SOLTEK SL-65DRV User manual

R
The Soul Of Computer Technology
SL-65DRV USER MANUAL v1.2

his User’s Guide & Technical Reference is to help system manu-
facturers and end-users set up and install the mainboard.
Every effort has been made to ensure that the information in this
manual is accurate. Soltek omputer Inc. is not responsible for print-
ing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on the
part of Soltek omputer Inc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek omputer Inc.
ompanies and products mentioned in this manual are for identifi-
cation purpose only. Product names appearing in this manual may
or may not be registered trademarks or copyrights of their respec-
tive companies.
Soltek omputer inc. Provides this manual “As is “ without warranty
of any kind, either express or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for
a particular purpose. In no event shall Soltek computer inc. be li-
able for any loss or profits, loss of business, loss of use or data,
interruption of business, or for indirect, special, incidental, or con-
sequential damages of any kind, even if Soltek computer inc. has
been advised of the possibility of such damages arising from any
defect or error in this manual or product.
Copyright © 2001 Solte Computer Inc. All Rights Reserved.
NOTICE Product Model : SL-65DRV
Manual Revision : V1.2
Release Date : July 2001
T
• Intel, eleron, Pentium II, Pentium III are trademarks of Intel orporation.
• Intel 82815 Graphic Memory ontroller Hub(GM H), 82801 I/O ontroller Hub(I H) are trade-
marks of Intel orporation.

SOLTEK AROUND THE WORLD
SOLTEK COMPUTER INC.
Address : 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi- hih, Taipei-
Hsien, Taiwan, R.O. .
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soltek.com.tw
SOUL TECHNOLOGY EUROPE B.V.
Address : Hongkongstraat 55, 3047 BP Rotterdam. The Neth-
erlands
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soultech-europe.com

65DRV
CONTENT
CHAPTER 1 INTRODUCTION ................................................. 8
1-1 MAINBOARD SPE IFI ATION ................................................. 9
1-1.1 PRO ESSOR ................................................................................... 9
1-1.2 HIPSET ........................................................................................... 9
1-1.3 AWARD BIOS V6.0 ........................................................................... 9
1-1.4 SOUND ONTROLLER .................................................................... 9
1-1.5 FULL FEATURED A ELERATED GRAPHI S PORTS (AGP)
ONTROLLER .................................................................................. 9
1-1.6 ADVAN ED HIGH PERFORMAN E SDR/DDR DRAM
ONTROLLER ................................................................................. 9
1-1.7 POWER MANAGEMENT ................................................................ 10
1-1.8 MULTI-I/O FUN TION .................................................................... 10
1-1.9 EXPANSION SLOTS ....................................................................... 10
1-1.10 FORM FA TOR ............................................................................ 10
1-1.11 HARDWARE MONITOR ................................................................ 11
1-2 MAINBOARD LAYOUT --- 65DRV ........................................... 12
1-3 HIPSET DIAGRAM--- 65DRV ............................................... 13
CHAPTER 2 HARDWARE SETUP......................................... 15
2-1 PU INSTALLATION ............................................................... 16
2-2 MEMORY INSTALLATION ....................................................... 17
2-3 A ELERATED GRAPHI S PORT(AGP) PRO INSTALLATION ... 19
2-4 HDD/FDD INSTALLATION....................................................... 20
2-5 FSB Frequency SELE T (By SW1 DIP1~DIP4) ................................ 22
2-6 JUMPER SETTING FOR DEVI ES ON BOARD .................... 23
2-6.1 JP3/JP4 AGP Voltage Select .......................................................... 23
2-6.2 JDIMM1/JDIMM2 Memory Module Voltage Select .......................... 24

Introduction
5
2-6.3 JBAT1 For lear MOS DATA ........................................................ 25
2-7 ONNE TORS ONFIGURATIONS ...................................... 26
2-7.1 FAN1, FAN2, FAN3 On board FAN onnector ................................ 26
2-7.2 WOL1 Wake-On-LAN onnector .................................................... 27
2-7.3 J D_IN1 D-ROM Audio onnector .............................................. 28
2-7.4 RT2 Thermal Sensor onnector ..................................................... 29
2-7.5 omplex Header ON1 ................................................................. 30
2-7.6 ATX Power Supply onnector ........................................................ 32
2-7.7 hassis Panel onnectors ............................................................. 33
2-7.8 S R1 Smart ard Reader onnector ............................................. 34
2-7.9 NR ommunication And Networking Riser Slot ............................ 35
2-7.10 USB Header (USB2 & USB3 Header) ........................................... 36
2-7.11 PS/2 Mouse And PS/2 Keyboard .................................................. 36
CHAPTER 3 SOFTWARE SETUP ......................................... 38
3-1 VIA HIPSET DRIVER INSTALLATION (4-IN-1 DRIVER) ...... 39
3-2 HARDWARE MONITOR INSTALLATION ................................ 42
3-3 A ’97 AUDIO ODE DRIVER INSTALLATION .................... 44
CHAPTER 4 BIOS SETUP ..................................................... 46
4-1 WHAT IS BIOS SETUP............................................................ 47
4-2 HOW TO RUN BIOS SETUP ................................................... 47
4-3 WHAT IS MOS ...................................................................... 47
4-4 WHAT IS POST ....................................................................... 47
4-5 BIOS UPGRADE ..................................................................... 47
4-5.1 BEFORE UPGRADING BIOS ......................................................... 48
4-5.2 UPGRADE PRO ESS .................................................................... 48
4-6 BIOS SETUP --- MOS SETUP UTILITY................................ 52

