Soleus Air KY-34 User manual

Portable Air Conditioner,
Dehumidifier,Heater and
Fan
utilizing Heat Pump Technology
OWNER'S MANUAL
Model # KY-34
Please read owner’s manual carefully before operating unit.
3046364

2
TABLE OF CONTENTS
INTRODUCTION.............................................................................................................................................................3
IMPORTANTSAFEGUARDS.......................................................................................................................................4
LCDI POWER CORD AND PLUG.................................................................................................................................5
PRODUCT DIAGRAM ....................................................................................................................................................6
INSTALLATION...............................................................................................................................................................7
CONTROL PANELAND MULTI-COLOR DISPLAY .................................................................................................9
CONTROL PANEL FUNCTIONS ................................................................................................................................10
OPERATION USING THE CONTROL PANEL .........................................................................................................10
COOLING.....................................................................................................................................................................10
DEHUMIDIFYING ......................................................................................................................................................11
FANNING.....................................................................................................................................................................11
HEATING.....................................................................................................................................................................11
AUTO MODE...............................................................................................................................................................11
SLEEPMODE ..............................................................................................................................................................12
REMOTE CONTROL & OPERATION.......................................................................................................................12
MAINTENANCE............................................................................................................................................................14
END OF SEASON STORAGE.....................................................................................................................................14
TROUBLESHOOTING..................................................................................................................................................15
ERROR MESSAGES....................................................................................................................................................15
TECHNICAL SPECIFICATIONS ................................................................................................................................16
DISCLAIMER.................................................................................................................................................................16
WARRANTY ...................................................................................................................................................................17

3
INTRODUCTION
Thank you for purchasing the Soleus Air KY-34 14,000 BTU Portable Air Conditioner and Heater. This
unit is designed to improve indoor living and working comfort by providing cooling, dehumidifying, heating,
and ventilation with minimal installation.
This multi-functional unit operates as an air conditioner, dehumidifier, heater, and fan. Unlike traditional
portables, there is no bucket to empty. The condensate water is evaporated and removed through the exhaust
duct along with the warm exhaust air. When operating as an air conditioner, this unit is designed for spot
cooling or cooling a room no larger than 550 square feet with a standard eight foot ceiling height. When
using this appliance, always exercise basic safety precautions.
Other air conditioning methods are recommended when the indoor temperature is either below 64°F or above
86°F.
Please complete the following information for future reference. Retain this owner’s manual with your sales
receipt as a permanent record of your purchase.
Serial Number: _________________________________________________________
Date of Purchase: _______________________________________________________
Place of Purchase: _______________________________________________________

4
IMPORTANT SAFEGUARDS
Before installing and using your portable air conditioner and heater, it is important that you read this owner’s
manual carefully. Store this manual in a safe place for future reference.
This instruction manual is used for guidance and does not form part of a contract. It reserves the right to
make technical changes without prior notice.
1. Always place the unit on a level surface.
2. The appliance shall be installed in accordance with national wiring regulation.
3. The unit must be connected to a correctly grounded power supply. For your safety, this unit is
grounded through the power cord plug when connected to a grounded wall outlet. Do not use an
adapter plug or extension cord.
4. Do not install the unit in an area where gas leakage may occur and/or in an explosive atmosphere.
5. Do not apply an insecticide or any type of flammable spray on the unit.
6. Confirm drainage piping is connected properly.
7. Do not start or stop the unit by inserting or pulling out the power plug.
8. Do not operate with wet hands.
9. Close supervision is necessary when the unit is used near children. The unit in not intended for use
by children.
10. Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills.
11. Do not expose skin or eyes directly to cool air for a long period of time.
12. If an abnormal odor or smoke comes out of the unit, disconnect the unit immediately and contact a
qualified service technician. (see page 13)
13. When opening the filter cover, do not touch the metal parts in the unit’s interior.
14. Do not immerse the unit in water or any type of liquid. Do not use the unit in the immediate
surroundings of a bath, shower, or swimming pool, or in any other steamy, wet areas.
15. When cleaning the unit, always turn the unit off and unplug the power cord.
16. Always inspect the power cord for signs of damage before use. If the power cord is damaged, it must
be replaced by the manufacturer or a qualified service technician.
17. Do not place a plant or allow a pet in the direct path of the airflow to avoid injury.
18. Do not put a stove, etc, where it would be exposed to the direct airflow. It may affect combustion.
19. Do not sit on the unit or place anything on it.
20. Before storing, the water must be drained from the unit and the filters cleaned.

