SolarEdge Home Hub Inverter Three Phase User manual

SolarEdge
Home Hub Inverter -
Three Phase
Quick Installation Guide
For Europe, APAC and South Africa
A
solaredge.com
SolarEdge Technologies GmbH, Werner-Eckert-Str. 6, 81829 Munich, Germany
Subject to change without notice.
© SolarEdge Technologies, Ltd.
All rights reserved. March2023.
Mounting
Datasheet Installation Guide
BWiring
Drill Level
Phillips/Flat-Blade
screwdriver set
Small Flat-Blade
Screwdriver
Hammer
Pencil
Wire Cutter
Mounting screws and
wall plugs -max M10
min 2
Tools and Materials
What’s in the Package
CAUTION! Denotes a hazard. It calls attention to a procedure that, if not correctly performed or adhered to,
could result in damage or destruction of the product. Do not proceed beyond a caution sign until the indicated
conditions are fully understood and met.
WARNING!
This symbol denotes a hazard. It calls attention to a procedure that if not correctly performed or adhered
to could result in injury or loss of life. Do not proceed beyond a warning note until the indicated
conditions are fully understood and met.
Crimping tool
Inverter
Wall mount bracket SolarEdge Home
Network Antenna
Torque wrench
with 10 mm socket hex
and 5 mm Allen bit
Antenna
bracket
DC connection
box
20 cm
10 cm 10 cm
20 cm
2
3
1
4 N*m
CAUTION! Do not
block airflow
37 KG
CAUTION! DO NOT rest
the inverter vertically on
the connectors
4
5
Open-end
torque
wrench
6
Ferrite
Bead
Optional antenna location
Wiring Video
Unpacking and
Mounting Video
Cable lugs
3
WARNING! HAZARD OF ELECTRIC SHOCK. DISCONNECT
POWER AND WAIT FOR 5 MINUTES BEFORE INSTALLATION OR
SERVICE
CAUTION! DO NOT
use a circuit breaker
with a rated current
of more than 16A
WARNING! connect the grounding wire first
8 mm
100 mm
15-21 mm
Ferrule
(For stranded wires) 2.5-16 mm2
1
7
5
9
3
4
10
6
8
2
WARNING! Before installing or operating the Inverter, read
the Safety and Handling instructions provided with this product.
Optional
2DC 5
PV String(s)
WARNING! Connect a
ground cable according
to local regulation.
L1 L2 L3 N
4AC
1.5 N*m
OFF
1

Backup
interface
G A B + 12 -
G A B 12-12+
EChaining Multiple Inverters
LED Indications
•Red: fault
•Green: power production,
•Blinking Green: Grid connection ok
•Blue: communication ok
For more indications refer to:
https://www.solaredge.com/leds
F
Commissioning the Inverter
SetApp
2
4
ON
P 1 0
P(Hold for 5 seconds and release)
3
11
7
5
9
3
4
10
6
8
2Run SetApp and
follow the instructions
on the screen
4 N*m
I J
For remote status, fault indications, and system
performance, refer to Remote Monitoring at:
https://www.solaredge.com/products/pv-monitoring#/
RS485-2
Communication Board
G A B
SW1 SW2
1.5 N*m
CAT5e/6 cable
G
Meter Connection (In case BUI is used, Meter shall be connected via
Backup Interface. Inline meter can also be connected wirelessly)
Meter
G A B
1.5 N*m
CAT5e/6 cable
Battery Connection
D
Battery
communication
(CAN)
1
G A B G A B G A B
SW2
CAT5e/6 cable
Leader (first) Follower (last)
CSolarEdge Home Network Connection
1.1 N*m Inline Meter
1.5 N*m
LAN Connection
Ethernet Cable
Router
CAT5e/6 cable
H
LAN cable
NOTE: In Leader-Follower
configuration, LAN MUST
connect to Leader
Follower
Backup Interface Connection
SW2
SW2
2
4
8N*m
Max cables length 5 m
Communication Cable
Ground Cable
IMPORTANT! The connection to units and accessories shown here is for reference only. For detailed information, refer to the specific product guide.
Smart
Energy Hot
Water
2.2 N*m
+
-
3
“Click!”
5