socomec Green Power 2.0 10 User manual

Green Power 2.0
10-40 kVA
安装及操作手册 CN
Installations- und bedienungsanleitung DE
Manual de instalación y uso ES
Manuel d’installation et d’utilisation FR
Installation and operating manual GB
Manuale di installazione e uso IT
Installatie– en bedieningshandleiding NL
Dokumentacja Techniczno-Ruchowa PL
Manual de instalação e funcionamento PT
Manual de instalare şi utilizare RO
Руководство по установке и эксплуатации RU
Navodila za priključitev in uporabo SI
Kurulum ve kullanım kılavuzu TR

2Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
This SOCOMEC continuous power system is guaranteed against any manufacturing or material defects.
The warranty is valid for 12 (twelve) months from the commission date, provided activation is carried out by SOCOMEC person-
nel or personnel from a support centre authorised by SOCOMEC, and no more than 15 (fifteen) months from being shipped from
SOCOMEC.
The warranty is valid throughout national territory. If the UPS is exported abroad, the warranty will only cover the parts used to repair
faults.
The warranty is valid ex-works and covers labour and parts used to repair the faults.
The warranty shall not apply in the following cases:
• Failure due to unforeseen circumstances or force majeure (lightning, floods, etc.);
• Failure due to negligence or improper use (use outside limits: temperature, humidity, ventilation, electric power supply, applied
load, batteries);
• Insufficient or inappropriate maintenance;
• When maintenance, repairs or modifications have not carried been out by SOCOMEC personnel, or personnel from a support
centre authorised by SOCOMEC.
• If the battery has not been recharged in accordance with the terms indicated on the packaging and in the manual, in the event of
long periods of storage or UPS inactivity.
SOCOMEC may, at its own discretion, opt for the repair of the product or the replacement of faulty or defective parts with new parts,
or with used parts of equivalent quality to new parts with regard to function and performance.
Defective or faulty parts replaced free of charge must to be made available to SOCOMEC, which becomes the sole owner.
Replacement or repair of parts, or any modifications to the product during the warranty period, will not extend the duration of the
warranty.
SOCOMEC will not be responsible for damages under any circumstances (including, without limitations, damage for loss of earnings,
interruption of activity, loss of information or other financial losses) arising from the use of the product.
These conditions are subject to Italian law. Any disputes fall under the jurisdiction of the Court of Vicenza.
CERTIFICATE AND CONDITIONS OF WARRANTY
SOCOMEC retains the full and exclusive ownership rights to this document. Only a personal entitlement to use the document for the
application indicated by SOCOMEC is granted to the recipient of this document. The reproduction, modification, distribution of this
document, either partially or wholly and in any manner, is strictly prohibited except upon Socomec’s express prior written consent.
This document is not a specification. SOCOMEC reserves the right to make any changes to the information provided without prior
notice.

