Sony SLV-ED8KR User manual

MICROFILM
SERVICE MANUAL
Korean Model
SLV-ED8KR/ED9KR
RMT-V244/V246
SPECIFICATIONS
G
• Refer to the SERVICE MANUAL of VHS MECHANICAL
ADJUSTMENTS VI for MECHANICAL ADJUSTMENTS.
(9-921-647-11)
* The abbreviations of ED8 and ED9 contained in this service manual are indi-
cated when these models are common to all their corresponding models as
given below.
Photo: SLV-ED8KR S MECHANISM
ED8KR
ED8
Abbreviated
model name
All model
names
SLV- ED9KR
ED9
VIDEO CASSETTE RECORDER
– Continued on next page –

– 2 –
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-sol-
dered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transis-
tors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recom-
mend their replacement.
5. Check the B+ voltage to see it is at the values specified.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK !OR DOTTED
LINE WITH MARK !ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.

– 3 –
TABLE OF CONTENTS
Section Title Page Section Title Page
SERVICE NOTE ...................................................................... 4
1. GENERAL
Getting Started .............................................................. 1-1
Basic Operations ........................................................... 1-5
Additional Operations.................................................... 1-8
Editing............................................................................ 1-11
Additional Information ................................................... 1-12
2. DISASSEMBLY
2-1. Upper Case Removal.................................................... 2-1
2-2. RJ-79, NK-11 Board Removal....................................... 2-1
2-3. Rear Panel Removal ..................................................... 2-1
2-4. Front Panel Section Removal ....................................... 2-1
2-5. FR-137, DM-77, SW-307, IO-64 Board
Removal (ED9).............................................................. 2-2
2-6. Control Switch Block Removal (ED9) ........................... 2-2
2-7. FR-137, DM-77, IO-64 Board Removal (ED8) ............. 2-2
2-8. Mechanism Deck Removal ........................................... 2-2
2-9. Power Block Removal ................................................... 2-3
2-10. PS-414, MA-325 board Removal .................................. 2-3
2-11. Internal Views ................................................................ 2-4
2-12. Circuit Boards Location ................................................. 2-5
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram .................................................. 3-1
3-2. Video1 Block Diagram................................................... 3-4
3-3. Video2 Block Diagram................................................... 3-5
3-4. Servo/System control Block Diagram ........................... 3-7
3-5. Audio Block Diagram..................................................... 3-9
3-6. Tuner Block Diagram..................................................... 3-11
3-7. Mode Control Block Diagram ........................................ 3-13
3-8. Power Block Diagram.................................................... 3-15
4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagram ........................................... 4-3
4-2. Printed Wiring Boards and Schematic Diagrams ......... 4-5
MA-325 (Head Amp) Schematic Diagram .................... 4-5
MA-325 Printed Wiring Board ....................................... 4-9
MA-325 (Video, Audio) Schematic Diagram ................. 4-11
MA-325 (System Control) Schematic Diagram ............ 4-15
MA-325 (Servo Control) Schematic Diagram ............... 4-17
MA-325 (Bias, CTL) Schematic Diagram ..................... 4-19
MA-325 (Hi-Fi Audio) Schematic Diagram.................... 4-21
MA-325 (OSD) Schematic Diagram.............................. 4-23
MA-325 (IO) , RJ-79 Schematic Diagrams and
RJ-79 Printed Wiring Board .......................................... 4-25
MA-325 (Tuner) Schematic Diagram ............................ 4-27
NK-11 Printed Wiring Board and
Schematic Diagram ....................................................... 4-29
DM-77, IO-64 Printed Wiring Boards and
Schematic Diagrams ..................................................... 4-31
FR-137, SW-307 Printed Wiring Boards....................... 4-33
FR-137, SW-307 Schematic Diagram .......................... 4-35
PS-414 Printed Wiring Board........................................ 4-37