65DRV
6
4-6.1 MOS SETUP UTILITY .................................................................. 52
4-6.2 STANDARD MOS SETUP ............................................................ 53
4-6.3 ADVAN ED BIOS FEATURES ....................................................... 56
4-6.4 ADVAN ED HIPSET FEATURES ................................................ 60
4-6.5 INTEGRATED PERIPHERALS ....................................................... 66
4-6.6 POWER MANAGEMENT SETUP ................................................... 72
4-6.7 PNP / P I ONFIGURATION ......................................................... 78
4-6.8 P HEALTH STATUS ...................................................................... 81
4-6.9 FREQUEN Y/VOLTAGE ONTROL .............................................. 83
4-6.10 LOAD OPTIMIZED DEFAULTS..................................................... 85
4-6.11 SET SUPERVISOR / USER PASSWORD .................................... 85
4-6.12 SAVE & EXIT SETUP .................................................................... 86
4-6.13 EXIT WITHOUT SAVING .............................................................. 86
APPENDICES ......................................................................... 88
APPENDIX-1 TE HNI AL TERMS INTRODU TION ................. 89
APPENDIX-2 IDENTIFYING BIOS VERSION AND BIOS PART
NUMBER ............................................................... 90
APPENDIX-3 IDENTIFYING MAINBOARD MODEL NUMBER .... 92

Introduction
7
Mainboard
====Support D
====User’s Manual
====Bundled Bonus Pack D
====Bundled Bonus Pack Manual
====Temperature Sensor able
====ATA66/100 IDE able
====RS232 able
FDD able
ITEM LIST CHECKUP

65DRV
8
CHAPTER 1
INTRODUCTION
• This chapter briefly introduces this characteristics of the mainboard. It
includes the information regarding the chipset, PU types, built-in
functions and layout. Users will have more ideas about mainboards after
reading this chapter.
This chapter contains the following topics :
1-1 MAINBOARD SPECIFICATION
1-2 MAINBOARD LAYOUT
1-3 CHIPSET DIAGRAM

Introduction
9
1-1 MAINBOARD SPECIFICATION
1-1.1 PROCESSOR
• Supporting Intel® F -PGA Pentium IIITM up to 1GHz.
• Supporting Intel® F -PGA 370 eleron & PGA 370 eleron up to 850MHz.
• Supporting VIA yrix III up to 800MHz or above.
• Supporting PU voltage Auto-Detect circuit.
1-1.2 CHIPSET
• Apollo Pro266 hipset:
VT8633 V-Link Host system controller and VT8233 V-Link to P I/LP bridge.
• IT 8705F simple LP I/O.
1-1.3 AWARD BIOS V6.0
• Plug & Play V1.0.
• Flash Memory for easy upgrade.
• BIOS writing protection.
• Year 2000 compliant.
• SmartDO Anti-Burn shield.
• Redstrom Overclocking Tech.
1-1.4 SOUND CONTROLLER
• Sound Blaster Pro Hardware and Direct Sound Ready A ’97 Digital Audio
ontroller with odec ON BOARD.
1-1.5 FULL FEATURED ACCELERATED GRAPHICS PORTS
(AGP) CONTROLLER
• Synchronous and pseudo-synchronous with the host PU bus with optimal
skew control P I AGP PU Mode 33/66/100 MHz DDR 3x synchronous.
• Supporting 66MHz 1x/2x/4x modes for AD and SBA signaling.
• AGP v2.0 compliant.
1-1.6 ADVANCED HIGH PERFORMANCE SDR/DDR DRAM
CONTROLLER
• Supporting memory size up to 3GB.
• Supporting 184-pin DDR DRAM type only.

