Soleus Air PSR-06-01 User manual

V180131
3058080
Air conditioner must be upright for 24 hours prior to operating.
This ensures that the compressor will function as intended.

Thank you for choosing a Soleus Air Portable Air Conditioner. This Owner’s Manual will provide
you with valuable information necessary for the proper care and maintenance of your new product.
Please take a few moments to thoroughly read the instructions and familiarize yourself with all the
operational aspects of your new Soleus Air Portable Air Conditioner.
For your own records, please attach a copy of your sales receipt to this manual. Also, write the
store name/location, date purchased, and serial number below:
Store Name: ____________________________________________________
Location: _____________________________________________________
Date Purchased: _________________________________________________
Serial Number (located on back of unit): ______________________________
Before installing and using your portable air conditioner, please read this owner’s manual carefully. Store
this manual in a safe place for future reference.
1) Always place the unit on a level surface.
2) Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this
manual.
3) Maintain at least 10 inches (25 cm) clearance space around this unit. Do not block or cover air inlet or
outlet grilles.
4) The unit must be connected to a correctly grounded power supply.
5) Do not start or stop the unit by inserting or pulling out the power plug.
6) Do not use an adapter plug or extension cord.
7) Do not use the unit in the immediate surroundings of a bath, a shower or a swimming pool.
8) Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills unless instructed by this
manual.
9) Do not let children play near this unit.
10) Always inspect the cord for signs of damage before use. If the power cord is damaged, it must be replaced
by the manufacturer or a qualified service technician.
11) When cleaning the unit, always turn the unit off and unplug the power cord.
12) Do not mix old and new batteries in the remote control.
IMPORTANT INSTRUCTIONS
PURCHASE INFORMATION

Model Number PSR-06-01 PSR-08-01 PSR-10-01
Cooling Capacity 6,000 BTU/Hr 8,000 BTU/Hr 10,000 BTU/Hr
Dehumidification 76 pts/Day 101 pts/Day 116 pts/Day
Cooling Power
Usage
704 Watts
6.2 Amps
938 Watts
8.9 Amps
1172 Watts
10.2 Amps
Air Flow (High/Low) 205/164 CFM 205/164CFM 205/164 CFM
Power Source 115 V / 60 HZ 115 V / 60 HZ 115 V / 60 HZ
Noise Level dB(A) 53-55 dB 53-55 dB 53-55 dB
Product Weight 49.6 Lbs. 49.6 Lbs. 49.6 Lbs.
Operating
Temperature 61℉-88℉61℉-88℉61℉-88℉
Product Dimension
(W x H x D) 12.25”×29.87”
×13.25”
12.25”×29.87”
×13.25”
12.25”×29.87”
×13.25”
Refrigerant R-410A R-410A R-410A
Portable Air Conditioner (1)
Exhaust Hose (1)
Exhaust Hose Connector (1)
Window Kit Panel (3)
Window Kit Adapter (1)
Wing Nut (2)
Optional Drain Tube (1)
Drain Tube Stopper (1)
Remote Control (1)
AAA Battery (2)
Owner’s Manual (1)
Optional Window Security Pack (1)
PACKAGE CONTENTS
SPECIFICATIONS
• The cooling capacity is measured at an ambient temperature of DB 95˚F, WB 83 ˚F.
• Noise level is measured at a distance of 3.28 ft away from the front of the unit, when
the unit is in cooling mode.
• Power consumption is measured when the fan runs at the highest speed setting.
• These specifications are for reference only. For actual data, please refer to the rating
label on the back of the unit.
• If the environment temperature is higher than the max operating temperature or lower
than the minimum operating temperature, the air conditioner may not work properly.

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord
and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-
ble cord with no termination on the load side and a LCDI attachment plug on the line side.
The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the
nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.
The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the
risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they
must be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any
exposed metal.
The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:
1. Plug power cord into wall outlet, the LED light will turn on.
2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,
the LED light will turn off.
3. Press RESET button to restore power to the unit. Once power is restored, the LED light will turn
on again.
If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air
conditioner or attempt to reset the LCDI Plug. Contact Soleus N.A. Customer Service for troubleshooting
recommendations.
Note: Your unit’s power cord may
differ from the one shown.
WARNING:
1. DO NOT press the TEST button while the air conditioner is operating.
2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.
3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.
4. The cord and plug are intended for indoor use only.
RESET
TEST
POWER CORD AND PLUG