PS-414 Schematic Diagram.......................................... 4-39
SR-718 Printed Wiring Board ....................................... 4-41
SR-718 Schematic Diagram ......................................... 4-43
5. INTERFACE, IC PIN FUNCTION DESCRIPTION
5-1. System Control-Video Block Interface
(MA-325 board IC161) .................................................. 5-1
5-2. System Control-Servo Peripheral Circuit Interface
(MA-325 board IC161) .................................................. 5-1
5-3. System Control-Mechanism Block Interface
(MA-325 board IC161) .................................................. 5-2
5-4. System Control-System Control Peripheral Circuit
Interface (MA-325 board IC161) ................................... 5-3
5-5. System Control-Hi-Fi Audio Block Interface
(MA-325 board IC161) .................................................. 5-3
5-6. Servo/System Control Microprocessor Pin Function
(MA-325 board IC161) .................................................. 5-4
5-7. Timer/Tuner Control Microprocessor Pin Function
(FR-137 board IC301) ................................................... 5-5
5-8. KOREAN Processor Pin Function
(NK-11 board IC1) ......................................................... 5-6
6. ERROR CODE.......................................................... 6-1
7. ADJUSTMENTS
7-1. Mechanical Adjustments ............................................... 7-1
7-2. Adjustments................................................................... 7-1
2-1. EEP ROM Initial Data Input .......................................... 7-1
7-3. Electrical Adjustments................................................... 7-1
3-1. Pre-Adjustment Preparations........................................ 7-1
3-1-1. Instruments to be Used............................................ 7-1
3-1-2. Connection ............................................................... 7-1
3-1-3. Set-up of Adjustment ............................................... 7-2
3-1-4. Alignment Tapes ....................................................... 7-2
3-1-5. Specified I/O Level and Impedance
Input/Output Terminal ............................................... 7-2
3-1-6. Adjusting Sequence ................................................. 7-2
3-2. Power Supply Adjustment ............................................. 7-2
3-2-1. Power Supply Check ................................................ 7-2
3-2-2. +6 V Adjustment ....................................................... 7-2
3-3. Servo System Adjustment............................................. 7-3
3-3-1. RF Switching Position Adjustment ........................... 7-3
3-4. Audio System Adjustments ........................................... 7-3
3-4-1. Hi-Fi Audio System Adjustment ............................... 7-3
1. AF Switching Position Adjustment ........................... 7-3
2. Frequency Response Check.................................... 7-4
3. Overall Level Characteristic and
Distortion Factor Check ........................................... 7-4
4. Overall S/N Check.................................................... 7-4
3-4-2. Normal Audio System Adjustment ........................... 7-5
1. ACE Head Adjustment ............................................. 7-5
2. E-E Output Level Check........................................... 7-5
3. Frequency Responce Check.................................... 7-5
4. Overall Level Characteristic and Distortion
Factor Check ............................................................ 7-5
5. Overall S/N Check.................................................... 7-5
3-5. Video System Adjustment ............................................. 7-5
3-5-1. VCO Oscillation Frequency Adjustment .................. 7-5
3-6. Parts Arrangement Diagram for Adjustments............... 7-6
8. REPAIR PARTS LIST
8-1. Exploded Views ............................................................. 8-1
8-1-1. Front Panel and Cabinet Assemblies (ED8)............ 8-1
8-1-2. Front Panel and Cabinet Assemblies (ED9)............ 8-2
8-1-3. Chassis Assembly .................................................... 8-3
8-1-4. Mechanism Chassis Assembly (1)........................... 8-4
8-1-5. Mechanism Chassis Assembly (2)........................... 8-5
8-1-6. Mechanism Chassis Assembly (3)........................... 8-6
8-2. Electrical Parts List........................................................ 8-7

