socomec Green Power 2.0 60 User manual

Green Power 2.0
60-80 kVA
Installations- und bedienungsanleitung DE
Installation and operating manual EN
Manual de instalación y uso ES
Paigaldus- ja kasutusjuhend ET
Manuel d’installation et d’utilisation FI
Manuel d’installation et d’utilisation FR
Manuale di installazione e uso IT
Installatie– en bedieningshandleiding NL
Dokumentacja Techniczno-Ruchowa PL
Manual de instalação e funcionamento PT
Manual de instalare şi utilizare RO
Руководство по установке и эксплуатации RU
Navodila za priključitev in uporabo SL
Installations- och användarhandbok SV
Kurulum ve kullanım kılavuzu TR
安装及操作手册 ZH

2Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
This SOCOMEC continuous power system is guaranteed against any manufacturing or material defects.
The warranty is valid for 12 (twelve) months from the commission date, provided activation is carried out by SOCOMEC person-
nel or personnel from a support centre authorised by SOCOMEC, and no more than 15 (fifteen) months from being shipped from
SOCOMEC.
The warranty is valid throughout national territory. If the UPS is exported abroad, the warranty will only cover the parts used to repair
faults.
The warranty is valid ex-works and covers labour and parts used to repair the faults.
The warranty shall not apply in the following cases:
• Failure due to unforeseen circumstances or force majeure (lightning, floods, etc.);
• Failure due to negligence or improper use (use outside limits: temperature, humidity, ventilation, electric power supply, applied
load, batteries);
• Insufficient or inappropriate maintenance;
• When maintenance, repairs or modifications have not carried been out by SOCOMEC personnel, or personnel from a support
centre authorised by SOCOMEC.
• If the battery has not been recharged in accordance with the terms indicated on the packaging and in the manual, in the event of
long periods of storage or UPS inactivity.
SOCOMEC may, at its own discretion, opt for the repair of the product or the replacement of faulty or defective parts with new parts,
or with used parts of equivalent quality to new parts with regard to function and performance.
Defective or faulty parts replaced free of charge must to be made available to SOCOMEC, which becomes the sole owner.
Replacement or repair of parts, or any modifications to the product during the warranty period, will not extend the duration of the
warranty.
SOCOMEC will not be responsible for damages under any circumstances (including, without limitations, damage for loss of earnings,
interruption of activity, loss of information or other financial losses) arising from the use of the product.
These conditions are subject to Italian law. Any disputes fall under the jurisdiction of the Court of Vicenza.
CERTIFICATE AND CONDITIONS OF WARRANTY
SOCOMEC retains the full and exclusive ownership rights to this document. Only a personal entitlement to use the document for the
application indicated by SOCOMEC is granted to the recipient of this document. The reproduction, modification, distribution of this
document, either partially or wholly and in any manner, is strictly prohibited except upon Socomec’s express prior written consent.
This document is not a specification. SOCOMEC reserves the right to make any changes to the information provided without prior
notice.

3
ENGLISH
Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
SUMMARY
ENGLISH
1. SAFETY STANDARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2. DESCRIPTION OF THE SYMBOLS USED ON LABELS ATTACHED TO THE UNIT . . . . . 5
2. INSTALLATION OF THE UNIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1. SHIPPING AND HANDLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2. ENVIRONMENTAL REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3. INTERNAL FRONT VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4. ELECTRICAL DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5. ELECTRICAL REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1. MAINS AND AUX MAINS CONNECTED SEPARATELY. . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2. MAINS AND AUX MAINS CONNECTED TOGETHER . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3. EXTERNAL BATTERY CABINET CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4. MODES OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.1. ONLINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.2. OPERATION IN HIGH EFFICIENCY MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.3. OPERATION IN CONVERTER MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.4. OPERATION WITH INTERNAL MAINTENANCE BYPASS . . . . . . . . . . . . . . . . . . . . . . . . 17
4.5. OPERATION WITH MOTOR GENERATOR (GENSET) . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5. HUMAN MACHINE INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.1. FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2. MIMIC PANEL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3. MENU NAVIGATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6. OPERATING PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.1. SWITCHING ON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.2. COMMISSIONING WIZARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.3. SHUTDOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.4. SWITCHING ONTO MAINTENANCE BYPASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5. SWITCHING ON FROM MAINTENANCE BYPASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.6. EXTENDED OUT OF SERVICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.7. EMERGENCY SHUTDOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.8. UPS GENERAL POWER OFF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7. CONNECTIVITY AND COMMUNICATION OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.1. MULTILEVEL COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.2. STANDARD WEB PAGES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.3. ADC CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
7.4. ADC CARD WITH TEMPERATURE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.5. ISOLATED SERIAL PORT RS232 (DB9 CONNECTION) AND RS485 CARD . . . . . . . . . 36
7.6. REMOTE MIMIC PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.7. NET VISION LAN/WEB INTERFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.8. SOFTWARE OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8. ELECTRICAL OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.1. INTERNAL BACKFEED PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.2. EXTERNAL MANUAL MAINTENANCE BYPASS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
9.1. SYSTEM ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
9.2. UPS ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9.3. PREVENTIVE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10. TECHNICAL SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
11. UPS PARALLEL CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.1. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.2. INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.3. POWER CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.4. PARALLEL SETUP RULES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
11.5. CONTROL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
11.6. PARALLEL CONFIGURATION SPECIAL FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

4Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
1.1. INFORMATION
• This document provides important instructions for the safe use, handling and connection of the Green Power 2.0 uninterruptible
power system (UPS).
• SOCOMEC retains the full and exclusive ownership rights to this document. Only a personal entitlement to use the document for
the application indicated by SOCOMEC is granted to the recipient of this document. The reproduction, modification, or distribution
of this document, either partially or wholly and in any manner, is strictly prohibited except upon Socomec’s express prior written
consent.
• This document is not a specification. SOCOMEC reserves the right to make any changes to the information provided without prior
notice.
• The unit must only be installed and activated by qualified technical personnel who have been authorised by SOCOMEC.
• The unit must remain in a vertical position at all times.
• Connect the protective earth (PE) conductor before making any other connections.
• Do not expose the UPS to rain or liquids in general. Do not insert foreign bodies.
The installer is responsible for implementing the backfeed protection with the use of AC input line isolation devices
external to the UPS (see section 2.5.1).
Before working on this circuit
- Isolate the Uninterruptible Power System (UPS)
- Then check for Hazardous Voltage between all terminals
including the protective earth
Risk of Voltage Backfeed
• For the purpose of warning electrical technicians against backfeed situations not caused by the UPS, which may arise when a
particular load fault is present while the UPS is operating in stored energy mode, or while unbalanced loads are supplied through
a particular power distribution system e.g. an impedance grounded IT system, the installer must attach the labels provided to all
primary power isolators installed remotely from the UPS area and on external access points, if present, between the said isolators
and the UPS.
In particular the label must be attached to the external AC input line isolation service (backfeed insulation).
• Keep this manual in a convenient place for future consultation.
• If the unit fails, it must only be repaired by specially trained authorised technicians.
• This equipment complies with European Community directives for professional equipment and bears the approval mark.
• The UPS requires three-phase plus neutral input connections (3P+N).
WARNING!
As specified in 62040-3 Attachment E: Non-linear Load Reference, in the event of three-phase non-linear loads
connected downstream of the UPS, the neutral current on the load can be 1.5 - 2 times higher than the phase current.
This must be considered when estimating the correct size of the output and auxiliary mains neutral cables.
• The UPS may be powered from an IT distribution system with a neutral conductor.
• Before connecting any external battery cabinets, ensure they are fully compatible with the UPS model used.
• The use of external battery cabinets not supplied by the manufacturers is not recommended.
FOR SERVICE PERSONNEL:
Switch off and isolate the UPS, then wait for 5 minutes before removing the protection panels to carry out work
on parts powered with a dangerous voltage.
The product you have chosen is designed for commercial and industrial use only.
WARNING!
This is a product for commercial and industrial application in the second environment - installation restrictions or
additional measures may be needed to prevent disturbances.
When used for certain 'critical applications', such as life support systems, medical applications, commercial transportation, nuclear
facilities, or any other applications or systems where product failure may cause significant harm to persons or property, the products
may have to be adapted accordingly.
For such uses we would advise you to contact SOCOMEC beforehand to confirm the ability of these products to meet the required
level of safety, performance, reliability and compliance with applicable laws, regulations and specifications.
1. SAFETY STANDARDS

