socomec ATyS g M User manual

Automatic Transfer Switching Equipment
ATySgM
INSTALLATION AND OPERATING MANUAL EN

ATySgM - 542933D - SOCOMEC
2EN
1. GENERAL SAFETY INSTRUCTIONS ...........................................................4
2. INTRODUCTION .............................................................................5
2.1. The ATyS family product range..............................................................5
2.2. The ATyS M Range Key Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.2.1. Selection guide .....................................................................7
3. QUICK START ...............................................................................8
3.1. Quick Start ATySgM (2P) .................................................................8
3.2. Quick Start ATySgM (4P) ................................................................12
4. ATYSGM VERSIONS .......................................................................15
4.1. Product presentation .....................................................................15
4.2. Specifications and advantages.............................................................15
4.3. Supply types............................................................................15
5. OPTIONAL ACCESSORIES ..................................................................16
6. TECHNICAL DATA ..........................................................................17
7. ENVIRONMENTAL CONDITIONS .............................................................18
8. PRODUCT INSTALLATION ...................................................................19
8.1. Changing the padlocking configuration......................................................19
8.2. Recommanded orientation ................................................................19
8.3. Dimensions of the single phase ............................................................19
8.4. Back plate mounted single phase ..........................................................19
8.5. Dimensions of the three phase.............................................................20
8.6. Back plate mounted three phase...........................................................20
8.7. DIN rail mounted ........................................................................20
9. INSTALLATION OF OPTIONAL ACCESSORIES .................................................21
9.1. Auxilliary contacts .......................................................................21
9.2. Voltage sensing and power supply tap .....................................................21
9.3. Bridging bars 2P ........................................................................21
9.4. Bridging bars 4P ........................................................................22
9.5. Terminal shrouds ........................................................................22
9.6. Sealable cover ..........................................................................22
10. INSTALLING WITHIN THE ATYSM ENCLOSURE ..............................................23
10.1. Modular plastic enclosure................................................................23
10.2. Polycarbonate enclosure ................................................................24
10.2.1. Wiring in a polycarbonate enclosure .................................................24
10.2.2. Extension unit ...................................................................24
EN CONTENT

ATySgM - 542933D - SOCOMEC 3EN
11. CONNECTION OF THE POWER CIRCUITS ...................................................25
11.1. Ratings / cross-sections table of correspondence ...........................................25
11.2. Parallel pole set-up for a 4P device used in single phase .....................................25
11.3. Network configurations ..................................................................26
11.3.1. 230VAC network configurations (2P) .................................................26
11.3.2. Configurations réseau 230/400VAC (4P) .............................................26
11.3.3. Configurations réseau 127 / 230VAC ................................................27
11.3.4. Three phase without neutral network.................................................28
11.3.4.1. Auto-transformer connections..............................................28
11.3.4.2. Procedure for the configuration and storage of the neutral position. .................29
11.3.4.3. Reset of neutral position ..................................................29
12. CONNECTION OF CONTROL/COMMAND CIRCUITS ..........................................30
12.1. Terminal connectors designation ..........................................................31
12.2. Auxiliary contact operating schedule.......................................................32
13. OPERATION...............................................................................33
13.1. Presentation of the product interface ......................................................33
13.1.1. 2P product interface...............................................................33
13.1.2. 4P product interface...............................................................33
13.1.3. Reset ...........................................................................34
13.2. Manual mode ..........................................................................34
13.2.1. Manual switching .................................................................34
13.3. Padlocking ............................................................................35
13.4. Programming ..........................................................................36
13.4.1. Single phase versionw .............................................................36
13.4.2. Three phase version...............................................................37
13.4.3. Sealable configuration cover ........................................................38
13.5. Automatic mode .......................................................................38
13.5.1. Sealable Auto/Manual cover ........................................................38
13.6. Possible actions ........................................................................38
13.7. Manual & Automatic Mode / Mains restoration conditions.....................................39
13.7.1. Mode 1: Automatic retransfer .......................................................39
13.7.2. Mode 2a: Controlled retransfer ......................................................41
13.7.3. Mode 2b: Controlled transfer .......................................................43
13.7.4. Mode 3: Network - Network application with priority ...................................44
13.7.5. Mode 4: Network - Network application without priority.................................47
14. PREVENTATIVE MAINTENANCE .............................................................49
15. TROUBLESHOOTING GUIDE ...............................................................50

ATySgM - 542933D - SOCOMEC
4EN
1. GENERAL SAFETY INSTRUCTIONS
• This manual provides instructions on safety, connections and operation of the ATySM transfer switch manufactured by
SOCOMEC.
• Whether the ATyS is sold as a loose product, as a spare, as an enclosed solution or as any other conguration,
this device must always be installed and commissioned by qualied and experienced personnel, in line with the
manufacturers recommendations, following good engineering practices and after having read and understood the
details in the latest release of the relative product instruction manual.
• Maintenance on the product and any other associated equipment including but not limited to servicing operations must
be performed by adequately trained and qualied personnel.
• Each product is shipped with a label or other form of marking including rating and other important specic product
information. One must also refer to and respect markings on the product prior to installation and commissioning for
values and limits specic to that product.
• Using the product outside the intended scope, outside SOCOMEC recommendations or outside the specied ratings
and limits can cause personal injury and/or damage to equipment.
• This instruction manual must be made accessible so as to be easily available to anyone who may need to read it in
relation with the ATyS.
• The ATyS meets the European Directives governing this type of product and includes CE marking on each product.
• No covers other than that for auto/manu on the ATyS should be opened (with or without voltage) as there may still be
dangerous voltages inside the product such as those from external circuits.
• Do not handle any control or power cables connected to the ATyS when voltage may be present on the
product directly through the mains or indirectly through external circuits.
• Voltages associated with this product may cause injury, electric shock, burns or death. Prior to carry out any
maintenance or other work on live parts or other parts in the vicinity of exposed live parts, ensure that the switch
including all control and associated circuits are de-energized.
DANGER WARNING CAUTION
RISK:
Electric shock, burns, death
RISK:
Possible personal injury
RISK:
Equipment damage
• As a minimum the ATySM comply with the following international standards:
- IEC 60947-6-1
- GB 14048-11
- EN 60947-6-1
- VDE 0660-107
- BS EN 60947-6-1
- NBN EN 60947-6-1
- IEC 60947-3
- IS 13947-3
- EN 60947-3
- NBN EN 60947-3
- BS EN 60947-3
The information provided in this instruction manual is subject to change without notice, remains for general
information only and is non-contractual.