3
ENGLISH
Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
SUMMARY
ENGLISH
1. SAFETY STANDARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. IMPORTANT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2. DESCRIPTION OF SYMBOLS USED ON LABELS ATTACHED TO THE UNIT . . . . . . . . . 5
2. UNPACKING AND INSTALLATION OF THE UNIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1. SHIPPING AND MOVING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2. UNPACKING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3. ENVIRONMENTAL REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4. ELECTRICAL REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.5. INSTALLATION PROCEDURES AND INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.6. GENERATOR CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.7. EXTERNAL ESD CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.8. ISOLATION TRANSFORMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9. UPS PARALLEL CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.10. SPECIAL PARALLEL CONFIGURATION FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.11. EXTERNAL BATTERY CABINET CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3. MODES OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1. ON LINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2. OPERATION IN HIGH EFFICIENCY MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3. OPERATION WITH MANUAL MAINTENANCE BYPASS . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.4. OPERATION WITH EXTERNAL MANUAL BYPASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.5. OPERATION IN GE CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.6. ENERGY SAVER MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4. ACCESS TO CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.1. IDENTIFYING THE SWITCHES AND INTERFACES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.2. FUNCTIONS OF SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5. HUMAN MACHINE INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.2. MIMIC PANEL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.3. MENU NAVIGATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6. OPERATING PROCEDURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.1. SWITCHING ON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.2. COMMISSIONING WIZARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.3. SHUTDOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.4. SWITCHING ONTO MAINTENANCE BYPASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.5. SWITCHING ON FROM MAINTENANCE BYPASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.6. EXTENDED OUT OF SERVICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.7. EMERGENCY SHUTDOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.8. UPS GENERAL POWER OFF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7. CONNECTIVITY AND COMMUNICATION OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.1. MULTILEVEL COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.2. STANDARD WEB PAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.3. ADC CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
7.4. ADC CARD WITH TEMPERATURE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7.5. ISOLATED SERIAL PORT RS232 (DB9 CONNECTION) AND RS485 CARD . . . . . . . . . 43
7.6. REMOTE MIMIC PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7.7. GSM MODEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7.8. NET VISION LAN/WEB INTERFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7.9. SOFTWARE OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
7.10. SMS NOTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8. ELECTRICAL OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.1. INSULATION CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.2. REMOTE MIMIC PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.3. EXTERNAL MAINTENANCE BYPASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.4. EXTERNAL MAINTENANCE BYPASS WITH BACKFEED PROTECTION . . . . . . . . . . . . 45
8.5. ACS PCB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.6. EXTERNAL BACKFEED PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.7. PROTECTION ON MAINS SUPPLY AND AUXILIARY MAINS SUPPLY . . . . . . . . . . . . . . 46
8.8. PROTECTION ON A UPS WITHOUT AUXILARY MAINS SUPPLY . . . . . . . . . . . . . . . . . 47
8.9. MANAGEMENT OF EXTERNAL MANUAL BYPASS CONTACT . . . . . . . . . . . . . . . . . . . 47
9. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.1. SYSTEM ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.2. UPS ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.3. PREVENTIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
10. TECHNICAL SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

4Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
1.1. IMPORTANT
• This document provides important instructions for the safe use, movement and connection of the Green Power 2.0 uninterruptible
power system (UPS).
• SOCOMEC retains the full and exclusive ownership rights over this document. Only a personal right to use the document for the
application indicated by SOCOMEC is granted to the recipient of this document. The reproduction, modification, distribution of this
document either partially or wholly, and in any way, is strictly prohibited except upon Socomec’s express prior written consent.
• This document is not a specification. SOCOMEC reserves the right to make any changes to the information provided without prior
notice.
• The unit must only be installed and activated by qualified technical personnel who have been authorised by SOCOMEC.
The UPS MUST only be moved by two people at least.
They MUST take position at the sides of the UPS with respect to the direction of movement.
• The unit must remain in a vertical position at all times.
• Connect the PE ground conductor first before making any other connection.
• Do not expose the UPS to rain or liquids in general. Do not insert foreign bodies.
The installer is responsible for implementing the backfeed protection with the use of AC input line isolation devices
external to the UPS (see section 2.4.1).
Before working on this circuit
- Isolate the Uninterruptible Power System (UPS)
- Then check for Hazardous Voltage between all terminals
including the protective earth
Risk of Voltage Backfeed
• For the purpose of warning electrical technicians against backfeed situations not caused by the UPS, which may arise when a
particular load fault is present while the UPS is operating in stored energy mode, or while unbalanced loads are supplied through
a particular power distribution system e.g. an impedance grounded IT system, the installer must attach the labels provided to all
primary power isolators installed remotely from the UPS area and on external access points, if present, between the said isolators
and the UPS. In particular the label must be attached to the external AC input line isolation service (backfeed insulation).
• The UPS may be powered from an IT distribution system with a neutral conductor.
• Keep this manual in a convenient place for future consultation.
• If the unit fails, it must only be repaired by authorised technicians who have been specially trained for this purpose.
• This equipment complies with European Community directives for industrial equipment and bears the approval mark
• The UPS requires three-phase plus neutral input connections (3P+N).
• Do not connect the output neutral to ground. The UPS does not modify the neutral setup of the system; the use of an isolation
transformer is required should it be necessary to modify the neutral setup downstream of the UPS.
• Before connecting any external battery cabinets, ensure they are fully compatible with the UPS model used.
• The use of external battery cabinets not supplied by the manufacturer is not recommended.
• Switch off and isolate the UPS and wait for 5 minutes before removing the protection panels in order to carry out work on parts
under dangerous voltage.
• Risk of explosion if the batteries are replaced with others of the wrong type.
• Used batteries must be disposed of at authorised waste disposal centres.
It is very dangerous to touch any part of the batteries as there is no insulation between the batteries and the mains
power source.
CAUTION!
A battery can present a risk of electrical shock and high short circuit current.
The following precautions should be observed when working on batteries:
1. SAFETY STANDARDS