5
ENGLISH
Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
ENGLISH
1. SAFETY STANDARD
1.2. DESCRIPTION OF THE SYMBOLS USED ON LABELS ATTACHED TO
THE UNIT
All interior and exterior precautions and warnings on labels and plates on the equipment should be complied with.
DANGER! HIGH VOLTAGE (BLACK/YELLOW)
PROTECTIVE EARTH TERMINAL (PE)
READ THE USER MANUAL BEFORE USING THE UNIT
We advise you to contact SOCOMEC beforehand to confirm the ability of these products to meet the required level of safety, perfor-
mance, reliability and compliance with applicable laws, regulations and specifications.

6Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
• The packaging guarantees the stability of the UPS during shipping and physical transfer. Carry the packaged unit as close as
possible to the installation site.
2.1. SHIPPING AND HANDLING
• The UPS must remain in a vertical position during all shipping and handling operations.
• Ensure that the floor is strong enough to support the weight of the UPS and battery cabinet, if used.
Avoid pressing the front door when moving the unit
All packaging materials must be recycled in compliance with the laws in force in the country where the system is installed.
2.2. ENVIRONMENTAL REQUIREMENTS
• The recommended operating temperature, humidity and altitude values are listed in the technical specifications table
(see chapter 10). Cooling systems may be required to maintain these values.
• Avoid dusty environments or areas where there is dust from conductive or corrosive materials (e.g. metal dust or chemical solutions).
• The UPS is not designed for outdoor use (see Protection Level on chapter 10).
• Do not expose the UPS to direct sunlight or sources of excessive heat.
• A space of at least 40 cm must be left at the back and 15 cm on both sides for adequate ventilation (see figure 2.2-1 and 2.2-2).
• The UPS switches are accessed from the front; however, a space of at least 1.5 metres should be left at the front of the UPS for
maintenance purposes.
• Do not put any object on top of the UPS.
• A space of at least 80 cm must be left above the UPS (see figure 2.2-3) for maintenance purposes.
2. INSTALLATION OF THE UNIT
2.2-1 2.2-2 2.2-3
≥ 80 cm
15 cm 15 cm 15 cm
15 cm
free area
UPS
or
BATTERY
CABINET
40 cm
UPS
or
BATTERY
CABINET
40 cm
UPS
or
BATTERY
CABINET
40 cm
1,5 m
130°
door
free area
UPS
40 cm
1,5 m
130°
door
15 cm 15 cm

7
Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
ENGLISH
2. INSTALLATION OF THE UNIT
2.3. INTERNAL FRONT VIEW
Key
AUSB connector
BLAN RJ45 connector for ethernet
CSerial RS232/485 connector
DSerial RS232 connector for modem
ECable run
FSlots for optional cards
GFuse + output socket for options
HFans
IFans
J Power connections (behind the plastic protection)
Q1 Input breaker (MAINS SUPPLY)
Q3 Output breaker (emergency shutdown ESD)
Q4 Aux mains breaker
Q5 Manual maintenance bypass
H
I
F
E
G
E
Q1 Q4 Q5 Q3
J
AC
BD
E
Cable ties
Locking cable clamp
(not provided)
E
1
2
Handle interlocking
(position 0)

8Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
2. INSTALLATION OF THE UNIT
2.4-1 Electrical diagram
2.4. ELECTRICAL DIAGRAM
The following is a simple electrical diagram of the UPS unit.
For connections details see chapter 3.
PE BATTERY
MAINS
BKF
AUX
BKF UPS OUTPUT OPTIONS SOCKET
INPUT MAINS AUXILIARY MAINS
UPS