ATySgM - 542933D - SOCOMEC 5EN
2. INTRODUCTION
ATyS g M “Automatic Transfer Switching Equipment” (ATSE) is designed for use in power systems for the safe transfer of
a load supply between a normal and an alternate source. The changeover is done in open transition and with minimum
supply interruption during transfer ensuring full compliance with IEC 60947-6-1, GB 14048-11 and other international TSE
standards as listed.
The ATyS g M is a full load break (switch type) derived transfer switching equipment where the main components are
proven technology devices also fullling requirements in IEC 60947-3 standards.
As a Class PC ATSE, the ATyS g M is capable of “making and withstanding short circuit currents” assigned to IEC 60947-
3 utilization categories of up to AC23A, GB 14048-11, IEC 60947-6-1 and equivalent standards with utilization categories
of up to AC33B.
ATySgM transfer switches ensure:
• Power Control and Safety between a normal and an alternate source.
• A complete product delivered as a fully assembled and tested solution.
• Intuitive HMI for emergency / local operation.
• Integrated and robust switch disconnection.
• Window with clearly visible position indication I – 0 - II.
• An inherent failsafe mechanical interlock.
• Stable positions (I – 0 – II) non affected by typical vibration and shocks.
• Constant pressure on the contacts non affected by network voltage.
• Energy Efcient with virtually no consumption whilst on the normal, alternate or off positions.
• Extremely rugged, error free and built in padlocking facility (congurable).
• Straight forward installation with effective ergonomics.
• Simple motorization control interface.
• ATS conguration thr ough 4 potentiometers and DIP switches.
• Auxiliary contacts for switch positions I – 0 - II (optional).
• “Product availability” output.
• Ample accessories to suit specic requirements.
• Fully integrated ATS controller specically designed for Mains / Mains and Mains / Genset applications.
2.1. The ATyS family product range
Just the right ATyS for your application…
ATyS: Small Footprint ATyS M: Modular Prole
Back to Back
Conguration
125A - 3200A
40A - 160A
40A - 125A
ATySp
Power / Genset
Management
ATySpM
Evolved Genset
Management
ATySg
Simple Genset
Management
ATySgM
Simple Genset
Management
ATySt
Transformer
Management
ATyStM
Transformer (building)
Management
ATySdS
Small Genset
with DPS
ATySd
RTSE (DPS)
ATySdM
RTSE (DPS)
Side by Side Conguration
ATySS (RTSE)
Small Gense
ATySr
RTSE
(1)
ATyS
RTSE
(1) The UL version of ATySr is available from 100-400A

ATySgM - 542933D - SOCOMEC
6EN
2.2. The ATyS M Range Key Features
Selecting the right ATyS M will depend on the application, the functionality required as well as the nature of the installation
in which the ATyS M will be installed. Below is an outline product selection chart listing the key features of each product to
help you select the right ATyS M for your needs.
ATyS dM ATyS tM ATyS gM ATyS pM
160 A
40 A
OPEN TRANSITION MOTORISED CHANGEOVER SWITCH
DUAL POWER SUPPLY
BUILT-IN ATS CONTROLLER
COMMUNICATION*
* Specific version. ** Return to zero without external energy source. TRIPPING**
A product for virtually all power changeover applications from 40 to 160 A
 Network / Genset
 Genset / Genset
 Network / Network
Applications with an
External ATS Control
Network / Genset

Network / Network
ATyS dM
GS
UPS
Network / Network
Building applications
ATyS p M
ATyS t M
UPS
ATyS pM
Non-critical
loads
Non-critical
loads
Critical
loads
 Network / Genset
Genset Applications for
Standby Power
UPS
ATyS gM
Non-critical
loads
Critical
loads
Critical
loads

ATySgM - 542933D - SOCOMEC 7EN
2.2.1. Selection guide
Six ratings 40 / 63 / 80 / 100 / 125 / 160 A
ATyS dM ATyS tM ATyS gM ATyS pM
APPLICATIONS
Normal / Backup without automatic controller
•
Normal / Backup with built-in automatic controller
• • •
Stable positions
• • • •
Load changeover
•
FUNCTIONS
POWER SUPPLY
External
•
Integrated
• • •
OPERATION
Backup manual operation of the 3 positions
• • • •
Electrical (dry contact) control of positions I, 0 and II
• •*
Automatic control of positions I, 0 and II
• • •
Return to 0 position feature upon loss of source
•
MONITORING
3 voltages on networks I and II
• • •
Frequency on networks I and II
• • •
Phase rotation on networks I and II
•
Asymmetry of networks I and II
•
AUTOMATIC CONTROLLER CONFIGURATION
By potentiometer and micro-switch
• •
By screen + keyboard
•
Vn, Fn, V threshold, F threshold
• • •
Driving with or without priority
• • •
Adjustable operating timers
• • •
Preset configuration
Control type (impulse or switch / contactor)
•
DISPLAY
Position, fully visualised breaking
• • • •
LED: source status, automatic mode, fault LED
• • •
LED: switch positions, supply, tests, control
•
V, F, timers, number of operations, last event
•
REMOTE CONTROL
Outputs
Generator start / stop order
• •
Product availability (not fault and not manual mode)
• •*
Source available
• •*
Programmable output (source, availability, fault)
•*
Inputs
Test on load
• •*
Retransfer
• •*
Automatic mode inhibit
• • •*
Position O order
• •*
Priority
• • •
Other programmable inputs
(test off-load, position control, etc.)
•*
Remote control
Human / Machine Interface (D10 and D20)
•
RS485 communication (MODBUS)
•**
* 3 inputs / 3 outputs (programmable).
** Product reference is different: communication by RS485 connection (MODBUS) allows up to 31 ATyS M to be connected to a PC or a PLC over 1500 m.