5
ENGLISH
Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
ENGLISH
1. SAFETY STANDARD
a) Remove watches, rings or other metal objects.
b) Use tools with insulated handles.
c) Wear rubber gloves and boots.
d) Do not lay tools or metal parts on top of batteries.
e) Disconnect the charging source prior to connecting or disconnecting battery terminals.
f) Determine if battery is inadvertently grounded. If inadvertently grounded, remove source from ground. Contact with any part of a
grounded battery can result in electrical shock. The likelihood of such shock can be reduced if such grounds are removed during
installation and maintenance (applicable to equipment and remote battery supplies without a grounded supply circuit).
The product you have chosen is designed for commercial and industrial use only.
If used for particular critical applications such as life support systems, medical applications, commercial transportation, nuclear
facilities or any other application or systems where product failure is likely to cause substantial harm to people or property, the
products may have to be adapted.
For such use please contact SOCOMEC beforehand to check if these products meet the required level of safety, performance,
reliability and comply with applicable laws, regulations and specifications.
1.2. DESCRIPTION OF SYMBOLS USED ON LABELS ATTACHED TO THE UNIT
All precautions and warnings on labels and plates on the inside and outside of the equipment should be observed.
DANGER! HIGH VOLTAGE (BLACK/YELLOW)
GROUND TERMINAL
READ THE USER MANUAL BEFORE USING THE UNIT

6Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
The packaging guarantees the stability of the UPS during shipping and physical transfer. Carry the packaged unit as close as possible
to the installation site.
When moving the unit on even slightly sloping surfaces, use the locking equipment and braking devices to ensure
that the unit does not fall over.
2.1. SHIPPING AND MOVING
• The UPS must remain in a vertical position during all shipping and moving operations.
• The unit has wheels that can be used to move it for short distances.
• Ensure the floor is strong enough to support the weight UPS and battery cabinet, if used.
Avoid pressing on the front panels when moving the unit.
The UPS MUST only be moved by two people at least. They MUST take position at the sides of the UPS with
respect to the direction of movement.
CAUTION IF DAMAGED
NON-SPILLABLE BATTERIES
If packaging is crushed, torn or open such that the inner contents are revealed, the
equipment should be kept in an isolated area and inspected by a qualified person. If the
packaging cannot be shipped the contents should be collected promptly, kept apart, and
the sender or recipient should be contacted.
All packaging must be recycled in compliance with existing legislation in the country where the system is installed.
2. UNPACKING AND INSTALLATION OF THE UNIT
Battery is NOT connected!

