Sonoff ZBMINI-L User manual

User manual V1.0
ZBMINI-L
Smart Switch
(No Neutral Required)
· 中 文 --------- --1-6 · English---------- 7-12 · FCC Warning--------13

中⽂
产品介绍
按键
设备重量＜1Kg，建议安装⾼度＜2⽶。
Zigbee信号指⽰灯（绿⾊）
开关指⽰灯(红⾊)
功能特点
SONOFF单⽕智能开关(Zigbee版)基于Zigbee3.0⽆线通讯协议，通过连接Zigbee⽹关
实现远程控制、设置定时开/关、设备智能场景联动等功能。
以上功能特点取决于Zigbee⽹关的功能。
远程控制 智能定时/延时 语⾳控制 分享功能
智能场景 上电状态
外接开关 添加摄像头
Shenzhen Sonoff Technologies Co., Ltd.
1
指⽰灯状态说明
指⽰灯状态 状态说明
绿灯慢闪 配对模式
绿灯常亮 ⽹络连接正常
绿灯快闪
红⾊亮/灭 设备开/关
绿灯慢闪
⽹络连接异常
ZBMINI-L和路由设备连接正常，路由设备和⽹关断连
⽹络连接异常
⾮配⽹状态下慢闪：ZBMINI-L󱘘󵗟设备断连

中⽂
断电
设备安装、故障维修请由专业资质电⼯操作。切勿在设备通电时进⾏接线操作或触碰到接线
端⼦，以免发⽣触电危险！
接线
Shenzhen Sonoff Technologies Co., Ltd.
2
L In
S2S1
100-240V AC
N
L Out
L In
S2
100-240V AC
N
L Out
ON O FF
ON O FF
ON O FF
ON O FF
L In
S2
100-240V AC
N
L Out S1
L In
S2
100-240V AC
N
L Out
以上③④接线⽅式请确保设备Lin󶔎供电输⼊正常，否则会导致设备⼯作异常。
① ②
③ ④

确保线路接入无误。
外接的开关类型⽀持翘板和⾃回弹开关，出⼚默认为⽀持翘板开关类型。
开关类型切换⽅法：短按按键三次，设备红灯快闪3下提⽰，此时开关类型切换成功。
中⽂
Shenzhen Sonoff Technologies Co., Ltd.
3
使⽤说明
1.下载“易微联”App
eWeLink
Android™&iOS
2.󴷱󱶨SONOFFZigbee󶶘关
3.上电
配对⾄易微联App
通电后，设备⾸次使⽤，默认进⼊配对模式，Zigbee信号指⽰灯呈“ 慢闪”状态。
三分钟内没配对成功，设备将退出配对模式，如需再次进⼊，⻓按设备按键5秒直到Zigbee
信号指⽰灯呈“慢闪”状态即可。

中⽂
4
Shenzhen Sonoff Technologies Co., Ltd.
4.将ZBMINI-L添加⾄⽹关
ZB B ridge
已添加设 备:0
暂无子 设备，请添 加
添加
打开eWeLinkApp，选择要连接的⽹关，点击󾖶添加󾖶⼦设备，等待搜索添加设备。
添加设备
正在连接
请让设 备尽量 靠近网 关
135s
找到设备
1个设备 已找到
>
配对⾄亚⻢逊⾳箱
1.下载最新版AmazonAlexaApp,并配对带Zigbee⽹关的亚⻢逊⾳箱。
2.给ZBMINI-L上电，设备默认进⼊配对模式，Zigbee信号指⽰灯呈“慢闪”状态。
3.对亚⻢逊⾳箱说"Alexa,discovermydevices",即可⾃动发现设备。
三分钟内没配对成功，设备将退出配对模式，如需再次进⼊，⻓按设备按键5秒直到Zigbee
信号指⽰灯呈“慢闪”状态即可。
如添加失败，请将设备移近⽹关后再重新添加。
如添加失败，请将设备移近⽹关后再重新添加。