ATySgM - 542933D - SOCOMEC
8EN
3. QUICK START
3.1. Quick Start ATySgM (2P)
quick start 40-160A (2P)
EN
ATyS gM
Automatic
Transfer Switching Equipment
Printing informations: 1 color Black. White paper 90g/m
2
.
Printing size: 420x297. Final size 210x297. This page visible first.
A separate sheet for each language.
Non contractual document.
Subject to change without notice.
Preliminary operations
Check the following upon delivery and after removal of the
packaging:
nPackaging and contents are in good condition.
nThe product reference corresponds to the order.
nContents should include:
Qty 1 x ATyS M
Qty 1 x Emergency handle extension ROD
Qty 1 x Set of terminals
Quick Start instruction sheet
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
nThis product must always be installed and commissioned
by qualified and approved personnel.
nMaintenance and servicing operations should be
performed by trained and authorised personnel.
nDo not handle any control or power cables connected to
the product when voltage may be, or may become present
on the product, directly through the mains or indirectly
through external circuits.
nAlways use an appropriate voltage detection device to
confirm the absence of voltage.
nEnsure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Risk of damaging the device
nIn case the product is dropped or damaged in any way it
is recommended to replace the complete product.
Accessories
nBridging bars and 125A or 160A.
nControl voltage transformer (400Vac -> 230Vac).
nVoltage sensine and power supply TAP.
nTerminal shrouds.
nAdditionnal aux contact block.
nPolycarbonate enclosure.
nPolycarbonate extension box.
nPower Connection Terminals.
nSealable cover.
STEP 1
Cabinet / Back
Plate Installation
STEP 3
CONTROL /
AUX POWER
terminal
connections
STEP 2
Connecting the
POWER section
STEP 4
CHECK
STEP 5
Programming
Installation and Commissioning STEP 6A
Automatic Operation
STEP 6C
Padlocking
STEP 6B
Emergency Manual
Operation
STEP 3
CONTROL / AUX POWER Terminals and wiring
Ensure that the product is in Manual
Mode (front cover open).
Slotted head 3mm 0,5 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 1001
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 1011
2 4 6 8
135 7
2 4 6 8
1 3 5 7
207 208 209 210 63 64 73 74
6 mm /
Capacité de raccordement
0,236 "
# 20 to # 14 AWG
0,5 to 2,5 mm
0,5 to 1,5 mm2
2
# 20 to # 16 AWG
Slotted head 3 mm
3,97 lb-in 0,5 Nm
2 4 6 8
135 7
2 4 6 8
135 7
2 4 6 8
1 3 5 7
2 4 6 8
1 3 5 7
/
I1 I2 I3
O1 O2
207 208 209 210 63 64 73 74
/
I1 I2 I3
O1 O2
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
LOAD
www.socomec.com
www.socomec.com/operating-instructions
To download, brochures, catalogues and technical manuals.
STEP 1
The ATyS M is delivered with
padlocking configured to the
O position.
To allow padlocking in all
positions (I - O - II), configure
the ATySM as follows before
installation. (Screw is located
at the back of the product).
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Installation Padlocking configuration
Caution: Ensure that the product is installed on a flat rigid surface.
Recommended orientation
Recommended Ok Ok Ok Ok Ok
OK OK OK OK OK OK
OK OK OK OK OK OK
OK OK OK OK OK OK
2 clips de verrouillage
Posidriv PZ1
1 Nm
Tighten to avoid
movementonthe DINrail.
2x
2x
!
2 clips de verrouillage
DIN RAIL
IEC 60715
MAX : 2
235
26
116
53
46
73,5
245
143
350
18
45
13
222
235
131,5 131,5
47
52 176
224
MAX : 2
235
26
116
53
46
73,5
245
143
350
18
45
13
222
4 mounting brackets
6x M6 screw - 2,5 Nm
STEP 2
Power Terminal Connections
Source supply side
Hexagonal Metric
Allen size 4
5,0 Nm
It is essential to tighten all used
terminals, with cables and/or
bridging bars, before use.
Voltage taps provide 2x ≤ 1.5mm2connections.
They can be fitted in any terminals on the source
supply side. Do not use on the load side when
equipped with a bridging bar.
Load side
bridging bar.
125A: 1309 2006
160A: 1309 2016
Slotted head 3,5 mm
0,45 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
10 to
70 mm²
15mm
Type Terminal no. Status of
thecontact Description Output characteristics
Recommended
connection
cross-section
Auxiliary contact
block
1309 1001
11/12/14 11 14
12 Changeover switch in position I 250V AC 5A AC1
30 Vdc 5 A
0.5 to 2.5 mm²
(rigid)
0.5 to 1.5 mm²
(stranded)
21/22/24 21 24
22 Changeover switch in position II 250V AC 5A AC1
30 Vdc 5 A
01/02/04 01 04
02 Changeover switch in position 0 250V AC 5A AC1
30 Vdc 5 A
Auxiliary contact
block
1309 1011
11/12/14 11 14
12
21 24
22
01 04
02
Changeover switch in position I 250V AC 5A AC1
30 Vdc 5 A
21/22/24 Changeover switch in position II 250V AC 5A AC1
30 Vdc 5 A
01/02/04 Changeover switch in position 0 250V AC 5A AC1
30 Vdc 5 A
Type Terminal no. Application Status of the
contact Description Output characteristics
Recommended
connection
cross-section
Inputs I1: 207 / 208 Network/Network With priority
Dry potential free
contact
0.5 to 2.5 mm²
(rigid)
0.5 to 1.5 mm²
(stranded)
Without priority
Network-Genset. Automatic retransfer
Manual Retransfer
I1: 207 / 209 Network/Network Source priority 1
Dry potential free
contact
Source priority 2
Network-Genset. Stop the test on load
Test on load
I3: 207 / 210 Network-Network or
Network-Generating
set
AUTO mode Dry potential free
contact
Automatic mode inhibition
Outputs O1: 63 / 64 Network-Network or
Network-Generating
set
Product not available :
- Manual mode
- Command default
- Electronic default
- No source
Resistive load
2A 30 Vdc
0.5A 230Vac
Pmax : 60W or 125VA
Umax : 30Vdc or
230Vac
Product available
O2: 73 / 74 Network-Genset.
No start command genset
Resistive load
2A 30 Vdc
0.5A 230Vac
Pmax : 60W or 125VA
Umax : 30Vdc or
230Vac
Generating set starting
Pozidriv PZ2 - 1 Nm
Use 20mm
screws for
1 module
Use 35mm
screws for
2 modules
!
Auxiliary contacts: Fitting of auxiliary contacts: 1309 1001 or 1309 1011
To fit an AC, the switch must first be put in position 0. An auxiliary contact module comprises: one NO/
NC changeover contact for each position (I-0-II). To install use the long screws supplied with the module.
OKOK
OKOK
Allen size 4
Hexagonal Metric
44.1 lb-in 5,0 Nm
15 mm / 0,59 "
# 8 to # 00 AWG
10 to 70 mm2
10 to 70 mm2*
# 8 to # 00 AWG
!X4
OKOK
OKOK
Allen size 4
Hexagonal Metric
44.1 lb-in 5,0 Nm
15 mm / 0,59 "
# 8 to # 00 AWG
10 to 70 mm2
10 to 70 mm2*
# 8 to # 00 AWG
!X4
Step 1
Step 2
Step 3
CORPORATE HQ CONTACT:
SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE
542955E