7
ENGLISH
Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
ENGLISH
2.2.1-4
2.2.1-5
Secure the UPS with feet C
2. UNPACKING AND INSTALLATION OF THE UNIT
2.2. UNPACKING PROCEDURE
2.2.1. S Models (h 800 mm) and M Models (h 1000 mm)
2.2.1-3 Remove screws A and B
A
B
C
C
2.2.1-1
1
3
2
The UPS can be moved.
Place the UPS in the installa-
tion area.
Secure the UPS with feet D
only when it is in position with
cables connected.
2.2.1-2

8Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
2.2.2-1 2.2.2-2 2.2.2-3
Remove screws Aand B
2.2.2-5
Remove screws A
2.2.2-4
2.2.2-6
Loosen screws B
Remove screws C
2. UNPACKING AND INSTALLATION OF THE UNIT
1B
2C
2.2.2-7
Tighten screws B
2.2.2-8 Secure the UPS with feet D2.2.2-9
Loosen screws B
2B
1
1
The UPS can be moved.
Place the UPS in the installa-
tion area.
D
D
Secure the UPS with feet D only
when it is in position with the
cable connected.
1B
2
2
1
3
2
1A
2
2.2.2. T Models (h 1400 mm)
A
B

9
ENGLISH
Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
ENGLISH
2. UNPACKING AND INSTALLATION OF THE UNIT
2B
1C
2A
1
For UPS 15-40kVA height 1.400mm without internal battery:
• with battery cabinet fitted alongside: remove leveller E from the cabinet. Secure the UPS to the cabinet using the
bracket E provided (figure 2.2.2-12).
• without battery cabinet fitted alongside: secure the UPS to the floor (figure 2.2.2-13).
2.2.2-10
Tighten screws B
Tighten screws C
2.2.2-11
Tighten screws A
Remove the label
2.2.2-14
2.2.2-132.2.2-12
E

10 Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
2. UNPACKING AND INSTALLATION OF THE UNIT
2.3. ENVIRONMENTAL REQUIREMENTS
• The recommended operating temperature, humidity and altitude values are listed in the technical specifications table (see chapter 10).
Cooling systems may be required to maintain these values.
• Avoid dusty environments or areas where there is dust from conductive or corrosive materials (e.g. metal dust or chemical solutions).
• The UPS is not designed for outdoor use.
• Do not expose the UPS to direct sunlight or sources of excessive heat.
• A space of at least 40 cm must be left at the back for adequate ventilation (see figure 2.3-1).
• The UPS switches are accessed from the front; however, a space of at least 1.5 metres should be left at the front of the UPS for
maintenance purposes. It is also advisable to ensure that cable connections are sufficiently long and flexible so that the unit can
be extracted during maintenance (see figure 2.3-2).
• If it is not possible to leave sufficient space at the front, adequate access must be ensured from both sides.
UPS OR
OTHER
CABINET
UPS OR
OTHER
CABINET
UPS OR
OTHER
CABINET
UPS
40 cm1,5 m
UPS
40 cm1,5 m
20 cm20 cm
2.3-1 2.3-2