9
Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
ENGLISH
2. INSTALLATION OF THE UNIT
2.5. ELECTRICAL REQUIREMENTS
The installation and system must comply with national plant regulations.
The electrical distribution panel must have a protection and sectioning system installed for the input mains and auxiliary mains.
Use a differential switch (type B) installed on the mains power switch, which must be inserted upstream from the distribution panel.
The table below shows the input protection devices recommended for the correct installation of an individual UPS.
The maximum cable sizes allowed are also included in the table.
Size of input protection devices
Model
rating
Magneto-
thermal Input(1)
Magneto-
thermal Aux.
Mains(1)
Differential
input(4)
Input/Output
cable
core size
Aux cable
core size
Battery cable
core size
Battery
protection(3)
(kVA) (A) (A) (A) (mm2) (mm2) (mm2) (A)
single parallel single parallel flexible
cable
rigid
cable
flexible
cable
rigid
cable
flexible
cable
rigid
cable
max(2) max(2) max(2) max(2) max(2) max(2)
60 125 160 125 160 0,5 50 70 95 95 95 95 200 aR
80 160 200 160 200 0,5 50 70 95 95 95 95 200 aR(5)
(1) Recommended magneto-thermal switch: four poles with intervention threshold curve C. It is necessary to use a D curve selective breaker if
an optional external transformer is used.
(2) Determined by the size of the terminals.
(3) Protection on the external battery cabinet.
(4) Caution! Use type B four-pole selective (S) circuit breakers. Load leakage currents are added to those generated by the UPS and during
transitory phases (power failures and power returns) short current peaks may occur. If loads with high leakage current are present, adjust
the differential protection. It is advisable in all cases to carry out a preliminary check on the earth current leakage with the UPS installed and
operational with the definitive load, so as to prevent the sudden activation of the above switches.
(5) Use 250aR for a battery cabinet with capacity exceeding 90 Ah.
The UPS is designed for transient overvoltages in category II installations. If the UPS is part of the building’s
electrical circuit, or is likely to be subject to transient overvoltages in category III installations, additional external
protection must be provided, either on the UPS or in the AC power supply network powering the UPS.
GENSET must support load variations from 0 to 100%.
WARNING!
As specified in 62040-3 Attachment 3: Non-linear Load Reference, in the event of three-phase non-linear loads
connected downstream of the UPS, the neutral current on the load can be 1.5 - 2 times higher than the phase current.
This must be considered when estimating the correct size of the output and the auxiliary neutral cables.
WARNING!
This is a product for commercial and industrial application in an industrial environment - installation restrictions or
additional measures may be needed to prevent interference.
IMPORTANT!
Protective earthing conductor (PE) must have sufficient current-carrying capacity.
The PE cable core size must be chosen according to the PROTECTIVE CURRENT RATING of the earth circuit which
depends on the provision and location of protective overcurrent devices. We suggest 35 mm2for GP80 and 25 mm2
for the Green Power 2.0 using the protective devices in the above table.

10 Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
2.5.1. Backfeed protection
The UPS can control two external (optional internal) power isolation devices against the backfeed of dangerous voltages, one for the
input line (MAINS SUPPLY) and the other for the auxiliary line (AUX MAINS SUPPLY). The external devices have to be connected to
the terminals as shown in figure 2.5.1-1 (COM1, NC1, COM2, NC2).
Warning labels must be attached to all mains power disconnectors installed away from the UPS area, in order to remind service
personnel that the circuit is connected to a UPS (see also section 1.1 Warnings in this manual and section 4.7.3 of standard CEI EN
62040-1 2009-05). The labels are supplied with the equipment.
Beware: if there is a hazardous potential on neutral under certain irregular conditions, or due to the installation upstream (e.g. unde-
tected and protected earth fault, high leakage in a phase, or with IT systems), a suitable isolating switch must be provided on the
neutral as well, or else there must be a detection, signalling and protection system (see paragraph 2.5).
2. INSTALLATION OF THE UNIT
2.5.1-1
+B2 -B2 -B1
COM1 NC1 NC2 COM2
BKF
Function Connector name V OUT Internal fuse Detail
BKF AUX XB2 230 V RMS 2 A time delay COM 2(1)
NC2
BKF MAIN XB3 230 V RMS 2 A time delay COM1(1)
NC1
(1) COM1 and COM2 are connected to the neutral.
Refer to the following paragraph for details on electrical connection.