ATySgM - 542933D - SOCOMEC 9EN
quick start 40-160A (2P)
EN
ATyS gM
Automatic
Transfer Switching Equipment
Printing informations: 1 color Black. White paper 90g/m
2
.
Printing size: 420x297. Final size 210x297. This page visible first.
A separate sheet for each language.
Non contractual document.
Subject to change without notice.
Preliminary operations
Check the following upon delivery and after removal of the
packaging:
nPackaging and contents are in good condition.
nThe product reference corresponds to the order.
nContents should include:
Qty 1 x ATyS M
Qty 1 x Emergency handle extension ROD
Qty 1 x Set of terminals
Quick Start instruction sheet
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
nThis product must always be installed and commissioned
by qualified and approved personnel.
nMaintenance and servicing operations should be
performed by trained and authorised personnel.
nDo not handle any control or power cables connected to
the product when voltage may be, or may become present
on the product, directly through the mains or indirectly
through external circuits.
nAlways use an appropriate voltage detection device to
confirm the absence of voltage.
nEnsure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Risk of damaging the device
nIn case the product is dropped or damaged in any way it
is recommended to replace the complete product.
Accessories
nBridging bars and 125A or 160A.
nControl voltage transformer (400Vac -> 230Vac).
nVoltage sensine and power supply TAP.
nTerminal shrouds.
nAdditionnal aux contact block.
nPolycarbonate enclosure.
nPolycarbonate extension box.
nPower Connection Terminals.
nSealable cover.
STEP 1
Cabinet / Back
Plate Installation
STEP 3
CONTROL /
AUX POWER
terminal
connections
STEP 2
Connecting the
POWER section
STEP 4
CHECK
STEP 5
Programming
Installation and Commissioning STEP 6A
Automatic Operation
STEP 6C
Padlocking
STEP 6B
Emergency Manual
Operation
STEP 3
CONTROL / AUX POWER Terminals and wiring
Ensure that the product is in Manual
Mode (front cover open).
Slotted head 3mm 0,5 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 1001
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 1011
2 4 6 8
135 7
2 4 6 8
1 3 5 7
207 208 209 210 63 64 73 74
6 mm /
Capacité de raccordement
0,236 "
# 20 to # 14 AWG
0,5 to 2,5 mm
0,5 to 1,5 mm2
2
# 20 to # 16 AWG
Slotted head 3 mm
3,97 lb-in 0,5 Nm
2 4 6 8
135 7
2 4 6 8
135 7
2 4 6 8
1 3 5 7
2 4 6 8
1 3 5 7
/
I1 I2 I3
O1 O2
207 208 209 210 63 64 73 74
/
I1 I2 I3
O1 O2
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
LOAD
www.socomec.com
www.socomec.com/operating-instructions
To download, brochures, catalogues and technical manuals.
STEP 1
The ATyS M is delivered with
padlocking configured to the
O position.
To allow padlocking in all
positions (I - O - II), configure
the ATySM as follows before
installation. (Screw is located
at the back of the product).
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Installation Padlocking configuration
Caution: Ensure that the product is installed on a flat rigid surface.
Recommended orientation
Recommended Ok Ok Ok Ok Ok
OK OK OK OK OK OK
OK OK OK OK OK OK
OK OK OK OK OK OK
2 clips de verrouillage
Posidriv PZ1
1 Nm
Tighten to avoid
movementonthe DINrail.
2x
2x
!
2 clips de verrouillage
DIN RAIL
IEC 60715
MAX : 2
235
26
116
53
46
73,5
245
143
350
18
45
13
222
235
131,5 131,5
47
52 176
224
MAX : 2
235
26
116
53
46
73,5
245
143
350
18
45
13
222
4 mounting brackets
6x M6 screw - 2,5 Nm
STEP 2
Power Terminal Connections
Source supply side
Hexagonal Metric
Allen size 4
5,0 Nm
It is essential to tighten all used
terminals, with cables and/or
bridging bars, before use.
Voltage taps provide 2x ≤ 1.5mm2connections.
They can be fitted in any terminals on the source
supply side. Do not use on the load side when
equipped with a bridging bar.
Load side
bridging bar.
125A: 1309 2006
160A: 1309 2016
Slotted head 3,5 mm
0,45 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
10 to
70 mm²
15mm
Type Terminal no. Status of
thecontact Description Output characteristics
Recommended
connection
cross-section
Auxiliary contact
block
1309 1001
11/12/14 11 14
12 Changeover switch in position I 250V AC 5A AC1
30 Vdc 5 A
0.5 to 2.5 mm²
(rigid)
0.5 to 1.5 mm²
(stranded)
21/22/24 21 24
22 Changeover switch in position II 250V AC 5A AC1
30 Vdc 5 A
01/02/04 01 04
02 Changeover switch in position 0 250V AC 5A AC1
30 Vdc 5 A
Auxiliary contact
block
1309 1011
11/12/14 11 14
12
21 24
22
01 04
02
Changeover switch in position I 250V AC 5A AC1
30 Vdc 5 A
21/22/24 Changeover switch in position II 250V AC 5A AC1
30 Vdc 5 A
01/02/04 Changeover switch in position 0 250V AC 5A AC1
30 Vdc 5 A
Type Terminal no. Application Status of the
contact Description Output characteristics
Recommended
connection
cross-section
Inputs I1: 207 / 208 Network/Network With priority
Dry potential free
contact
0.5 to 2.5 mm²
(rigid)
0.5 to 1.5 mm²
(stranded)
Without priority
Network-Genset. Automatic retransfer
Manual Retransfer
I1: 207 / 209 Network/Network Source priority 1
Dry potential free
contact
Source priority 2
Network-Genset. Stop the test on load
Test on load
I3: 207 / 210 Network-Network or
Network-Generating
set
AUTO mode Dry potential free
contact
Automatic mode inhibition
Outputs O1: 63 / 64 Network-Network or
Network-Generating
set
Product not available :
- Manual mode
- Command default
- Electronic default
- No source
Resistive load
2A 30 Vdc
0.5A 230Vac
Pmax : 60W or 125VA
Umax : 30Vdc or
230Vac
Product available
O2: 73 / 74 Network-Genset.
No start command genset
Resistive load
2A 30 Vdc
0.5A 230Vac
Pmax : 60W or 125VA
Umax : 30Vdc or
230Vac
Generating set starting
Pozidriv PZ2 - 1 Nm
Use 20mm
screws for
1 module
Use 35mm
screws for
2 modules
!
Auxiliary contacts: Fitting of auxiliary contacts: 1309 1001 or 1309 1011
To fit an AC, the switch must first be put in position 0. An auxiliary contact module comprises: one NO/
NC changeover contact for each position (I-0-II). To install use the long screws supplied with the module.
OKOK
OKOK
Allen size 4
Hexagonal Metric
44.1 lb-in 5,0 Nm
15 mm / 0,59 "
# 8 to # 00 AWG
10 to 70 mm2
10 to 70 mm2*
# 8 to # 00 AWG
!X4
OKOK
OKOK
Allen size 4
Hexagonal Metric
44.1 lb-in 5,0 Nm
15 mm / 0,59 "
# 8 to # 00 AWG
10 to 70 mm2
10 to 70 mm2*
# 8 to # 00 AWG
!X4
Step 1
Step 2
Step 3
CORPORATE HQ CONTACT:
SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE
542955E