11
Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
ENGLISH
2. UNPACKING AND INSTALLATION OF THE UNIT
2.4. ELECTRICAL REQUIREMENTS
The installation and system must comply with national plant regulations.
The electrical distribution panel must have a protection and sectioning system installed for the input mains and the auxiliary mains.
If a differential switch is installed on the mains power switch (optional), it must be inserted upstream from the distribution panel.
The table below shows the size of input protection devices recommended for correct installation.
Size of input protection devices
UPS Magneto-thermal input1Magneto-thermal
Aux Mains 1
Differential
input 5
Input/Output cable
core size
Battery cable
core size
Battery
protection
4
(kVA) (A) (A) (A) (mm2) (mm2) (A)
single parallel 2single parallel 2selective type 5Min Max 3Min Max 3
10 3/1
32 40
100 125 0.5
6
35 6 35 50 Gr
100
if common
input mains
125
if common
input mains
16
aux mains
and output
15 3/1
32 40
100 125 0.5
6
35 6 35 50 Gr
100
if common
input mains
125
if common
input mains
25
aux mains
and output
10 3/3 32 40 32 40 0.5 6 35 6 35 50 Gr
15 3/3 32 40 32 40 0.5 6 35 6 35 50 Gr
20 3/3 40 63 40 63 0.5 10 35 10 35 50 Gr
30 3/3 63 80 63 80 0.5 16 35 16 35 100 Gr
40 3/3 80 100 80 100 0.5 25 35 25 35 125 Gr
1Recommended magneto thermal switch: four poles with intervention threshold ≥10 In (curve C). It is necessary to use a D curve selective
breaker if an optional external transformer is used.
2In systems with two or more UPSs operating in a redundant or power parallel configuration.
3Determined by the size of the terminals.
4Protection on the external battery cabinet.
5Caution! Use type B four-pole selective (S) circuit breakers. Load leakage currents are added to those generated by the UPS and during
transitory phases (power failure and power return) short current peaks may occur. If loads with high leakage current are present, adjust the
differential protection. It is advisable in all cases to carry out a preliminary check on the earth current leakage with the UPS installed and opera-
tional with the definitive load, so as to prevent the sudden activation of the above switches.
The UPS is designed for transitory overvoltages in category II installations. If the UPS is part of the building’s electric
circuit or is likely to be subject to transitory overvoltages in category III installations, further external protection must
be provided, either on the UPS or in the AC power supply network to the UPS. Additionally, the ‘surge arrestor’
option, specially designed to protect against residual overvoltages in category III installations, can be installed in the
external manual bypass cabinet. If used, the distance between the UPS and the centralised 4 kV SPD protection
devices type 1 must be Up ≤4kV is ≥15m.
In the event of three-phase distorting loads connected in output, the current on the neutral conductor may have a
value that is 1.5 - 2 times the phase value (also for the input bypass). In this case, size the neutral cables and the input/
output protection adequately.
WARNING!
This is a product for commercial and industrial application in an industrial environment - installation restrictions or
additional measures may be needed to prevent interference.
IMPORTANT!
Protective earthing conductor (PE) must have sufficient current-carrying capacity.
The PE cable core size must be chosen according to the PROTECTIVE CURRENT RATING of the earth circuit which
depends on the provision and location of protective overcurrent devices.

12 Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
2. UNPACKING AND INSTALLATION OF THE UNIT
2.4.1. Backfeed protection
If the UPS does not have an automatic protection device against current backfeed, the operator/installer must add a warning label
to all the mains power disconnecting switches installed at a distance from the UPS area. This serves to remind technicians of the
fact that the circuit is connected to a UPS (see chapter 1 of this manual and paragraph 4.7.3. of the EN62040-1 2009-05 standard).
The label is supplied with the system.
The backfeed protection device may be built into the system (only on specific request), or an electromechanical switch may be
installed externally in the input of the UPS.
• If the UPS incorporates this protection, proceed with the connections as described in paragraph 2.5 of this manual.
• To install the external backfeed protection it is necessary to use the BKF card and an external electromechanical switch that
should be installed. For further information on the connection and the type of remote switch, please read paragraphs 8.8 and 8.9
of this manual.
WARNING!
The neutral is not disconnected as, even in the event of a single fault on the UPS, it never has high potential when
the mains and/or auxiliary power supplies are disconnected upstream. This is to prevent transformation of the power
source to the UPS every time there is a power failure.
If under certain irregular conditions, or due to the installation upstream (e.g. undetected and protected earth fault, or
high leakage in a phase, or with IT systems) there is a hazardous potential on neutral, a suitable isolating switch must
be provided on the neutral as well, or else there must be a detection, signalling and protection system.
NOTE
For equipment with separate Emergency Mains, the neutral of the Emergency Mains line must be electrically common
with the neutral of the main input feed line.

