SolarEdge SEXXXXH-RWMBNBF54 User manual

SolarEdge
Home Hub Inverter -Single Phase
Quick Installation Guide
for Europe models SEXXXXH-RWMBNBF54
A
solaredge.com
SolarEdge Technologies GmbH, Werner-Eckert-Str. 6, 81829 Munich, Germany
Subject to change without notice.
© SolarEdge Technologies, Ltd.
All rights reserved. July 2023. Rev 1.2
Mounting
Drill Level
Phillips/Flat-
Blade
screwdriver set
Small Flat-Blade
(2mm)
Screwdriver
Hammer
Pencil Wire Cutter
Mounting screws and
wall plugs -max M10
min 2
Tools and Materials
What’s in the Package
CAUTION! Denotes a hazard. It calls attention to a procedure that, if not correctly
performed or adhered to, could result in damage or destruction of the product. Do not
proceed beyond a caution sign until the indicated conditions are fully understood and met.
WARNING!
This symbol denotes a hazard. It calls attention to a procedure that if not correctly
performed or adhered to could result in injury or loss of life. Do not proceed beyond
a warning note until the indicated conditions are fully understood and met.
Inverter Wall mount bracket SolarEdge Home
Network Antenna
Torque wrench
with 4 mm Allen bit
Open-end 10mm
torque wrench
Optional
Holes
Ø 9mm
1
CAUTION! DO NOT rest the inverter vertically on the connectors
2
3
4 N*m
Optional
4
40 cm
10 cm
20 cm
20 cm
20 cm
20 cm
MC4crimper
PV String(s)
WARNING! Connect the grounding wire first
WARNING! HAZARD OF ELECTRIC SHOCK.
DISCONNECT POWER BEFORE INSTALLATION OR SERVICE
6
BWiring
SolarEdge Home Battery 400V
2
3
7
WARNING! Connect a
ground cable if required
by local regulation.
5
6 N*m
WARNING! To avoid danger, read the HANDLING AND SAFETY
INSTRUCTIONS provided with this product, or refer to:
https://www.solaredge.com/sites/default/files/se_handling_and_saf
ety_instructions.pdf
1-10 mm2
18 mm
60 mm
9-21 mm
1
2
4
3
6
5
1
2
3
4
Before installation, read the datasheet provided with this
product, or refer to: https://knowledge-
center.solaredge.com/sites/kc/files/se-home-hub-single-phase-
inverter-datasheet-eu.pdf
WARNING! Make sure to use a
protective device with a rating of 28A
(50A for SE8000H and above).
Do NOT connect a protective device
with a higher rating than 50A (80A for
SE8000H and above).
NOTE: Use a protective device
according to regulation
4 N*m
L N GND
AC Grid 1
Important Note: This PV
string is only available for
models SE8000H and above

1.5 N*m
Connecting to Backup Interface
LED Indications
•Red: fault
•Green: power production,
•Blinking Green: Grid connection ok
•Blue: communication ok
For more indications refer to:
https://www.solaredge.com/leds
Commissioning the Inverter
SetApp
ON
1
Run SetApp and
follow the instructions
on the screen
4 N*m
I
For remote status, fault indications,
and system performance,
refer to Remote Monitoring at:
https://www.solaredge.com/products/pv-monitoring#/
IMPORTANT! The connection to units and accessories shown here is for reference only.
For detailed information, refer to the specific product guide.
WARNING! Before installing or operating SolarEdge Home Battery 400V, read
the safety and handling instructions provided with the battery.
F
G
C
4
P(Hold and release within 2 seconds)
P 1 0 5
6
Backup Interface
Communication Cables (CAT 5e/6)
5.5 N*m
Connecting to SolarEdge Home Network
SolarEdge home network plug-in and antenna are pre-installed in this product.
Connecting Multiple Inverters
SolarEdge Home
Battery 400V
2
P(Hold and release
within 2 seconds)
P
3
D
Connecting to SolarEdge Home Battery 400V
Optionally, connect battery communication wirelessly using SolarEdge Home Network
IMPORTANT! If wired communication is used, remove the SolarEdge Home Network plugin
before making wire connections. Reinstall the Plug-in after commissioning the inverter.
Power Cables
Ground Cable, 6-10 mm2
Communication Cables (CAT 5e/6)
G A B
1.5 N*m
SolarEdge Home
Battery 400V
5.5 N*m
WARNING!
Connect a
ground cable
according to local
regulation
requirements. For
connection,
See section A.
Leader Inverter
Connecting to LAN or Wi-Fi
In Leader/Follower configuration, LAN or Wi-Fi MUST connect to the Leader inverter
RS485 Cable (CAT 5e/6)
Leader (first) Follower (last)
Follower
1.5 N*m
Communication
Board
SW2
5.5 N*m
14
3
6
5
1
2
3
4
2
J
H
Connecting Meter and Rapid Shutdown (RSD) Switch
IMPORTANT! Remove the SolarEdge Home Network Plugin before making wire
connections. Reinstall the plug-in after commissioning the inverter.
ON
5.5 N*m
1.5 N*m
External Rapid
Shutdown (RSD)
Switch (Not included)
RSD Switching
of Multiple
Inverters
G A B 12-12+
G A B 12-12+
SW2
SW2
1.5 N*m
RSD
G En A B
12V
+ -G A B
RSD
-+RS485
G A B
1.5 N*m
RS485
B A G
Battery
This port is for SolarEdge or 3rd party
meters (Modbus protocol)
Important! Verify that all switches
are down.
RS485-1
RS485-1
RS485-2
RS485-2
B A G
RS485
B A G
RS485
B A G
RS485
RS485-1
Meter Connection
E
Inline Meter
Smart Energy Hot Water
SolarEdge Home Battery 400V
Optional
Location SolarEdge Home
Network Plugin
Ethernet Cable
Router
5.5 N*m
1.1 N*m
Optional
Location
LAN
Wi-Fi
Wi-Fi Router
NOTE: Wi-Fi antenna is optional
and may be purchased separately.
Follower
Inverter
Follower
Inverter
Leader
Inverter