ATySgM - 542933D - SOCOMEC
10 EN
STEP 5
Programming
Check
STEP 6A
Automatic operation
Close the front cover as shown to put the
product into automatic mode.
STEP 4
Whilst in manual mode, check the
wiring and if ok power up the
product.
STEP 6B
Manual operation
• Open the front cover as shown to put
into manual mode.
•
Use the handle situated in the front
panel under the cover to operate the
transfer switch.
•
Check the changeover switch position
on the indicator before operating.
To simplify operation
use the handle with the
extension provided. (Max 8 Nm)
II
I
o
0,5 to 2,5 mm2
#28 to #14 AWG
0,5 to 2,5 mm2
#28 to #14 AWG
6 mm / 0,236"
Slotted head 2,5 mm
90º 90º
Extension
The LED signalling and operation is only active when the product supply is available.
To set the dip switches, it is necessary to open the Auto/Manual cover.
Commissioning must always result in having at least 1 LED source available on.
(Therefore, the voltage and frequency must be within the defined thresholds).
Any action on the potentiometers will change the settings, even when the cover is closed.
Source LED ON LED OFF LED blinking
Source 1 available Source 1 not available
or out of range
- a timer is counting down
- test mode
Source 2 available Source 2 not available
or out of range
- a timer is counting down
Source availability LED
• E: No stop in O position
• F: 2s stop in O position
Stop in 0 position: E-F
• G: Network - Genset
• H: Network - Network
Type of application: G-H
Dip switch settings
LED info
Source supply voltage
andfrequency
Auto-Configuration
A
E
Hysteresis settings
B
Loss of priority source timer
FT: 0-60 sec.
FT
RT
U/F [HYST]
[HYST]
RT: 0-30 min.
U/F
Timer settings
C D
Fault reset
Return of priority sourcetimer
LED ON LED OFF LED blinking
Fault Product OK or
S1-S2not available
Please wait
Auto mode Manual mode Manual retransfer
Fault and state of the product LED's
STEP 6C
Padlocking mode
• In order to padlock put the product in
manual mode.
•
Pull the locking mechanism and insert
a padlock as shown.
• As standard padlocking in the 0 position.
Configurable to I-0-II (see step 1).
1x 4-8 mm
LED state Auto Conf result Action
Steady ON OK Ready
Blinking Not OK Go back to step 4
Ensure that the supply
voltage is available and
within the following limits:
Un: 176-288VAC
Fn: 45-65Hz
Press PROG for ≥ 2s
HYST: 20 %DU/F
DU: 5-20%
DF: 3-10%

ATySgM - 542933D - SOCOMEC 11EN

ATySgM - 542933D - SOCOMEC
12 EN
quick start 40-160A (4P)
EN
ATyS gM
Automatic
Transfer Switching Equipment
Preliminary operations
Check the following upon delivery and after removal of the
packaging:
nPackaging and contents are in good condition.
nThe product reference corresponds to the order.
nContents should include:
Qty 1 x ATyS M
Qty 1 x Emergency handle extension ROD
Qty 1 x Set of terminals
Quick Start instruction sheet
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
nThis product must always be installed and commissioned
by qualified and approved personnel.
nMaintenance and servicing operations should be
performed by trained and authorised personnel.
nDo not handle any control or power cables connected to
the product when voltage may be, or may become present
on the product, directly through the mains or indirectly
through external circuits.
nAlways use an appropriate voltage detection device to
confirm the absence of voltage.
nEnsure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Risk of damaging the device
nIn case the product is dropped or damaged in any way it
is recommended to replace the complete product.
Accessories
nBridging bars and 125A or 160A.
nControl voltage transformer (400Vac -> 230Vac).
nVoltage sensine and power supply TAP.
nTerminal shrouds.
nAdditionnal aux contact block.
nPolycarbonate enclosure.
nPolycarbonate extension box.
nPower Connection Terminals.
nSealable cover.
Printing informations: 1 color Black. White paper 90g/m
2
.
Printing size: 420x297. Final size 210x297. This page visible first.
A separate sheet for each language.
Non contractual document.
Subject to change without notice.
STEP 1
Cabinet / Back
Plate Installation
STEP 3
CONTROL /
AUX POWER
terminal
connections
STEP 2
Connecting the
POWER section
STEP 4
CHECK
STEP 5
Programming
Installation and Commissioning STEP 6A
Automatic Operation
STEP 6C
Padlocking
STEP 6B
Emergency Manual
Operation
STEP 3
CONTROL / AUX POWER Terminals and wiring
Type Terminal no. Status of
thecontact Description Output characteristics
Recommended
connection
cross-section
Auxiliary contact
block
1309 1001
11/12/14 11 14
12 Changeover switch in position I 250V AC 5A AC1
30 Vdc 5 A
0.5 to 2.5 mm²
(rigid)
0.5 to 1.5 mm²
(stranded)
21/22/24 21 24
22 Changeover switch in position II 250V AC 5A AC1
30 Vdc 5 A
01/02/04 01 04
02 Changeover switch in position 0 250V AC 5A AC1
30 Vdc 5 A
Auxiliary contact
block
1309 1011
11/12/14 11 14
12
21 24
22
01 04
02
Changeover switch in position I 250V AC 5A AC1
30 Vdc 5 A
21/22/24 Changeover switch in position II 250V AC 5A AC1
30 Vdc 5 A
01/02/04 Changeover switch in position 0 250V AC 5A AC1
30 Vdc 5 A
2 4 6 8
135 7
2 4 6 8
1 3 5 7
207 208 209 210 63 64 73 74
6 mm /
Capacité de raccordement
0,236 "
# 20 to # 14 AWG
0,5 to 2,5 mm
0,5 to 1,5 mm2
2
# 20 to # 16 AWG
Slotted head 3 mm
3,97 lb-in 0,5 Nm
2 4 6 8
135 7
2 4 6 8
135 7
2 4 6 8
1 3 5 7
2 4 6 8
1 3 5 7
/
I1 I2 I3
O1 O2
207 208 209 210 63 64 73 74
/
I1 I2 I3
O1 O2
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
LOAD
Type Terminal no. Application Status of the
contact Description Output characteristics
Recommended
connection
cross-section
Inputs I1: 207 / 208 Network/Network With priority
Dry potential free
contact
0.5 to 2.5 mm²
(rigid)
0.5 to 1.5 mm²
(stranded)
Without priority
Network-Genset. Automatic retransfer
Manual Retransfer
I1: 207 / 209 Network/Network Source priority 1
Dry potential free
contact
Source priority 2
Network-Genset. Stop the test on load
Test on load
I3: 207 / 210 Network-Network or
Network-Generating
set
AUTO mode
Dry potential free
contact
Automatic mode inhibition
Outputs O1: 63 / 64 Network-Network or
Network-Generating
set
Product not available :
- Manual mode
- Command default
- Electronic default
- No source
Resistive load
2A 30 Vdc
0.5A 230Vac
Pmax : 60W or 125VA
Umax : 30Vdc or
230Vac
Product available
O2: 73 / 74 Network-Genset.
No start command genset Resistive load
2A 30 Vdc
0.5A 230Vac
Pmax : 60W or 125VA
Umax : 30Vdc or
230Vac
Generating set starting
Ensure that the product is in
Manual Mode (front cover
open).
230/127V~
3ph 4wires
230/127V~
3ph 3wires
Slotted head 3mm 0,5 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 1001
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 1011
Pozidriv PZ2 - 1 Nm
Use 20mm
screws for
1 module
Use 35mm
screws for
2 modules
!
Auxiliary contacts: Fitting of auxiliary contacts: 1309 1001 or 1309 1011
To fit an AC, the switch must first be put in position 0. An auxiliary contact module comprises: one NO/
NC changeover contact for each position (I-0-II). To install use the long screws supplied with the module.
www.socomec.com
www.socomec.com/operating-instructions
To download, brochures, catalogues and technical manuals.
STEP 1
The ATyS M is delivered with
padlocking configured to the
O position.
To allow padlocking in all
positions (I - O - II), configure
the ATySM as follows before
installation. (Screw is located
at the back of the product).
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Installation Padlocking configuration
Caution: Ensure that the product is installed on a flat rigid surface.
MAX : 2
340
26
116
53
46
73,5
245
143 350
18
45
13
324
340
326
131,5
131,5
52 104 176
47
Recommended orientation
Recommended Ok Ok Ok Ok Ok
OK OK OK OK OK OK
OK OK OK OK OK OK
OK OK OK OK OK OK
2 clips de verrouillage
Posidriv PZ1
1 Nm
Tighten to avoid
movementonthe DINrail.
DIN RAIL
IEC 60715
6 mounting brackets
6x M6 screw - 2,5 Nm
2x
2x
STEP 2
Power Terminal Connections
Source supply side
Hexagonal Metric
Allen size 4
5,0 Nm
It is essential to tighten all used
terminals, with cables and/or
bridging bars, before use.
Allen size 4
Hexagonal Metric
44,1 lb-in 5,0 Nm
15 mm / 0,59 "
# 8 to # 00 AWG
10 to 70 mm2
6 to 70 mm2*
# 10 to # 00 AWG
!
X8
Allen size 4
Hexagonal Metric
44,1 lb-in 5,0 Nm
15 mm / 0,59 "
# 8 to # 00 AWG
10 to 70 mm2
6 to 70 mm2*
# 10 to # 00 AWG
!
X8
Voltage taps provide 2x ≤ 1.5mm2connections.
They can be fitted in any terminals on the source
supply side. Do not use on the load side when
equipped with a bridging bar.
Load side
bridging bar.
125A: 1309 4006
160A: 1309 4016
Slotted head 3,5 mm
0,45 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
10 to
70 mm²
15mm
MAX : 2
340
26
116
53
46
73,5
245
143
350
18
45
13
324
!
Step 1
Step 2
Step 3
CORPORATE HQ CONTACT:
SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE
542932E
3.2. Quick Start ATySgM (4P)