– 4 –
SERVICE NOTE
1. DISASSEMBLY
• This set can be disassembled in the order shown below.
Note: Pages in indicated pages in the SERVICE MANUAL.
Pages in indicated pages in the VHS MECHANICAL ADJUSTMENT MANUAL VI.
NK-11 Board
(Page 2-1)
Set
Upper case
(Page 2-1)
Front Panel
Section
(Page 2-1)
Power
Block
(Page 2-3)
Rear Panel
(Page 2-1)
Pinch Press
Block Ass’y
(Page 14)
Ground Shaft
Ass’y
(Page 13)
Drum Ass’y
(Page 13)
RJ-79 Board
(Page 2-1)
Mechanism
Deck
(Page 2-2)
FR-137 Board
(Page 2-2)
FL complete
Ass’y
(Page 13)
FL Slider
Block Ass’y
(Page 22)
DM-77 Board
(Page 2-2)
SW-307 Board
(ED9)
(Page 2-2)
Rubber
Belt
(Page 15)
IO-64 Board
(Page 2-2) Retainer
Plate
(Page 22)
Rubber
Belt
(Page 15)
Capstan
Motor
(Page 15)
Control Switch
Block (ED9)
(Page 2-2)
Rotary
Switch
(Page 2-2) Tuner
Unit
Pully Gear
Ass’y
(Page 29)
Cam Gear
(Page 23) Cam Motor
Retainer
(Page 31)
Rubber
Belt
(Page 15)
Reel Direct
Ass’y
(Page 30)
Slider
(Page 26)
Loading
Gear (T, S)
(Page 28)
Cam Motor
(Page 31)
MA-325 Board
(Page 2-3) PS-414 Board
(Page 2-3)

1-1
SECTION 1
GENERAL Thissectionisextracted fromSLV-ED8KR
instruction manual (3-861-812-11).
SLV-ED8/ED9

1-2

1-3

1-4

1-5

1-6

1-7

1-8

1-9

1-10

1-11

1-12

1-13
1-13 E

2-1
Note: Follow the disassembly procedure in the numerical order given.
SECTION 2
DISASSEMBLY
2-1. UPPER CASE REMOVAL 2-3. REAR PANEL REMOVAL
2-2. RJ-79, NK-11 BOARD REMOVAL 2-4. FRONT PANEL SECTION REMOVAL
SLV-ED8/ED9
1Two tapping screws
2Two tapping screws
3Upper case
5NK-11 board
1Two connectors
(CN951, 952)
4Connector
(CN751)
3RJ-79 board
2Four screws
(BVTP3 ×12)
3Harness
5Two claws
4Three claws
6Claw
7Claw
8Rear panel
2Connector
(CN361)
1Two connectors
(CN101, 901)
1Connector
(CN423)
2Flat cable
(CN105)
3Two claws
4Claw
5Three claws
6Front panel section

2-2
2-5. FR-137, DM-77, SW-307, IO-64 BOARD
REMOVAL (ED9)
2-8. MECHANISM DECK REMOVAL
2-6. CONTROL SWITCH BLOCK REMOVAL
(ED9)
2-7. FR-137, DM-77, IO-64 BOARD
REMOVAL (ED8)
8DM-77 board
!™ IO-64
board
1Flat cable
(CN309)
5Flat cable
(CN308)
9Flexible board
(CN451)
6Flexible board
(CN302)
7Four screws
(B2.6 ×8)
3Four screws
(B2.6 ×8) 2Screw
(B2.6 ×8)
4FR-137 board
!¡ SW-307 board
0Two screws
(B2.6 ×8)
5Control switch block
2Damper holder
4Fulcrum plate
(right) assembly
1Two screws
(B2.6 ×8)
3Screw
(B2.6 ×8)
8IO-64 board
4Flexible board
(CN451)
2Four screws
(B2.6 ×8)
1Nine screws
(B2.6 ×8)
3FR-137 board
5Connector
(CN307)
6DM-77 board
7Screw
(B2.6 ×8)
1Flexible board
5Screw
(BVTP3 ×12)
4Screw
(B3)
6Two screws
(BVTP3 ×12)
7Mechanism deck
3Connector
(FE head)
2Connector
(ACE head)
Note: When mounting the mechanism deck,
first align ¢mark on the rotary switch.

2-3
2-9. POWER BLOCK REMOVAL
2-10. PS-414, MA-325 BOARD REMOVAL
1Power cord
3Power block
2Two screws
(B3)
6MA-325 board
3PS-414 board
2Three screws
(B3)
4Screw
(B3)
1Connector
(CN162)
5Three screws
(B3)