13
ENGLISH
Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
ENGLISH
2. UNPACKING AND INSTALLATION OF THE UNIT
EXT. BATTERYOUTPUT MAINS SUPPLY
L12 L22 L32 N2 L11 L1 L21 L2 L31 L3 N11 N1 +B2 -B2 -B1 +B1
OUTPUT
L12
L22
L32
N2
MAINS
N1
L3
L2
L1
3/3 Connections if
THE MAINS AND AUX MAINS ARE CONNECTED IN COMMON
2.5. INSTALLATION PROCEDURES AND INSTRUCTIONS
WARNING!
Before carrying out work on the terminal board or on UPS internal parts, ensure that the UPS is switched off, remove
the power supply, open the external battery cabinet disconnectors, isolate the system and wait 5 minutes.
Cable specifications:
•strip length: 18 mm
•tightening torque: 2.5 - 4.5 Nm
2.5-1
Set Q1, Q2 and Q6 to the 0 position
2.5-2
Q1 Q2
Q6

14 Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
2. UNPACKING AND INSTALLATION OF THE UNIT
EXT. BATTERYOUTPUT MAINS SUPPLY
L12 L22 L32 N2 L11 L1 L21 L2 L31 L3 N11 N1 +B2 -B2 -B1 +B1
OUTPUT
AUX
MAINS
L12
L22
L32
N2
L11
L21
L31
N11
MAINS
N1
L3
L2
L1
EXT. BATTERYOUTPUT MAINS SUPPLY
L12 L22 L32 N2 L11 L1 L21 L2 L31 L3 N11 N1 +B2 -B2 -B1 +B1
3/3 Connections if
THE MAINS AND AUX MAINS ARE CONNECTED SEPARATELY
EXT. BATTERYOUTPUT MAINS SUPPLY
L12 L22 L32 N2 L11 L1 L21 L2 L31 L3 N11 N1 +B2 -B2 -B1 +B1
OUTPUT
AUX
MAINS
L11
N11
MAINS
N1
L3
L2
L1
L12
N2
3/1 Connections if
THE MAINS AND AUX MAINS ARE CONNECTED SEPARATELY

15
Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
ENGLISH
2. UNPACKING AND INSTALLATION OF THE UNIT
2.5-3 Guide any control cables from the front (RS232, signalling relay contacts, etc.) into the appropriate side cable run A.
2.5-4 Remove the pre-cut element Cand bend elements Bto feed through the cables, secure the terminal board cover with the
four screws.
2.5-5 Secure the cables to the couplings Dlocated on the rack ensuring that the air vents are not obstructed in any way.
2.5-6
Once cabling has been carried out, secure the UPS with the fixing feet E
Note: if the system is installed on a raised floor (such as in a data processing room):
• leave a space of at least 20 cm between the power and the control cables;
• avoid parallel channelling over long distances; choose cables crossing at 90° instead.
2.5-3
2.5-6
L3 N11 N1 +B2 -B2 -B1 +B1
EXT. BATTERY
U
PPLY
A
2.5-4
C
B
EE
2.5-7
A. Power cables
B. Control cables
20 cm
90°
A A
B
B
2.5-5
D
2.6. GENERATOR CONNECTION
If your system uses a generator, connect the ‘generator set ready’ no-potential contact to connector IN 2 on the optional ADC PCB
configured in standard or power safe mode (see paragraph 7.3). This automatically extends the voltage and frequency value range
when power is supplied by the generator set.
2.7. EXTERNAL ESD CONNECTION
A remote emergency shutdown system (ESD) can be installed by means of the optional ADC PCB (see paragraph 7.3). Connect a
normally closed zero-potential contact to terminals IN1+ and IN1- of the ADC PCB.