ATySgM - 542933D - SOCOMEC 13EN
quick start 40-160A (4P)
EN
ATyS gM
Automatic
Transfer Switching Equipment
Preliminary operations
Check the following upon delivery and after removal of the
packaging:
nPackaging and contents are in good condition.
nThe product reference corresponds to the order.
nContents should include:
Qty 1 x ATyS M
Qty 1 x Emergency handle extension ROD
Qty 1 x Set of terminals
Quick Start instruction sheet
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
nThis product must always be installed and commissioned
by qualified and approved personnel.
nMaintenance and servicing operations should be
performed by trained and authorised personnel.
nDo not handle any control or power cables connected to
the product when voltage may be, or may become present
on the product, directly through the mains or indirectly
through external circuits.
nAlways use an appropriate voltage detection device to
confirm the absence of voltage.
nEnsure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Risk of damaging the device
nIn case the product is dropped or damaged in any way it
is recommended to replace the complete product.
Accessories
nBridging bars and 125A or 160A.
nControl voltage transformer (400Vac -> 230Vac).
nVoltage sensine and power supply TAP.
nTerminal shrouds.
nAdditionnal aux contact block.
nPolycarbonate enclosure.
nPolycarbonate extension box.
nPower Connection Terminals.
nSealable cover.
Printing informations: 1 color Black. White paper 90g/m
2
.
Printing size: 420x297. Final size 210x297. This page visible first.
A separate sheet for each language.
Non contractual document.
Subject to change without notice.
STEP 1
Cabinet / Back
Plate Installation
STEP 3
CONTROL /
AUX POWER
terminal
connections
STEP 2
Connecting the
POWER section
STEP 4
CHECK
STEP 5
Programming
Installation and Commissioning STEP 6A
Automatic Operation
STEP 6C
Padlocking
STEP 6B
Emergency Manual
Operation
STEP 3
CONTROL / AUX POWER Terminals and wiring
Type Terminal no. Status of
thecontact Description Output characteristics
Recommended
connection
cross-section
Auxiliary contact
block
1309 1001
11/12/14 11 14
12 Changeover switch in position I 250V AC 5A AC1
30 Vdc 5 A
0.5 to 2.5 mm²
(rigid)
0.5 to 1.5 mm²
(stranded)
21/22/24 21 24
22 Changeover switch in position II 250V AC 5A AC1
30 Vdc 5 A
01/02/04 01 04
02 Changeover switch in position 0 250V AC 5A AC1
30 Vdc 5 A
Auxiliary contact
block
1309 1011
11/12/14 11 14
12
21 24
22
01 04
02
Changeover switch in position I 250V AC 5A AC1
30 Vdc 5 A
21/22/24 Changeover switch in position II 250V AC 5A AC1
30 Vdc 5 A
01/02/04 Changeover switch in position 0 250V AC 5A AC1
30 Vdc 5 A
2 4 6 8
135 7
2 4 6 8
1 3 5 7
207 208 209 210 63 64 73 74
6 mm /
Capacité de raccordement
0,236 "
# 20 to # 14 AWG
0,5 to 2,5 mm
0,5 to 1,5 mm2
2
# 20 to # 16 AWG
Slotted head 3 mm
3,97 lb-in 0,5 Nm
2 4 6 8
135 7
2 4 6 8
135 7
2 4 6 8
1 3 5 7
2 4 6 8
1 3 5 7
/
I1 I2 I3
O1 O2
207 208 209 210 63 64 73 74
/
I1 I2 I3
O1 O2
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
LOAD
Type Terminal no. Application Status of the
contact Description Output characteristics
Recommended
connection
cross-section
Inputs I1: 207 / 208 Network/Network With priority
Dry potential free
contact
0.5 to 2.5 mm²
(rigid)
0.5 to 1.5 mm²
(stranded)
Without priority
Network-Genset. Automatic retransfer
Manual Retransfer
I1: 207 / 209 Network/Network Source priority 1
Dry potential free
contact
Source priority 2
Network-Genset. Stop the test on load
Test on load
I3: 207 / 210 Network-Network or
Network-Generating
set
AUTO mode
Dry potential free
contact
Automatic mode inhibition
Outputs O1: 63 / 64 Network-Network or
Network-Generating
set
Product not available :
- Manual mode
- Command default
- Electronic default
- No source
Resistive load
2A 30 Vdc
0.5A 230Vac
Pmax : 60W or 125VA
Umax : 30Vdc or
230Vac
Product available
O2: 73 / 74 Network-Genset.
No start command genset Resistive load
2A 30 Vdc
0.5A 230Vac
Pmax : 60W or 125VA
Umax : 30Vdc or
230Vac
Generating set starting
Ensure that the product is in
Manual Mode (front cover
open).
230/127V~
3ph 4wires
230/127V~
3ph 3wires
Slotted head 3mm 0,5 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 1001
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 1011
Pozidriv PZ2 - 1 Nm
Use 20mm
screws for
1 module
Use 35mm
screws for
2 modules
!
Auxiliary contacts: Fitting of auxiliary contacts: 1309 1001 or 1309 1011
To fit an AC, the switch must first be put in position 0. An auxiliary contact module comprises: one NO/
NC changeover contact for each position (I-0-II). To install use the long screws supplied with the module.
www.socomec.com
www.socomec.com/operating-instructions
To download, brochures, catalogues and technical manuals.
STEP 1
The ATyS M is delivered with
padlocking configured to the
O position.
To allow padlocking in all
positions (I - O - II), configure
the ATySM as follows before
installation. (Screw is located
at the back of the product).
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Posidriv PZ2
OK
OK !
!
STEP 1
STEP 2
STEP 3
STEP 4
Posidriv PZ2
Posidriv PZ2
2,2 lb-in 0,25 Nm
2 X
Installation Padlocking configuration
Caution: Ensure that the product is installed on a flat rigid surface.
MAX : 2
340
26
116
53
46
73,5
245
143 350
18
45
13
324
340
326
131,5
131,5
52 104 176
47
Recommended orientation
Recommended Ok Ok Ok Ok Ok
OK OK OK OK OK OK
OK OK OK OK OK OK
OK OK OK OK OK OK
2 clips de verrouillage
Posidriv PZ1
1 Nm
Tighten to avoid
movementonthe DINrail.
DIN RAIL
IEC 60715
6 mounting brackets
6x M6 screw - 2,5 Nm
2x
2x
STEP 2
Power Terminal Connections
Source supply side
Hexagonal Metric
Allen size 4
5,0 Nm
It is essential to tighten all used
terminals, with cables and/or
bridging bars, before use.
Allen size 4
Hexagonal Metric
44,1 lb-in 5,0 Nm
15 mm / 0,59 "
# 8 to # 00 AWG
10 to 70 mm2
6 to 70 mm2*
# 10 to # 00 AWG
!
X8
Allen size 4
Hexagonal Metric
44,1 lb-in 5,0 Nm
15 mm / 0,59 "
# 8 to # 00 AWG
10 to 70 mm2
6 to 70 mm2*
# 10 to # 00 AWG
!
X8
Voltage taps provide 2x ≤ 1.5mm2connections.
They can be fitted in any terminals on the source
supply side. Do not use on the load side when
equipped with a bridging bar.
Load side
bridging bar.
125A: 1309 4006
160A: 1309 4016
Slotted head 3,5 mm
0,45 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
10 to
70 mm²
15mm
MAX : 2
340
26
116
53
46
73,5
245
143
350
18
45
13
324
!
Step 1
Step 2
Step 3
CORPORATE HQ CONTACT:
SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE
542932E