65DRV
10
1-1.7 POWER MANAGEMENT
• A PI 1.0 compliant (Advanced onfiguration and Power Interface).
• APM V1.2 compliant (Legacy power management).
• System event monitoring with two event classes.
• Supporting PS/2 Keyboard & Mouse power on.
• Supporting Wake On LAN (WOL) & Wake On Modem.
• Supporting real time clock (RT ) with date alarm, month alarm, and
century field.
• Supporting Keyboard power on & Mouse Power on.
1-1.8 MULTI-I/O FUNCTION
• Two Ultra DMA-33 / 66 /100 Master Mode P I EIDE ports.
• Two UART’s for omplete Serial Ports.
• One dedicated IR connector:
-- At third serial port dedicated to IR function either through the two complete serial
ports or the third dedicated port Infrared-IrDA (HPSIR) and ASK (Amplitude Shift
Keyed) IR.
• Multi-mode parallel connector supporting:
-- Standard mode, E P and EPP.
• Floppy Disk connector supporting:
Two FDDs with drive swap support .
• Universal Serial Bus connector supporting:
--- USB v1.1 and Intel Universal H I v1.1 compatible.
--- 2 built-in USB connectors, in addition to one internal USB header which
requires a USB cable to support 2 more optional USB ports.
• PS/2 Keyboard connector.
• PS/2 Mouse connector.
1-1.9 EXPANSION SLOTS
• Six P I bus Master slots.
• One NR slot.
• One AGP 4x Pro mode slot.
• Three DIMM slots.
1-1.10 FORM FACTOR
• ATX from factor, 4 layers P B.
• Mainboard size 22.0cm X 30.2cm.

Introduction
11
1-1.11 HARDWARE MONITOR
• Programmable control, status, to provide monitoring and alarm for flexible
desktop management (software include).
• 5 positive voltage statuses monitoring.
• 2 temperatures statuses monitoring.
• 1 Fan-speed status monitoring.

65DRV
12
1-2 MAINBOARD LAYOUT --- 65DRV
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
PCI 6
AGP PRO 4X
VIA
VT8633
VIA
VT8233
Li
Battery
AC'97
Codec
LPC I/O
Controller
FLASH BIOS
SPK RST PWR/LED T/LED
HDD/LED IR PWR SMI
CON1
++
--
+-
1
30
SCR1
114
SW1
ON DIP
1 2 3 4
SOCKET 370
RT1
LPT1
COM2 COM1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
PS/2 MOUSE
PS/2 K/B
upper
lower
USB1 USB0
upper
lower
IDE1
IDE2
FDC
ATX POWER
Cloc
Generator
FAN2
1 3
FAN3
3 1
CNR 1
1 3 1 3
JP3 JP4
1 3
JBAT1
14
JCD_IN1
WOL1
RT2
FAN1
1 3
1 3
1 3
JDIMM1
JDIMM2
USB2
1
16
USB3
1
16
LED1
Using non-compliant memory with higher bus clock (over clocking)
may severely compromise the integrity of system.

Introduction
13
VIA
VT8633
VIA
VT8233
Keyboard
& Mouse
ATA 33/66/100
PM Control,
GPIO, Reset
Main
Memory
(DDR DRAM)
3D Graphics
Controller
BIOS
ROM
USBx6
LPC lO
Serial Port x 2
Infrared Port x 1
Parallel Port x 1
FDD x1
Soc et 370
CPU
PCI3 PCI5 PCI4 PCI1 PCI2 PCI6
AGP PRO Slot
AC'97 Codec
Hardware Monitoring
1-3 CHIPSET DIAGRAM--- 65DRV
Diagram of VIA VT8633 System Block Using the VT8233 South
Bridge

65DRV
1
MEMO
MEM
O

15
Hardware Setup
CHAPTER 2
HARDWARE SETUP
2-1 CPU INSTALLATION
2-2 MEMORY INSTALLATION
2-3 AGP PRO INSTALLATION
2-4 HDD/FDD INSTALLATION
2-5 BUS CLOCK SELECT
2-6 JUMPER SETTING FOR DEVICES ON BOARD
2-7 CONNECTORS CONFIGURATION
ATTENTION !!!
1. Please refer to your processor installation or other
documentation attached with your CPU for more de-
tailed installing instruction.
2. Installing a heat sin and cooling fan is necessary for
proper heat dissipation from your CPU. Incorrect in-
stallation may result in overheating and damage of
your CPU.
3. Before changing the setting of CPU Vcore from BIOS
program, user SHOULD ma e sure of correct specifi-
cation both of CPU CLOCK and RATIO. Incorrect set-
ting may cause damage to your CPU.
This chapter contains the following topics :

