Solvit HoundAbout Technical specifications

080312
HoundAbout ™Pet Stroller
Care & Use Guide
Thank you for your purchase of the Solvit Products HoundAbout™ Pet Stroller. The stroller assembles in about
20-30 minutes, using a Phillips screwdriver and an adjustable wrench (or 9mm and 10mm sizes).
Assembly: The package contains: one partially assembled main cabin; two large wheels, one smaller (front) wheel;
one front wheel fork assembly; one handlebar; one handlebar mounting tube kit; one cup holder kit; one parking
brake kit; one adjustable leash; and one cushion. If any parts are missing, contact Solvit for prompt replacement.
Step 1: Attach large wheels to cabin: Insert the spindle of each large wheel into either side of the axle. When
inserted, the spring lock mechanism on the underside of the axle will make an audible “click”. Pull firmly to make
sure wheel is properly installed. To remove, depress the spring lock mechanism and withdraw the wheel.
Step 2: Attach the front wheel assembly: Assemble the smaller wheel to the front fork and check for
alignment. Slide the short square tube on the front wheel assembly over the m
tube at the
the “quick release” pin and tighten fully.
atching
lower front edge of the stroller cabin. Align the holes in each tube, install
ep 3: The sides of the cabin are held in place by means of a roof support rod and de
tar
e
ck
ther.
St
two black plastic “star knobs”. With the wheels resting on the ground, rotate one si
panel into a vertical orientation. Position the support rod inside the trailer so one s
knob can be inserted through the grommet and frame on the side of the trailer and
into the threads on the end of the support rod. Repeat with the other star knob on th
other side of the trailer, and fully tighten both star knobs.
Step 4: Install the parking brake. This is attached on the lower left side of the
cabin, in front of the wheel. Insert two screws through the brake assembly, bla
rubber washers , the holes in the cabin fabric and finally through the steel frame,
extending into the interior of the cabin. Install the washers and 9mm nuts to the
screws and tighten. The parking brake is engaged by moving the brake lever to
the forward position. Hint: if the brake seems difficult to operate, loosen the
mounting screws one-quarter turn and test again.
(The steps that follow are made easier by engaging the parking brake now.)
Step 5: Install the cushion: The four hook-and-loop straps on the cushion
should “loop” around the interior frame tubes and “hook” back onto each o
When installed correctly, the cushion should cover all tubing.
Step 6: Attach the handlebar: The two 4-inch handlebar mounting tubes
attach to the frame on the rear panel. With the open end of the mounting tube
facing up, align the holes on the tube to the holes on the frame. Insert screws
through the tube and frame and attach 10mm nuts from the inside of the cabin.
Tighten using a screwdriver and wrench. Slide the ends of the handlebars into
the mounting tubes, align the holes, and insert the lock pins with the head of
the lock pins facing forward. Secure the wire hoop on each lock pin.
Step 7: Install the cup holder: The large clamp fits over the cushioned section of the handlebar; the small clamp fits
over the non-cushioned section. Position the appropriate clamp and attach the cup holder with the nut and screw.
Adjust tightness so the cup holder does not “tilt” while in use.

Loading and unloading pets: Load and unload pets only through the rear door, with the front door closed. With
the pet inside the stroller, attach one end of the safety leash to the pet’s collar and the other end to one of the D-
rings located inside the stroller. Adjust the length of the leash so the pet cannot exit through the front window
when it is open. Always close the rear door before strolling or jogging. To reach inside the cabin while strolling,
we suggest using the zippered, sunroof window.
Additional Features: While loading your dog or accessing the interior of the cabin, the rear door can be kept in
the open position by connecting the hook tape strip on the inside bottom of the door to the loop tape strip located on
the sunroof, above the rear pocket. Always keep this door closed while riding.
The front of the stroller includes a vinyl windscreen door and a breathable mesh door. The stroller can be used with
one, both or none of these doors open. To open the vinyl door only, roll the door into a tube shape so the loop-tape
on the inside of the door connects to the hook-tape on the top of the cabin. To ride with both doors open, roll them
up together into a tube shape and connect the hook-and-loop-tapes. Make sure the safety leash is adjusted so the
pet cannot exit through the front door opening. There is also a sun roof at the top of the cabin. It can be held in the
open position by unzipping it, rolling it forward and securing it with the hook-and-loop tape
Locking/unlocking front wheel: For best maneuverability and convenience,
leave the front wheel in the swiveling mode, even while jogging. The front
wheel can be locked into either of two positions (“full forward” or “full
rearward”) by pulling up and rotating the lock knob at the top of the wheel
assembly. The knob is in the “locked” position when the molded ribs are facing
forward. To return to swiveling mode, pull the lock knob up and rotate 180
degrees so the molded ribs face rearward.
The stroller is equipped with a general storage pocket on the left side, an
insulated bottle pocket on the right side, a specialized pocket on the upper rear
panel for holding sunglasses, cell phone, MP3 player, etc., and a hidden security
pocket under the rear panel. The security pocket has two zipper pulls and can be
locked with a small pad lock (not included).
As an added convenience, the stroller includes an external leash point on the lower back frame. Only use this leash
point when the stroller is safely parked with the brake engaged.
Cleaning: The cabin fabric and windscreen can be cleaned with a damp cloth or sponge. The interior cushion is
washable in a commercial top loading machine. Use mild detergent, cold water, and line dry.
Safety Guidelines:
•The stroller is intended to carry pets only. No human passengers!
•To prevent accidental rollaways, apply the parking brake anytime the stroller is unattended.
•Always travel with the rear door closed. When moving, your dog should always be secured with the safety
leash adjusted to the correct length.
•Do not exceed the recommended weight capacity. Check tire inflation before every ride.
Warranty: The HoundAbout Stroller is warranted to be free from defects in materials or workmanship for the
lifetime of the product. This warranty does not apply to normal wear or damage from misuse, abuse,
neglect, or accident. This warranty is not transferable. Please retain your original sales receipt. For
warranty service, contact Solvit at wa[email protected], or 866-676-5848.
SOLVIT Products, LP 6720 Exchange Drive Mansfield, TX 76063
Tel: 866-6-SOLVIT (866-676-5848) Fax: [phone]
Email: [e-mail] www.solvitproducts.com