11
ENGLISH
Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
ENGLISH
2.5.2-3 Separate Mains
2.5.2-1
B
L1
L2
L3
XB5 - XB6
N
2.5.2. Connecting the external backfeed protection
To ensure maximum protection, use a 220-240 V
release coil with integrated travel limit contact to pilot
the input protection systems (see section 2.5
“Electrical requirements”). If a trip coil without an
integrated end-of-travel contact is used, add an
early auxiliary contact as shown in figure 2.5.2-1.
Electrical contact data: 2 A 250 Vac
• Protection with Mains and Aux Mains connected separately
Activating UPS protection: access the MAIN MENU > SETTINGS > UPS SETTINGS > BACKFEED and set the BACKFEED TYPE
Parameter to SEPARATE MAINS.
L1
L2
L3
N
L1
L2
L3
N
X10
B
L11
L21
L31
N1
L11
L21
L31
N1
XB3
XB2
X40
T1
T2
B
AKey
ADistribution panel
BTrip coil
X10 Mains terminal block
X40 Aux Mains terminal block
T1 Mains switch
T2 Aux Mains switch
XB2 Aux Mains BKF connector
XB3 Mains BKF connector
See also section 3.1
MAINS
UPS
BKF
AUX MAINS
2. INSTALLATION OF THE UNIT

12 Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
2.5.2-4 Common Mains
L1
L2
L3
N
X10
A
L1C
L2C
L3C
NC
L11
L21
L31
N1
XB3
XB2
X40T1
B
Key
ADistribution panel
BTrip coil
X10 Mains terminal block
X40 Aux Mains terminal block
T1 Mains switch
XB2 Not connected
XB3 Mains BKF connector
See also section 3.2
Remote switches - rated current
Model T1 T2
60 3/3 125 A AC1 125 A AC1
80 3/3 160 A AC1 160 A AC1
UPS
BKF
COMMON MAINS
2. INSTALLATION OF THE UNIT
• Protection with Mains and Aux Mains connected together
Activating UPS protection: access the MAIN MENU > SETTINGS > UPS SETTINGS > BACKFEED and set the
BACKFEED TYPE Parameter to COMMON MAINS.

13
ENGLISH
Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
ENGLISH
20 cm
90°
3-2 For systems installed on raised floors
3-1 Power connections
A. Power cables
B. Control cables
Cable specifications:
• strip length: 18 mm
• tightening torque: 3.5 - 4.5 Nm
Protective
Earth terminal (PE)
(see sec. 2.5 )
A
B
B
A
3. CONNECTIONS
+B2
COM1 NC1 NC2 COM2
+B1-B2 -B1 L1 L11 L21 L31L2 L3 N N1 L12 L22 L32 N2
M8
Ø 8
BKF
EXT.
BATTERY
AUX
MAINS
MAINS OUTPUT

14 Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
3. CONNECTIONS
3.1. MAINS AND AUX MAINS CONNECTED SEPARATELY
3.2. MAINS AND AUX MAINS CONNECTED TOGETHER
+B2
COM1 NC1 NC2 COM2
+B1-B2 -B1 L1 L11 L21 L31L2 L3 N N1 L12 L22 L32 N2
+B2
COM1 NC1 NC2 COM2
+B1-B2 -B1 L1 L11 L21 L31L2 L3 N N1 L12 L22 L32 N2
3.1-1
3.2-1
MAINS LOAD
LOAD
AUX
MAINS
MAINS
Max 50 mm2(flexible)

15
ENGLISH
Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
ENGLISH
3. CONNECTIONS
3.3. EXTERNAL BATTERY CABINET CONNECTION
Position the battery cabinet next to the UPS.
Before performing any operations ensure that:
• the UPS is not operating,
• all mains or battery switches are open,
• the switches upstream of the UPS are open,
• the battery fuses located inside the battery cabinet are open.
• Remove the plastic terminal block protection.
• Connect the protective earth (PE) cable (figure 3.3-1).
• Connect the cables between the UPS terminals and the battery cabinet terminals, strictly observing the polarity of each individual
string (figure 3.3-1) and the cross-sections indicated in the table (see chapter 2.5).
Use the cables supplied with the unit to connect the UPS to the battery cabinet.
Cabling errors with inversion of battery polarity may cause permanent damage to the equipment.
• Reassemble the plastic terminal block protection.
If using cabinets not supplied by SOCOMEC, it is the installer’s responsibility to check electrical compatibility and
the presence of appropriate protective devices between the UPS and the battery cabinet (fuses and switches of
sufficient capacity to protect the cables from the UPS to the battery cabinet). As soon as the UPS is switched on
(before closing the battery switches) the battery parameters (voltage, capacity, number of elements, etc.) must be
verified accordingly on the HMI menu. If the values indicated on the battery cabinet data plate are different from
those shown on the HMI menu, use the BATTERY SETTINGS (see chapter 5.3.6) menu to correct the settings. Not
all battery/capacity combinations are available!
+B2
COM1 NC1 NC2 COM2
+B1-B2 -B1 L1 L11 L21 L31L2 L3 N N1 L12 L22 L32 N2
+B2 –B2 –B1 +B1
M10
M8
Ø 10
Ø 8
3.3-1
BATTERY CABINET
BATTERY CABINET
EXTERNAL BATTERY
EXTERNAL BATTERY
UPS
UPS
For the Protective Earth (PE) cable core size see the battery cabinet installation manual.