16
65DRV
WARNING !!!
• Make sure that +5V DCV and +3.3 DCV of your power supply are suitable
for the processor.
• Any attempt to operate the III or Celeron processor without a suitable
cooling Fan will damage processor and other component.
2-1 CPU INSTALLATION
Take notice of the red circles
as shown below. While insert-
ing the PU into the socket,
you can find out there is a
definite pin orientation for
PU and socket.
2
SOCKET 370
Make sure that the PU is
placed into the socket tightly.
Then lower down the lever to
complete the PU installation.
3
SOCKET 370
Pull out the lever from the socket,
and then raise the lever up to a
90-degree angle.
1
SOCKET 370

17
Hardware Setup
Installing DIMM
• Make sure you have the correct memory module type for your mainboard.
• Insert the module(s) as shown below, DIMMs have 184-pins and one notch
that will be matched by the ON BOARD DIMM socket. Memory modules are
installed by inserting them straight into the slot until they “click” in the right
place. They only fit in one direction, so do not force them in by a wrong
direction.
184-Pin DIMM Notch Key Definitions(2.5V)
DRAM Key Position Voltage Key Position
2.5V
2-2 MEMORY INSTALLATION
Removing DIMM
• Press down the holding clips on both sides of a DIMM socket and the
module will be released from it.
WARNING!!!
• Make sure to unplug your power supply before adding or removing memory
modules or other system components. Failure to do so may cause severe
damage to both your mainboard and expansion cards.
• Be careful when inserting or removing DIMM. Forcing a DIMM in or
out of a socket improperly may damage the memory module or the socket.
Some DIMMs which contain EDO or FT DRAM are incompliant with
the mainboard. The M/B supports 2.5V true SDRAM DIMMs only.

18
65DRV
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
PCI 6
AGP PRO 4X
VIA
VT8633
VIA
VT8233
Li
Battery
AC'97
Codec
LPC I/O
Controller
FLASH BIOS
SPK RST PWR/LED T/LED
HDD/LED IR PWR SMI
CON1
++
--
+-
1
30
SCR1
114
SW1
ON DIP
1 2 3 4
SOCKET 370
RT1
LPT1
COM2 COM1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
PS/2 MOUSE
PS/2 K/B
upper
lower
USB1 USB0
upper
lower
IDE1
IDE2
FDC
ATX POWER
Cloc
Generator
FAN2
1 3
FAN3
3 1
CNR 1
1 3 1 3
JP3 JP4
1 3
JBAT1
14
JCD_IN1
WOL1
RT2
FAN1
1 3
1 3
1 3
JDIMM1
JDIMM2
USB2
1
16
USB3
1
16
LED1
NOTICE : When LED
“LED1” is on, meaning that
2.5V is on DIMM slots,
please do not add or remove
memory modules .

19
Hardware Setup
2-3 ACCELERATED GRAPHICS PORT(AGP) PRO INSTALLATION
• The AGP Pro connector is an extension of the existing AGP connector
and it is compatible with existing AGP cards.
Accelerated Graphics Port (AGP) Pro Slot
Rib(inside slot)
20-pin bay Rib(inside slot) 28-pin bay
AGP Accelerator
AGP Pro slot
blockader
CAUTION!!
The AG ro slot comes with a warning label over the 20-pin bay. Do not
remove this label and the safety tab underneath if you use an AG card
without a retention notch. Without the labels, AG cards may be placed
into the wrong place. If that’s the case, this action will damage your card,
slot, and mainboard. Remove the label ONLY if you will be using an AG
ro card.

20
65DRV
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
PCI 6
AGP PRO 4X
VIA
VT8633
VIA
VT8233
Li
Battery
AC'97
Codec
LPC I/O
Controller
FLASH BIOS
SPK RST PWR/LED T/LED
HDD/LED IR PWR SMI
CON1
++
--
+-
1
30
SCR1
114
SW1
ON DIP
1 2 3 4
SOCKET 370
RT1
LPT1
COM2 COM1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
PS/2 MOUSE
PS/2 K/B
upper
lower
USB1 USB0
upper
lower
IDE1
IDE2
FDC
ATX POWER
Cloc
Generator
FAN2
1 3
FAN3
3 1
CNR 1
1 3 1 3 JP3
JP4
1 3
JBAT1
14
JCD_IN1
WOL1
RT2
FAN1
1 3
1 3
1 3
JDIMM1
JDIMM2
USB2
1
16
USB3
1
16
LED1
• To install HDD (Hard Disk Drive), you may connect the cable’s blue con-
nector to the mainboard’s primary (IDE1) or secondary (IDE2) connector,
and then connect the gray connector to your slave device and the black
connector to your master device. If you install two hard disks, you must
configure the second drive to Slave mode by setting its jumper accordingly.
Please refer to your hard disk documentation for the jumper settings.
Hard Disk Drive onnector:
Orient the red line on the
IDE ribbon cable to Pin1.
2-4 HDD/FDD INSTALLATION
Black
connector
Gray connector
Blue connector
IDE Cable
red line