3
8
Bx8
Dx4
B
D
STEP 6-B Install the Cable Management Tray (3)
Way 2
The Installation of cable management
tray (3) are installed in the same way
as Way 1 in Step 6-A.
The cable management tray (3) should be
mounted on the middle connecting rod when
the frame is stretched more than 1720 mm.
The length of the supporting
beam should not exceed this
hole position.
F
0.16"x0.16"
Waste disposal This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmental safe recycling.
Common fault treatment
g
The following tips w ill help you detected and eliminate the c ommon fault
and error.If the fault you met is n ot lis ted below, p leas e c ontact with y our
s upplier. Only themanufacturer and profes s ionals a re c apable for inves tigatin
and correcting thos e fault and e rror.
1. Che ck i f all the c able s b e c onnected we ll
1. Che ck i f all the c able s b e c onnected we ll
2.Contact your s upplier or dealer
2.Contact your s upplier or dealer
1. Check if overloade d, max loading: 220 lbs;
1. Check if ove rloade d, max loading: 220 lbs;
1. Check if ove rloade d, max loading: 220 lbs;
2. Contact your s upplier or dealer
2. Contact your s upplier or dealer
2. Contact your s upplier or dealer
1. Contact your s upplier or deale r
1 .Repos itio n
2.Contact your s upplier or dealer
（Duty cycle: Max 2min on/1 8min OFF）
1. Res tart afte r s us pend for 1 8mins w hile
c onnecting with power;
2. Contact your s upplier or de aler;
1. P res s " M"and "3" together for 3 s e conds o r
more, a fter hearing continuous b e eping for twice,
it will res tore factory s ettings
2.Contact your s upplier or dealer
Go down but not go up
The motor not move as instructed
Rising In a low Speed
No response while pressing up
arrow/down arrow after connected
with a power supply
No response while long pressing up
arrow/down arrow after connected
with a power supply
Downward Sliding
Frequently Reposition
Overwork
Not enough up& down height
Method
Fault Phenomenon
ionAttent
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose
the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with each country's environmental legislation, not the
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when
playing, so any dangerous consequences caused by this improper action will not be on
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g.,
do not litter the tools around.Always be careful to treat the packaging materials in order
to avoid any possible danger , e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation.
°C