16 Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
4.1. ONLINE OPERATION
A special feature of the Green Power 2.0 series is the ONLINE double conversion in conjunction with low distortion mains power
absorption. In Normal Mode (on inverter), the UPS can supply a voltage that is fully stabilised in frequency and amplitude, regardless
of any interference in the mains power supply, within the most stringent classification of UPS regulations.
ONLINE operation provides three operating modes according to mains and load conditions:
• Inverter mode
This is the most frequent operating condition: energy is drawn from the primary mains power supply and converted and used by
the inverter to generate the output voltage to power the connected loads.
The inverter is constantly synchronised in frequency with the auxiliary mains to enable load transfer (due to an overload or inverter shutdown)
without any break in the power supply to the load.
The battery charger supplies the energy required to maintain or recharge the battery.
• Bypass mode
In the event of inverter failure, the load is automatically transferred onto the auxiliary mains without any interruption in the power supply.
This procedure may occur in the following situations:
- in the event of a temporary overload, the inverter continues to power the load. If the condition persists, the UPS output is switched
on to the auxiliary mains via automatic bypass. Normal operation, which is from the inverter, returns automatically a few seconds
after the overload disappears.
- When the voltage generated by the inverter goes outside the limits due to a major overload or a fault on the inverter.
- When the internal temperature exceeds the maximum value allowed.
• Battery mode
In the event of a mains failure (micro interruptions or extended power cuts), the UPS continues to power the load using the energy
stored in the battery.
4.2. OPERATION IN HIGH EFFICIENCY MODE
The UPS has a selectable, programmable economy operating mode (ECO MODE) that can increase overall efficiency by up to 99%
for energy saving purposes. If the power supply fails, the UPS will automatically switch onto the inverter and continue to supply
power to the load by drawing energy from the battery.
This mode does not provide perfect stability in frequency and voltage like the NORMAL MODE. Therefore the use of this mode
should be carefully evaluated according to the level of protection required by the application.
With the optional board Net Vision (see chapter 7.7) specific daily or weekly time intervals can be selected and programmed to power
applications directly from the auxiliary mains.
ECO MODE operation provides very high efficiency, since the application is powered directly from the auxiliary mains via the auto-
matic bypass under normal operating conditions.
To activate ECO MODE go to MAIN MENU > COMMANDS > ECO MODE and select ACTIVATE ECO MODE. To disable ECO
MODE, select RETURN TO NORMAL MODE.
4. MODES OF OPERATION

17
Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
ENGLISH
4. MODES OF OPERATION
4.3. OPERATION IN CONVERTER MODE
In converter mode the UPS can supply a fully stabilised sinusoidal output voltage with a different frequency from the input power
line (50Hz or 60Hz is available as output frequency value).
IMPORTANT!
Only set this mode on UPS units with the auxiliary mains (AUX MAINS) disconnected!
Do not set this mode on UPS units with common mains lines as it could damage the load!
4.4. OPERATION WITH INTERNAL MAINTENANCE BYPASS
If the internal maintenance bypass is activated using the appropriate procedure, the load is powered directly from the maintenance
bypass, while the UPS is separate from the power supply and can be switched off.
This operating mode can be selected for maintenance to be carried out on the system, so that the necessary actions can be
performed by service personnel without having to disconnect the power supply to the load.
4.5. OPERATION WITH MOTOR GENERATOR (GENSET)
Green Power 2.0 can be operated in conjunction with a generator (GENSET) over the ADC interface (see chapter 7.3).
With a generator, the frequency and voltage ranges of the auxiliary mains can be increased to accept the instability of the GE and at
the same time to avoid operation from the battery or risks of out-of-synchronisation switching on to the bypass.