PRODUCT DIAGRAM
1. Control Panel
2. Manual Control Louver & Air Outlet
3. Carry Handle
4. Caster
5. Air Filter
6. Air Filter
7. Hot Air Discharge Opening
8. Air Intake Grille
9. Condensation Drain Hole
10. Exhaust Hose
11. Exhaust Hose Connector
12. Window Kit Adapter
13. Window Kit Panels
14. Wing Nuts
15. Optional Drain Tube
16. Drain Tube Stopper
17. Remote Control
18. Batteries
19. Optional Window Security Pack
MODEL# PSR-06-01/PSR-08-01/PSR-10-01

WINDOW VENTING KIT
OPTIONAL WINDOW SECURITY BRACKET
ASSEMBLY & INSTALLATION
When the unit is operating in air conditioning mode, the unit draws in indoor air and exhausts hot air out of the room
to complete the air exchange. The Window Kit must be installed when operating the unit in air conditioning, dehu-
midification. When the unit is operating in Fan Mode, no outdoor air exchange takes place. The window kit and ex-
haust hose do not need to be installed when the unit is used as a fan.
The supplied window kit can be installed in sliding windows and sliding glass doors up to 7 ft. long
(approximate length). When installed, be sure to keep the exhaust hose and short and straight as possible for
maximum efficiency.
PARTS & ASSEMBLY
Window Kit Adapter

.
WINDOW KIT ASSEMBLY

.
PORTABLE AIR CONDITIONER
The window venting kit must be installed in order for the unit to work correctly. The window venting kit has been de-
signed to fit into most vertical and horizontal window openings and sliding glass doors up to 7 feet..
1. Open the window or door to adjust the length of the Window
Kit Panels to fit the opening. If necessary, mark the kit and cut
one end down to properly fit the opening.
2. Twist the Exhaust Hose Connector over the discharge opening
on the back of the unit and extend the Exhaust Hose. (Keep the
exhaust hose as short and straight as possible)
3. Attach the Window Kit Adapter to the Exhaust Hose. Then attach
the Window Kit Adapter to the Window Kit panel. Close the window
or door tightly.
WINDOW KIT INSTALLATION
Keep the exhaust hose
as short and straight as
possible for maximum
efficiency.
Window Kit Adapter

Optional Security Bracket Installation
Your Window Kit also includes an optional security bracket that can be installed to prevent the window from being
opened from the outside while a Window Kit is installed.
SECURITY BRACKET
Single and Double Hung Windows
Sliding Windows

OPERATING INSTRUCTIONS FOR CONTROL PANEL BUTTONS
1) Power On and Off - Press the POWER button once to manually turn the unit on. Press the POWER
button once more to turn the unit off.
2) Mode Selection - Press the MODE Button repeatedly to cycle between the different modes: Air
Conditioner (Cool) mode, Fan-only mode, Dehumidifier (Dry) mode, Sleep mode, and Auto mode.
Each press of the MODE button will light up a different indicator on the control panel. The exhaust
hose and window kit must be installed when the unit is in Air Conditioner, Dehumidifier mode, Auto
mode, and Sleep mode. When using the unit as a fan, the window kit is not required.
3) Temperature - Select the desired temperature by pressing either the ▲ or ▼ button when using the
unit in Air Conditioner mode. The temperature indicator flashes to display the desired temperature set-
ting. After the temperature is set, the unit will display this temperature setting until it is changed by the
user. The temperature indicator display shows temperature in Fahrenheit. While the unit is plugged in,
but not powered on, press and hold the▲ and▼ buttons for 3 seconds to switch between Celsius and
Fahrenheit.
4) Fan Speed - Press FAN SPEED button to choose fan speed in High, Medium or low.
5) Timer - Press TIMER button to set the unit automatically turn ON or OFF. Use the ▲ and ▼buttons
to program the hour increment.
6) Turbo Cool - When Turbo Cool is activated, the unit will cool at 61°F on fan high for 10 minutes and
then return to the original settings.
7) Bucket Full - When the unit cannot evaporate the collected moisture fast enough, the excess water
will collect in a backup water tank located inside the unit. The BUCKET FULL indicator will light up.
8) Louver Direction - This unit has 2-way directional louvers. Use the louver guides manually to direct
air up and down.
Sleep Mode
Indicator
Fan Speed
Indicators
Auto Mode
Indicator
Air Conditioner
Mode Indicator
Fan Mode
Indicator
Bucket Full
Indicator
Turbo Cool
Indicator
Timer
Indicator
Dehumidifier Mode
Indicator
CONTROL PANEL
Power
Indicator