16 Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
2. UNPACKING AND INSTALLATION OF THE UNIT
2.8. ISOLATION TRANSFORMER
If an external isolation transformer cabinet is required, the following instructions should be followed:
• Refer to chapters 1 and 2 of this manual for indications on moving and installing the cabinet.
• See paragraph 2.4 for details about protection devices.
• The protection cable marked with the ground symbol is connected directly to the distribution panel.
• The transformer can either be connected to the UPS input or output.
The UPS must not operate without the neutral connection to the input.
The transformer cannot be connected to the output on single UPS unit connected in parallel configuration.
For connection details refer to the transformer terminal board diagram.
2.9. UPS PARALLEL CONFIGURATION
2.9.1. General
Parallel connection enhances UPS system reliability, performance and power.
All Green Power 2.0 models can be installed in parallel configuration provided they have the special parallel kit that can be installed
in the factory or later by specialist personnel.
UPS modules for parallel operation are identical to standard UPS modules, as a result safety, shipping and installation recommen-
dations in chapters 1 and 2 also apply.
For 3/1 versions only two units in parallel are allowed.
2.9.2. Installation
UPS units operating in parallel are interconnected using control cables B(fig. 2.9.3-1) and are configured differently depending on
the position they are assigned.
For this reason the units have a position label C(Fig. 2.9.4-1):
• The LEFT label means that the unit must be positioned to the left.
• The RIGHT label means that the unit must be positioned to the right.
• The INTERNAL label (used only on systems with three) means this unit must be positioned between the two other cabinets.
The control cables supplied allow a maximum distance of about 3 metres between the UPS units. This gives enough room for an
external battery cabinet to be inserted beside each UPS.
2.9.3. Power connections
• The power supply to each unit must be protected as indicated in the table in paragraph 2.4.
• The cross section and length of the input and output cables must be identical for all units.
• The phase rotation must be the same for each unit connected in parallel and also on any external manual bypass line.
• Cables of the same length and cross section must be used for the connection between the general power switch A, the switches
Cand the respective UPS units. The length of the cables from A to each UPS module must not exceed 25 metres (Fig. 2.9.3-1).
• The cables from the UPS module to circuit breaker Fmust be of the same length (max. 15 metres) with multi-core cables.
• If a differential switch is installed on the mains power switch (optional), it must be inserted upstream from the distribution panel
(see fig. 2.9.3-1, detail H), it must be a selective type and the trigger value must be 0.5 A multiplied by the number of UPSs
connected in parallel.
Only activate circuit breaker D after carrying out the procedure for switching onto the maintenance bypass.
Only activate circuit breaker E after turning off the UPS.

17
ENGLISH
Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
ENGLISH
2.9.3-1 Recommended parallel configuration
2. UNPACKING AND INSTALLATION OF THE UNIT
Key
ASystem input switch
BParallel bus cable
C
Single UPS magneto-thermal switch (if a
separate auxiliary power source is used, add
a magneto-thermal switch for each UPS)
DExt. bypass magneto-thermal switch
EOutput switch
FSystem shutdown switch
GDistribution
H
Main differential magneto-thermal switch
IInternal UPS
LLeft UPS
RRight UPS
25 m max
• 15-40 kVA: 15 m max
H
A
C C C C C C
D
BBBBB
LIIIIR
EEEEEE
F
G

18 Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
2. UNPACKING AND INSTALLATION OF THE UNIT
2.9.4. Control connections
In order for units connected in a parallel configuration to operate correctly, control cables are required to exchange data between
the various UPS units making up the parallel system, for management of correct load sharing and synchronisation logic.
The cables in question are supplied with the UPS in the case of a standard parallel setup or are attached to the parallel kit in the
case of a later system upgrade.
Parallel configuration must only be activated by SOCOMEC qualified personnel; in each case arrange the control cables in
the relevant cable run as shown in figure 2.9.4-1, leaving the connector(s) unconnected (in the central UPS one incoming and one
outgoing control cable must be used).
A
B
C
Key
AControl cable run
BParallel bus cable; leave approx. 20cm cable length at the exit of the cable run
CLabel for unit positioning
2.10. SPECIAL PARALLEL CONFIGURATION FEATURES
2.10.1. Energy saver
Energy Saver ensures system availability and simultaneously reduces energy consumption. It is available for parallel systems with
more than two units.
Energy Saver can be activated in: HMI MAIN MENU > SETTINGS > UPS SETTINGS > PARALLEL SYSTEM > Energy Saver.
A high speed digital control is used to keep only the units needed to supply the energy to the load in operation. When the power
consumed by the load increases the UPS units needed to supply the increased power requirements switch on immediately.
2.9.4-1