ATySgM - 542933D - SOCOMEC
14 EN
FT
STEP 5
Programming
Check
STEP 6A
Automatic operation
Close the front cover as shown to put the
product into automatic mode.
STEP 4
Whilst in manual mode, check the
wiring and if ok power up the
product.
STEP 6C
Padlocking mode
• In order to padlock put the product in
manual mode.
•
Pull the locking mechanism and insert
a padlock as shown.
• As standard padlocking in the 0 position.
Configurable to I-0-II (see step 1).
STEP 6B
Manual operation
• Open the front cover as shown to put
into manual mode.
•
Use the handle situated in the front
panel under the cover to operate the
transfer switch.
•
Check the changeover switch position
on the indicator before operating.
To simplify operation
use the handle with the
extension provided. (Max 8 Nm)
II
I
o
0,5 to 2,5 mm2
#28 to #14 AWG
0,5 to 2,5 mm2
#28 to #14 AWG
6 mm / 0,236"
Slotted head 2,5 mm
90º 90º
Extension
1x 4-8 mm
The LED signalling and operation is only active when the product supply is available.
To set the dip switches, it is necessary to open the Auto/Manual cover.
Commissioning must always result in having at least 1 LED source available on.
(Therefore, the voltage and frequency must be within the defined thresholds).
Any action on the potentiometers will change the settings, even when the cover is closed.
Source LED ON LED OFF LED blinking
Source 1
available
Source 1
missing or
out of
range
- a timer is
counting
down
- test mode
Source 2
available
Source 2
missing or
out of
range
- a timer is
counting
down
Source availability LED
• E: No stop in O position
• F: 2s stop in O position
Stop in 0 position: E-F
• C: 50 Hz
• D: 60 Hz
Frequency: C-D
• A: 3P
• B: 1P
Type of network: A-B
• G: Network - Genset
• H: Network - Network
Type of application: G-H
HYST: 20 %DU/F
DU: 5-20%
DF: 3-10%
Dip switch settings Led info
A
Source voltage
supply configuration
B
Loss of priority source timer
127/230 Vac version 230/400 Vac version
Un (P-P):
208-240 Vac
Un (P-N):
120-138 Vac
Un (P-P):
380-420 Vac
Un (P-N):
220-240 Vac
FT: 0-30 sec.
U/F [HYST]
[HYST]
RT: 0-30 min.
U/F
Timer settings
C D
Fault reset
Return of priority sourcetimer
LED ON LED OFF LED blinking
Fault Product OK Wait
Auto mode Manual
mode
Manual
retransfer
Fault and state of the product Leds
RT

ATySgM - 542933D - SOCOMEC 15EN

ATySgM - 542933D - SOCOMEC
16 EN
4. ATYSGM VERSIONS
The ATySgM is available as 2P or 4P with the possibility of being used on virtually any automatic open transition type of
application.
Measurement accuracy: Frequency: 1% - Voltage: 1%
4.1. Product presentation
This quick-acting transfer switch incorporates:
1. 2 mechanically interlocked switches.
2. A quick-acting electric control unit enabling electric or
manual system operation.
3. Electrical specications compliant with product
standards, and a version identication.
4. Changeover switch wiring identication.
5. Control connections.
3
12
4
5
3
12
4
5
CAUTION ! Ensure that the load is
connected to the top of the switch with
the motorisation on the right hand side as
shown.
4.2. Specications and advantages
1 - Power section:
A fully integrated and interlocked transfer switch, with high electrical performance offering microprocessor control and
monitoring.
2 - Operation:
A exible operating mechanism enabling quick motorised transfer in automatic mode or locally in manual mode
for emergency operations. Features a locking device to ensure (in position zero) a secured isolation of the load
(padlocked).
4.3. Supply types
The power supply of ATySgM is required to be 220 VAC -20% to 240VAC +20% at a frequency of 50/60 Hz and has
been developed so as to meet most network congurations.
Product’s working ranges:
230 / 400 VAC Version 127 / 230 VAC Version 230 VAC Version
Umin Umax Umin Umax Umin Umax
Ph-N 176 288 176 288 176 288
Ph-Ph 305 498 305 498 / /

