 beep Scanner connected to computer
2 beeps
(same tone) Scanner disconnected from computer
2 long beeps
(same tone) with
Permanent Pairing
enabled
Scanner unsuccessfully tried 20 times to connect to the
device assigned as its Permanent Pair
1 beep with green
LED (optional
setting)
Data successfully scanned and sent to computer
Touch Screen Stylus
The Socket Bluetooth CHS features a stylus tip in the tail
of the Bluetooth CHS that you can use on Pocket PC and
other device touch screens.
WARNING: Do not use the stylus if damaged. A
damaged stylus may scratch the display screen of
your computer.
Note: The stylus does not work with tablets using Active Matrix displays.

10
2 | HARDWARE PREPARATION
INSTALLING BATTERIES AND ATTACHING THE TETHER
1. Use a coin or screwdriver to unlock and remove the battery cover. Turn
the lock underneath the scanner to a horizontal position to unlock.
2. Remove the battery cover.
For the Bluetooth CHS v2, the Bluetooth Device Address is printed
on a label inside the battery compartment. The address is used to
identify the Bluetooth CHS.
3. If desired, attach the tether. Wrap the string loop around the inside part
of the lock.

CHAPTER 2: HARDWARE PREPARATION 11
4. Install the batteries as indicated by the +/- symbols.
WARNING: Do not install the batteries incorrectly.
Damage may result.
5. Replace the battery cover and turn the lock to a vertical position to
secure it.
6. If desired, attach the tether to a lanyard or belt.

12
ASSEMBLING THE AC ADAPTER
The AC adapter included with the Bluetooth CHS includes four international
plugs. Simply find the correct plug for your region and slide it into the head
of the adapter.
CHARGING THE SCANNER
Use the AC adapter or charging cradle, if included, to charge the Bluetooth
Cordless Hand Scanner. Alternatively, you can use a car charger or the
Mobile Power Pack (all available separately).
The scanner must be fully charged before its first use. The LED will emit a
solid red light while charging, and turn green when the batteries are fully
charged.
WARNING: Do not attempt to charge alkaline batteries —
this may cause alkaline batteries to leak and damage the
Bluetooth CHS.
The red Battery Status LED will not work properly if standard AAA
alkaline batteries are being used.
To purchase charging accessories, please visit:
http://www.socketmobile.com/products/bluetooth-barcode-
scanners/accessories/

CHAPTER 3: SETUP FOR WINDOWS XP, VISTA, AND 7 13
3 | SETUP FOR WINDOWS 7, VISTA,AND XP
This chapter explains how to install and use the
Bluetooth Cordless Hand Scanner (Bluetooth CHS)
with a Bluetooth enabled computer running
Windows 7, Vista or XP
Before you begin the instructions in this chapter, make sure you have
installed the batteries and charged the scanner, as described in Chapter 2,
“Hardware Setup.”
CONNECTION OPTIONS
For Windows-based computers, the Socket Bluetooth CHS offers three different
connection options to fit different work environments.
Scenario How the Bluetooth
Connection Initiates
Pros/Cons Compatible
Hardware/
Scenario 1: Single
user with one scanner
per PC, no roaming.
Computer initiates the
connection through
Bluetooth software.
Easiest to configure
but requires user to
start connection
through software.
Any version of
Bluetooth CHS
Scenario 2:
Enterprise deployment
with one scanner per
PC, no roaming.
Scanner initiates the
connection automatically
when it is powered on.
(ActivePairing with
Permanent Pair)
More complex to
configure but
easiest connection
method.
Scenario 3: Enterprise
deployment with
scanner(s) roaming
between different PCs.
Scanner initiates the
connection by reading a
special barcode.
(ActivePairing)
Easy to connect but
requires barcode
generating
software and
printer.
Part Number
(labeled in
battery
compartment)
8550-00037 or
later
IMPORTANT! REMEMBER THE NUMBER OF THE SCENARIO YOU WANT
TO SET UP THE SOFTWARE FOR!
Note: ActivePairing has been successfully tested with the Microsoft, Broadcom
and Toshiba Bluetooth stacks. Due to the many possible hardware manufacturer
and Bluetooth stack combinations, ActivePairing may not work correctly on all
computers running Windows XP, Vista or 7.

14
STEP 1: UNINSTALL OTHER SCANNING SOFTWARE
Uninstall any barcode scanning software already installed in your computer,
including previous versions of SocketScan.
1. Make sure the software is not running.
2. Make sure you are logged into an administrative account.
3. Click Start | Control Panel.
•For Windows 7, click Uninstall a program.
•For Windows Vista, click Programs and Features.
•For Windows XP, click Add or Remove Programs.
4. Use the utility to remove the software.
STEP 2: INSTALL THE SOFTWARE
Note: Download the latest software free from:
http://www.socketmobile.com/support/downloads
1. Make sure you are logged into an administrative account, otherwise you
will not have permission to install software and/or the software will not
install correctly.
2. Insert the SocketScan installation CD into the CD drive of your PC. Use My
Computer or Windows Explorer to access your CD drive. In the CD,
click on SETUP.EXE.
3. The SocketScan Setup Center will appear in your web browser. Read the
first page and click Installation in the left margin.
4. In the SocketScan Installation page, scroll down to the Windows XP and
Windows Vista section and click on the Install link there.