19
Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
ENGLISH
2.10.2-1 UNIT VIEW
2. UNPACKING AND INSTALLATION OF THE UNIT
2.10.2. Intelligent communication module (ICM)
Intelligent Communication Module (ICM) allows the hierarchical supervision both of each unit and the whole system from all displays.
The advantage of using ICM is that the options and external communication accessories for system monitoring and diagnostics (i.e.
Net Vision, ADC board, etc.) can be installed on only one UPS.
In the UPS parallel configuration, an additional navigation bar is displayed on the mimic panel page, where all connected units appear.
To enter the MAIN MENU select the SYS icon and press ENTER.
To enter the UNIT MENU select one of the numbered icons and press ENTER.
2.10.2-2 SYSTEM VIEW
Use the UP/DOWN keys to select
different unit or system mimic panels
SYSTEM view (MAIN MENU)
Selected UNIT number
Units connected in parallel (UNIT MENU)
Icon colours:
same as top bar colours (see 5.2-1)
SYSTEM mimic panel is selected
The SYS icon is selected
The symbol (number surrounded by four lines) indicates the Unit number of the UPS upon which the display is fitted (the display
is fitted on UPS #1 in this example). The BATTERY SETTINGS menu and the Automatic Stop Procedure are only available on
this UNIT MENU.
2.10.3. Sequential start (configurable by Socomec service personnel only)
In a parallel configuration a sequential start can be set in all the units. It allows a reduction of the power impact on the mains or GenSet
when the UPS system resumes from battery mode. The delay restart time (from 0 to 65 seconds) can only be set via ASSIST. The
delay restart rectifier (T_delay_start_rect) has to be the same for each module according to the following specification:
T_delay_start_rect = 5000 ms for each module
Sequential start
Module 1 Module 2 Module 3 Module 4 Module 5 Module 6
Delay time 1x5 s = 5 s 2x5 s = 10 s 3x5 s = 15 s 4x5 s = 20 s 5x5 s = 25 s 6x5 s = 30 s

20 Green Power 2.0 10-40 kVA - Ref.: IOMMASGPXX03-GB 03
2.11-1
L12 L22 L32 N2 L11 L1 L21 L2 L31 L3 N11 N1 +B2 -B2 -B1 +B1
EXTERNAL BATTERY
+B2 –B2 –B1 +B1
EXT. BATTERYOUTPUT MAINS SUPPLY
2.11. EXTERNAL BATTERY CABINET CONNECTION
If the UPS has internal batteries, connecting external battery cabinets is prohibited.
Position the battery cabinet next to the UPS.
Before carrying out any operations, ensure that:
•the battery fuses located inside the battery cabinet are open;
•the UPS is not live;
•all mains or battery switches are open;
•the switches upstream of the UPS are open.
• Remove the terminal boards protection.
• Connect the ground cable (figure 2.11-1).
• Connect the cables between the UPS terminals and the battery cabinet terminals, strictly observing the polarity of each individual
string (figure 2.11-1) and the cross-sections indicated in table 3.4.
Use double insulated cables or the cables supplied with the unit to connect the UPS to the battery cabinet. The
length L of battery cable must not be more than 8 metres long (if L > 8 m, please contact the support service).
Cabling errors with inversion of battery polarity may cause permanent damage to the equipment.
• Replace the terminal board’s protection.
If using cabinets not supplied by the UPS manufacturers, it is the installer’s responsibility to check electrical compa-
tibility and the presence of appropriate protection devices between the UPS and the battery cabinet (fuses and
switches of sufficient capacity to protect the cables from the UPS to the battery cabinet). As soon as the UPS is
switched on (before closing the battery switches) the battery parameters must be verified accordingly (voltage,
capacity, number of elements, etc.) on the mimic panel menu. See 5.3.6 paragraph for battery settings configuration.
2. UNPACKING AND INSTALLATION OF THE UNIT
UPS
BATTERY CABINET