ATySgM - 542933D - SOCOMEC 17EN
5. OPTIONAL ACCESSORIES
Auxiliary contacts Each product can take up to 2 auxiliary contact
blocks. Each accessory integrates 1 NOC auxiliary
contact (for each position I, O and II) 13091001 or
NONC for 13091011.
Characteristics: 250 VAC / 5 A maximum. The ATyS
d M includes 1x aux contact reference 1309 1001 as
standard.
Ref. : 1309 1001
Ref. : 1309 1011
Bridging bars To provide a common point on the outgoing side of
the switch (load side).
Single phase product:
Rating ≤125A : 1309
2006 Rating 160A:
1309 2016
Three phase product:
Rating ≤125A : 1309
4006 Rating 160A:
1309 4016
Terminal shrouds Protection against direct contact with terminals
or connecting parts. Other features: Perforations
allowing remote thermographic inspection without
removal. Possibility of sealing.
Ref. : 2294 4016
2 parts/ref.
Enclosure Fully dedicated to ATySM use, this
polycarbonate enclosure provides easy access
to a compact, enclosed transfer switch (HxWxD:
385x385x193mm).
Ref. : 1309 9006
Extension unit Combined with the polycarbonate enclosure, the
extension box creates extra space for routing cables
with a larger diameter.
Ref. : 1309 9007
Single phase
residential enclosure
Dedicated to the implementation of a single-phase
ATyS M, it enables easy access to a compact power
supply switching solution.
40-160A (HxWxD: 410x305x150mm).
IP41
Ref. : 1309 9056
Sealable cover. It prevents access to the configuration panel of the
ATySgM.
Three phases product:
Ref. : 1359 0000
Single phase product:
Ref. : 1359 2000
Auto-transformer For use with ATyS M in 400 VAC three-phase
applications without a distributed neutral. As the
ATyS M has a 230Vac auxilliary power supply
requirement. When no neutral connection is available
this autotransformer (400/230 VAC, 400 VA)
provides the 230 VAC required for the ATyS M to
function.
Ref. : 1599 4121
Power connection
terminals
The power connection terminals allow conversion
of the cage terminals into bolt-on type connection
terminals, enabling connection of up to two 35mm²
cables or one 70mm² cable. Each power connection
terminal is provided with separation screens.
Ref. : 1399 4017
For complete
conversion, order 3
times the reference.

ATySgM - 542933D - SOCOMEC
18 EN
6. TECHNICAL DATA
RATINGS 40A 63 A 80 A 100 A 125 A 160 A
Frequencies 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz
Thermal current Ith at 40°C (A) 40 63 80 100 125 160
Thermal current Ith at 50°C (A) 40 63 80 100 110* 125
Thermal current Ith at 60°C (A) 40 50 63 80 100* 125
Thermal current Ith at 70°C (A) 40 40 50 63 80* 100
Rated assigned insulation voltage Ui (V) (Power circuit) 800 800 800 800 800 800
Rated impulse withstand voltage Uimp (kV) (power circuit) 666666
Rated insulation voltage Ui (V) (control circuit) 300 300 300 300 300 300
Rated impulse withstand voltage Uimp (kV) (control circuit) 2.5 2.5 2.5 2.5 2.5 2.5
Rated operational currents
(A)
IEC 60947-3 at 415 VAC at
40°C
AC 21A / 21 B 40/40 63/63 80/80 100/100 125/125 160/160
AC 22A / 22 B 40/40 63/63 80/80 100/100 125/125 125/160
AC 23A / 23 B 40/40 63/63 80/80 100/100 125/125 125/160
Rated operational currents
(A) IEC 60947-6-1 415Vac
at 40°C
AC 33B / AC32B
**AC 33iB 40/40 63/63 80/80 100/100 125/125 125**/160
Fuse protected short-circuit
withstand if using gG DIN
fuses
Fuse protected short-circuit
withstand (kA eff) 50 50 50 50 50 40
Associated fuses (gG DIN) 40 63 80 100 125 160
Short-circuit capacity
Rated short-term withstand
current: Icw 1s (kA eff) 444444
Rated short-term withstand
current: Icw 30ms (kA eff) 10 10 10 10 10 10
Switching time at In
excluding loss of supply
sensing time and excluding
any delay timers applicable.
I-II or II-I (ms) 180 180 180 180 180 180
Duration of “electrical
blackout” at Un (ms) 90 90 90 90 90 90
I-O / O-I / II-O / O-II (ms) 45 45 45 45 45 45
Consumption
Inrush current(A) 20 20 20 20 20 20
Consumption in stabilised
state (VA) 666666
Mechanical characteristics Number of changeovers 10000 10000 10000 10000 10000 10000
Connection cross-section
( not compatible with
aluminium cables)
Minimum size (Cu mm²),
flexible and rigid 10 10 10 10 10 10
Maximum size (Cu mm²),
flexible and rigid 70 70 70 70 70 70
Equipment class (According to IEC 60947-6-1) PC PC PC PC PC PC
EMC environment AAAAAA
* Possibility of reaching 125A with bigger connection cross-sections and use of the 160A bridging bar.
** AC 33iB 160A according to GB 14048.11.
This is a class A product. In a domestic environment, this product may cause radio interference in which
case the user may be required to take adequate measures.

ATySgM - 542933D - SOCOMEC 19EN
7. ENVIRONMENTAL CONDITIONS
Humidity
• 80 % humidity without condensation at 55°C
• 95 % humidity without condensation at 40°C
Temperature
• -20 +40°C without de-rating
• 40 °C < t ≤ 70 °C with de-rating (see Technical Characteristics)
Altitude
• Up to 2000m
Correction factors:
2 000 m < A ≤ 3 000m 3 000 m < A ≤ 4 000m
UE 0.95 0.80
Ie 0.85 0.85
Storage
• 1 year maximum
• Maximum storage temperature: +55 °C
• 80 % humidity without condensation at 55°C
ø 1 mm
IP rating
• IP41 in the SOCOMEC polycarbonate modular enclosure see page page 25
• IP2x for non-enclosed modular product
Protection class: Class 1

ATySgM - 542933D - SOCOMEC
20 EN
8. PRODUCT INSTALLATION
Prior to installation of the product ensure that the padlocking setting screw (located at the back of the
product) is congured as per your requirements.
For locking in Positions I, II and 0, refer to the following procedure.
8.1. Changing the padlocking conguration
To congure the locking in the 3 positions:
STEP1: loosen the screw at the back of the product as shown below.
STEP2: slide the screw upwards.
STEP3: tighten the screw in the top position as shown.
2
2x
3
Posidriv PZ2
2,2 lb-in
0,25 Nm
Posidriv PZ2
2x
1
Posidriv PZ2
2x
8.2. Recommanded orientation
OK OK OK OK OK OK
OK OK OK OK OK OK
OK OK OK OK OK OK
OK OK OK OK OK OK
OK OK OK OK OK OK
OK OK OK OK OK OK
Recommended Ok Ok Ok Ok Ok
8.3. Dimensions of the single phase 8.4. Back plate mounted single phase
MAX : 2
235
26
116
53
46
73,5
245
143
350
18
45
13
222
MAX : 2
235
26
116
53
46
73,5
245
143
350
18
45
13
222
235
131,5 131,5
47
52 176
224
4 mounting brackets
6x M6 screw - 2,5 Nm