LCDI POWER CORD AND PLUG
This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and
plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord
with no termination on the load side and a LCDI attachment plug on the line side.
The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the
nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.
The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the
risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they
must be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any
exposed metal.
The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:
1. Plug power cord into wall outlet
2. Press TEST Button, circuit should trip, cutting power to the air conditioner
3. Press RESET button for use
If a test is performed and the indicator light remains ON, current leakage has been detected. Do not use the
air conditioner or attempt to reset the LCDI Plug. Contact SoleusAir Customer Service for troubleshooting
recommendations.
WARNING:
1. DO NOT press the TEST button while the air conditioner is operating.
2. The TEST and RESET buttons should not be used as “ON”and “OFF”switches.
3. The cord and plug are not intended to offer protection to externally connected loads or supply
circuits.
4. The cord and plug are intended for indoor use only.
5

PRODUCT DIAGRAM
FRONT
A. Control panel
B. Vertical air louvers
C. Air outlet
D. Horizontal air louvers
E. Casters
F. Cable (power cord and plug)
BACK
A. Hot air outlet grill
B. Lower air inlet grill
ACCESSORIES
Flexible exhaust hose with adapters
• 3-piece set
• stretches from 14 1/4” to 60 5/8”
(36cm to 150cm)
Window exhaust adapter
Adjustable window slider kit
• 2-piece set
• adjusts 33 1/2” to 48 3/8” (85cm to 123cm)
Drain tube
Drain pan
6

INSTALLATION
SELECTING THE LOCATION
Place the unit in a flat locationwhere the air
outlets are not obstructed. Place the unit at
least 20” (50cm) away from a wall or other
obstacle.
MOUNTING THE EXHAUST HOSE
Slide the square end of the exhaust duct over
the hot air outlet on the back ofthe unit.
The exhaust hose should be kept as short and
straight as possible. Preventany sharp bends in
the exhaust hose, as this willtrap hot exhaust
air.
The hot exhaust air can be vented through the
wall or out a window. If mounting in the wall, the
height of the hole should be 16to 50 inches
(40cm to 130cm).
7

WINDOW KIT INSTALLATION
The window kit is designed to fitinto most
standard vertical and horizontal windows.
However, it may be necessaryto modify some
aspects of the installation process for certain
window types.
1. Open the window or slidingdoor and adjust
the length of the window kit to fit the
opening. Mark and cut down a single panel
of the window kit if necessary.
2. Place the window kit between the window
and the window frame as shown in the
images to the right. Close thewindow onto
the window kit to form a tightseal.
3. Attach the exhaust duct adapter to the
window kit. Tabs located on the adapter will
lock into place securing the adapter to the
window kit.
8

CONTROL PANELAND MULTI-COLOR DISPLAY
CONTROL PANEL
FAN SPEED
Button During the modes of cooling,heating and fanning, press this button to choose high, medium or low fan speed. In dehumidifying mode, this button is inoperable.
SWING Button Press this button to oscillate the vertical louvers or to stop oscillation.
∨Button This button decreases the room temperature/timer hours.
∧Button This button increases the room temperature/timer hours.
Power Button Press this button to turn the unit on or off.
MODE Button Press this button to select among the modes of auto, cooling, dehumidifying, fanning, or heating.
TIMER Button Press this button to turn the timer on/off.
MULTI-COLOR DISPLAY
A. Auto Mode
B. Cool Mode
C. Dehumidify Mode
D. Fan Mode
E. Heat Mode
F. Fan Speed (Low, High, Medium)
G. Temperature
H. Swing Mode
I. Sleep Mode
J. Clock and Timer
K. Timer On
L. Timer Off
M. Compressor is on
9

10
CONTROL PANEL FUNCTIONS
ON/OFF BUTTON
Starts or stops the unit.
MODE BUTTON
Press to select the operating mode:
Fan Mode
Air Conditioning Mode
Heating Mode
Dehumidifying Mode
Auto Mode
FAN BUTTON
Press to select the fan speed: High, Medium, and Low.
The fan speed can be visually distinguished by the number of the digital air segments (follow arrow
above) flow out from the windmill fan image on the multi-color display.
TEMPERATURE
When in cooling or heating mode, the desired temperature can be selected by pressing the ∧and ∨
buttons. The multi-color display flashes the temperature while it is being set. The multi-color display
shows the set temperature when it is not in temperature setting mode.
The multi-color display can show either Celsius or Fahrenheit. Press the ∧and ∨buttons
simultaneously to change the display from Celsius to Fahrenheit or vice versa.
TIMER
To set the auto start time, press the Timer on button until the multi-color display shows a flashing
“”. Press the ∧and ∨buttons to change the clock to the desired time for the unit to
automatically start. To set the auto stop time, press the Timer Off button and the multi-color display
will show a flashing “ ”. Press the ∧and ∨buttons to change the clock to the desired time
for the unit to automatically stop. The light will flash for 3 seconds to activate the timer you
programmed.
TIME DISPLAY
In the diagram above, the letter “J” points to the adjustable time display. To adjust the time, Press FAN,
SPEED and SWING together (at the same time), then press UP to adjust the hours, and press DOWN
to adjust the minutes.
SWING
To start horizontal oscillation, press the Swing button once. ‘ ’ icon will appear on the multi-color
display. To stop oscillation, press the Swing button again. Vertical air flow direction can be adjusted
manually.
OPERATION USING THE CONTROL PANEL
COOLING
1. Properly install the exhaust hoses.
2. Plug the power cord into a grounded outlet.
3. Turn on the unit by pressing the On/Off button on the control panel.
4. Press the Mode button until “ ” icon appears on the multi-color display.
5. Press the ∧or ∨buttons until the desired temperature appears on the multi-color
display. The temperature ranges from 61°F - 88°F (16°C - 31°C).
6. Select the fan speed by pressing the Fan button.
NOTE: During hot days, the unit will cool off the room most efficiently by setting the temperature at