CHAPTER 3: SETUP FOR WINDOWS XP, VISTA, AND 7 15
5. Your web browser will present a series of dialogs.
Internet Explorer:
•In the File Download –Security Warning dialog, click Run.
•In the second warning dialog, click Run.
Firefox:
•In the file opening dialog, click Save File.
•Firefox will download the file.
•In the Downloads list, next to SocketScan...exe, click Open.
•In the warning dialog, click OK to continue.
6. The installation wizard will launch. Follow itto install the software.
7. During installation, a message may warn that the software is unsigned or
has not passed Windows Logo testing.
3
•Windows Vista: Click Install this driver software anyway.
•Windows XP: Click Continue Anyway.
8. After software installation, restart your computer.
9. Icons for SocketScan and Socket CS Connect will appear on your
desktop.

16
STEP 3: TURN ON THE BLUETOOTH CHS
Press and hold the small power button for 3 seconds, until the LED turns
blue and the scanner beeps twice (low-high). The LED should blink blue once
per second to show that the Bluetooth radio is on but not connected.
After the scanner is turned on, its Bluetooth mode will change over time if no
connection is made.
Note: This Bluetooth mode sequence is for the Bluetooth CHS v2.
Time after turning on scanner Bluetooth mode
0-5 minutes Discoverable and connectable
5-20 minutes Connectable
20 minutes Scanner automatically powers off
STEP 4: START BLUETOOTH ON YOUR COMPUTER
Note: Refer to your Bluetooth hardware/software documentation for full
instructions.
1. If using an add-on Bluetooth card or adapter, such as the Socket Scanning
Companion USB adapter, plug it into your computer.
2. Start your computer’s Bluetooth software. For some computers, the Bluetooth
software will automatically launch after you turn on the Bluetooth radio.
3. Turn on the Bluetooth radio. For some computers, the Bluetooth radio must be
enabled through the software. Other computers have a hardware switch.
Note: Your Bluetooth software may vary from the screen shown.

CHAPTER 3: SETUP FOR WINDOWS XP, VISTA, AND 7 17
STEP 5: CONFIGURE BLUETOOTH SETTINGS
Follow the appropriate instructions for your Bluetooth stack. Configuration
is only needed the first time you connect the Bluetooth CHS to your PC.
Refer to your Bluetooth software manual for full instructions.
SocketScan supports a generic Bluetooth COM port and may be able to
connect to Bluetooth stacks other than those listed.
Microsoft Bluetooth Stack:
1. Right-click on the Bluetooth icon in the task tray. In the pop-up menu,
click Add a Bluetooth Device for Windows XP/Vista or Add a Device
for Windows 7.
2. The Add Bluetooth Device Wizard will start.
-Windows 7: Your computer will automatically begin searching for
Bluetooth devices in range and report found devices.
-Windows XP or Vista: A welcome screen will appear. Check the box My
device is set up and ready to be found. Click Next.
3. After the search, select Socket CHS [xxxxxx]. Click Next.
Note: The characters in brackets are the last 6 characters of the scanner’s
Bluetooth Device Address, which is labeled inside the battery compartment
for the Bluetooth CHS v2.
4. A passkey or pairing option screen will appear.
-Windows 7: Select Enter the device’s pairing code and enter the
default PIN 1234. Click Next.
-Windows XP or Vista: Select Use the passkey found in the
documentation and enter the default PIN 1234. Click Next.
5. Your computer will connect to the scanner. Status balloons will appear,
reporting the connection progress. After connecting, the Bluetooth CHS
will beep once, and the LED will blink blue once every 3 seconds.

18
6. Complete the wizard and note the necessary COM port number(s):
IMPORTANT!
•FOR SCENARIO 1, NOTE THE OUTGOING COM NUMBER.
•FOR SCENARIO 2, NOTE BOTH COM NUMBERS.
•FOR SCENARIO 3, NOTE THE INCOMING COM NUMBER.
•Windows 7: At the end of the wizard, click Close. To determine your
COM ports, click on the Bluetooth task tray icon. In the pop-up menu,
click Open Settings. Click on the COM Ports tab.
•Windows XP/Vista: In the last screen of the wizard, note the COM port
number(s) and click Finish.

CHAPTER 3: SETUP FOR WINDOWS XP, VISTA, AND 7 19
Toshiba Bluetooth Stack:
1. Double-click on the Bluetooth icon at the bottom of your screen.
2. In Bluetooth Settings, tap New Connection.
3. The Add New Connection Wizard will launch. Select Custom Mode and
click Next. The tablet will search for Bluetooth devices in range.
4. In the list of devices, select Socket CHS [xxxxxx]. Click Next.
Note: The characters in brackets are the last 6 characters of the scanner’s
Bluetooth Device Address, which is labeled inside the battery compartment
for the Bluetooth CHS v2.
5. If a passkey is requested, enter the default PIN 1234. Click OK. To indicate
the connection, the Bluetooth CHS will beep once.
6. In the list of device services, select Serial Port. Click Next.

20
7. In the next screen, uncheck Use default COM port. Click Next.
8. The software will report that the default setting is recommended. Click OK.
9. Select another COM port. If desired, check Auto Connect. Click Next.
WARNING! Do not select a COM port used by another device on your
system!
IMPORTANT! FOR SCENARIO 1 OR 2, REMEMBER WHICH COM NUMBER
YOU CHOSE! THIS IS THE LOCAL COM-CLIENT PORT NUMBER.
10.After COM port selection is complete, remember the COM port number
(it is the Local COM-Client port number). Click Next.
11.Edit the connection name and/or icon if desired. Click Next.
12.In the last screen, click Finish.
13.For Scenario 2 or 3, check the Local COM-Server port number.
Click Start | Control Panel | Bluetooth Local COM.
IMPORTANT!
•FOR SCENARIO 1, NOTE THE LOCAL COM-CLIENT NUMBER.
•FOR SCENARIO 2, NOTE BOTH COM PORT NUMBERS.
•FOR SCENARIO 3, NOTE THE LOCAL COM-SERVER NUMBER.