中⽂
Shenzhen Sonoff Technologies Co., Ltd.
1.参照⽹关使⽤说明书下载App和连接⽹关。
2.让设备进⼊到配对模式.
3.根据⽹关对应的APP提⽰添加设备，添加过程中选择eWeLink或SONOFF品牌。
如添加失败，请将设备移近⽹关后再重新添加。
添加说明：
其它App应⽤平台及⽹关推荐
本设备除⽀持SONOFFZigbee󶶘关外，还⽀持⽹关：Samsung SmartThings hub
SmartThings
5
产品参数
产品型号
输⼊
输出
⽆线连接
⼯作温度
外壳材料
产品规格
ZBMINI-L
100-240VAC50/60Hz6AMax
Zigbee3.0
-10~40℃
PCV0
100-240VAC50/60Hz6AMax
最⼤负载
54x45x24mm
本设备不⽀持其它类型的感性负载如⻛扇等。
认证 TUV/CE/FCC/UKCA/RoHS
通讯距离 最⼤50⽶（空旷环境）
阻性负载：
1380W Max @230V, 720W Max @120V
LED灯：
300W Max @230V, 150W Max @120V

中⽂
6
Shenzhen Sonoff Technologies Co., Ltd.
恢复出⼚设置
1.按外接开关10下，设备会⾃动开关3次表⽰设置成功。
2.⻓按设备按键5秒。
3.在eWeLinkApp端删除⼦设备。
可通过以下任意⽅法让设备恢复出⼚设置（恢复出⼚设置后设备⾃动进⼊配对模式）:
⽀持的语⾳平台

SONOFF Zigbee 3.0 Smart Switch (No Neutral Required) allows you to remote control,
schedule on/off and set smart scenes to trigger other devices, etc. by connecting
Zigbee hub.
Remote Control Single/Countdown
Timing
Voice Control Share Control
Smart Scene Power on State
External Switch Camera Linking
Shenzhen Sonoff Technologies Co., Ltd.
7
Green LED indicator slow flashes
Green LED indicator keeps on
Green LED indicator quick flashes
Red LED indicator on/off Device on/off
Green LED indicator slow flashes
Abnormal network connection
ZBMINI-L and router connect normally, but router and the
hub are disconnected
Abnormal network connection
Slow flashing under non-pairing state: ZBMINI-L and the
parent device are disconnected
Product introduction
The device weight is less than 1 kg. The installation height of less than 2 m is
recommended.
Button
LED signal indicator(Green)
On/Off LED indicator(red)
LED indicator status instruction
LED indicator status Status instruction
Pairing mode
Device is on line
Features
English
Above functions are determined by the connected ZigBee Hub.

L In
S2S1
100-240V AC
N
L Out
L In
S2
100-240V AC
N
L Out
L In
S2
100-240V AC
N
L Out S1
L In
S2
100-240V AC
N
L Out
For the above ③④ wiring methods, please ensure the proper wiring and powering
of the L in terminal, otherwise it will cause the device to work abnormally.
① ②
③ ④
Shenzhen Sonoff Technologies Co., Ltd. English
Power off
Wiring instruction
Please install and maintain the device by a professional electrician. To avoid electric
shock hazard, do not operate any connection or contact the terminal connector
while the device is powered on!
ON O FF
ON O FF
ON O FF
ON O FF
8

The device will exit the pairing mode if it doesn't be paired within 3mins. If you
want to enter again, long-press the button of the device for 5s until the Zigbee
signal indicator “slow flashes” then release.
Shenzhen Sonoff Technologies Co., Ltd. English
Supported switches are rocker switch and push button and factory default by
supporting rocker switch.
Method of change the switch type: Short-press the button 3 times, then the red
LED indicator will quick flash 3 times to indicate that the switch mode is changed
successfully.
Make sure all wires are connected correctly.
Operating instruction
Pair with eWeLink App
1. Download the eWeLink App
2. Pair SONOFF ZB Bridge to your eWeLink account
3. Power on
After powering on, the device will enter the pairing mode defaulted during the first
use and the Zigbee LED signal indicator will “flash slowly”.
eWeLink
eWeLink
Android™ & iOS
9