18 Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
5. HUMAN MACHINE INTERFACE
5.1. FOREWORD
The HMI (Human Machine Interface) on the UPS door displays information regarding operating status, electrical measurements,
access to control functions and configuration parameters. It includes a colour graphic display and a luminous status bar, and
provides access to:
• mimic panel;
• measurements and alarms;
• changing UPS operating modes and programming battery tests;
• assisted startup and switching on maintenance bypass procedures;
• settings menu;
• list of events and statistics.
5.1-1
Display
ESC button
Exits current page,
aborts operations.
UP button
Scrolls up through the
available menus/values.
UP/DOWN button
Scrolls down through the
available menus/values.
ENTER button
Accesses the currently
displayed menu, accepts/
sends configurations and
commands.
Luminous status bar
Changes colour according to UPS status.
- Flashing red: imminent UPS shutdown
- Red: Load not powered or battery circuit open
- Flashing yellow: UPS in standby mode or maintenance alarm is active
- Yellow: UPS on battery or the UPS points out a particular working mode
- Flashing green: battery test is in progress
- Green: the load is supplied
- O: inactive UPS

19
Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
ENGLISH
5. HUMAN MACHINE INTERFACE
5.2. MIMIC PANEL OVERVIEW
5.2-1 Status bar (always displayed)
UPS Rated Power (kVA)
Unit panel reference
Operating modes:
Normal (Normal mode), Eco (Eco mode), En. Saver (Energy
Saver mode – parallel configurations only), Standby (Standby
program mode), Service.
Unit status:
• Displayed messages: ON MAINT. BYPASS, IMMINENT STOP,
ON BATTERY, BATTERY TEST, ON INVERTER, ON AUTO
BYPASS, UNIT AVAILABLE, UPS IN STANDBY, LOAD OFF.
- Flashing red: imminent UPS shutdown
- Red: Load not powered or battery circuit open
- Flashing yellow: UPS in standby mode or maintenance alarm
is active
- Yellow: UPS on battery or the UPS points out a particular
working mode
- Flashing green: battery test is in progress
- Green: the load is supplied
- Grey: inactive UPS
5.2-2 Alarms area
Alarms area
Present when an alarm is active.
Enter ALARMS menu to display the complete alarms list (see chapter 9).
5.2-3 Status icons
Key icon:
Displayed if the keypad has been locked.
Time:
UPS current time (hours and minutes, with ':' flashing).
USB icon:
Displayed if a USB memory stick is inserted.
It must be formatted with FAT32 filesystem.
Network icon:
Displayed if a valid link has been established on the ethernet.
Flashes when a remote host is communicating with the UPS.
Foreword: status icons and Time are only visible if there are no pending
alarms, as the alarm bar overwrites the icons when active.

20 Green Power 2.0 60-80 kVA - Ref.: IOMMASGPXX06-EN 06
5. HUMAN MACHINE INTERFACE
Keypad locking
The keypad can be locked by pressing the buttons in the following sequence:
ESC UP DOWN ENTER
To unlock the keypad, the buttons must be pressed in the reverse sequence:
ENTER DOWN UP ESC
These sequences work only on Mimic Panel page.
5.2-6 Load level
œ œ œ œ œ
œ œ œ œ ! Green
Yellow
5.2-4 Additional Icons
On Maintenance Bypass
Commissioning Code not inserted (see chapter 5.3.9)
or Scheduled Inspection warning: machine inspection required
call SOCOMEC support service
Operating on GenSet
Bypass mode (or Eco Mode) not possible
5.2-5 Mimic panel
Bars
1. Rectifier input.
2. Rectifier output.
3. Inverter Input or Battery Output.
4. Inverter Output.
5. Unit output.
6. Output from static switch
7. Bypass input.
Bar colour identify the energy flow:
• blue: active/mains present
• grey: mains not present
67
5
321 4