Soundcore Liberty 3 Pro User manual

Soundcore Liberty 3 Pro
USER MANUAL

English 01
Deutsch 12
Español 23
Français 34
日本語 45

01 EN
Charging
• Fully dry off the earbuds and the USB port before charging.
• Use a certified USB-C charging cable and charger to prevent any damage.
• Fully charge both the earbuds and the charging case before the first use.
1. Place the earbuds in the charging case and close it.
2. Connect the charging case to the power supply by using a USB-C charging
cable. Alternatively, position the charging case at the center of your wireless
charger for wireless charging.
• The LED indicators on the charging case indicate the charging status.
< 30%
30% - 70%
70% - 95%
>95%
or
21

EN 02
Wearing
Wearing the Earbuds
1. Insert the earbuds into your ears.
2. Twist the earbuds until the ear wings are wedged against the ridge of your ears.
12
• Use a mirror to check if you are wearing your earbuds correctly.
Your earbuds properly fit.
• The ear wings are wedged against
the ridge of your ear and you can feel
support from the backside.
• The ear tips feel stable in your ear
canal so that they can isolate ambient
sounds.
• The earbuds feel comfortable without
sticking out.
Your ear wings are too big.
• The ear wings stick out so that the
earbuds feel unstable and loose. (Or
your ear wings are squished under the
ridge of your ear.)
• The ear tips may not be deep enough
so they do not provide a comfortable
seal.
Your ear wings are too small.
• The ear wings do not touch the ridge
of your ear and get no support. The
earbuds may fall out when you move
your head.
• The ear tips may be so deep in your
ear canal that they cause too much
pressure and cannot be worn for a
long time.

03 EN
Changing the Ear Tips
1. Select the size of ear tips that fit your ears best.
2. Attach the ear tips to the earbuds. Ensure the ear tips are firmly attached.
XS 0 0
1 1
S
2 2
M
3 3
L
Changing the Ear Wings
1. Remove the current ear wings. Note that L2 and R2 ear wings are pre-installed.
2. Choose the best ear wing size for your ears.
R1
L1
R0
L0
R2
L2
R3
L3
R3
3. Align the oval hole on the ear wings with the wearing detection sensor on the
earbuds.
Wearing detection sensor

EN 04
4. Insert the earbuds into the ear wings through the narrow side.
5. Stretch the ear wings into position by holding the narrow side. Ensure the ear
wings are not folded.
Powering On/Off
Open the charging case, the earbuds will automatically power on.
To power off, place the earbuds in the charging case and close it.
ON
OFF
1
2
• To manually power on, wear both earbuds, then press and hold the touchpad on
both earbuds for 3 seconds.
• The earbuds will automatically power off after 30 minutes if they are not being
worn and are not connected.

05 EN
Bluetooth Pairing
Automatic Pairing*
1. Open the charging case, and the earbuds will automatically enter Bluetooth
pairing mode.
• The 2 LED indicators inside the charging case will flash white.
2. Select "Soundcore Liberty 3 Pro" on your device's Bluetooth list to connect.
• When successfully connected, the 2 LED indicators will pulse white.
1
PAIRING
2
Soundcore
Liberty 3 Pro
Soundcore
Liberty 3 Pro
CONNECTED
*Automatic pairing is available only for earbuds in factory mode.
Manual Pairing
1. Place the earbuds in the charging case and leave the case open.
2. Press and hold the button on the charging case for 3 seconds until the 2 LED
indicators inside the charging case flash white.
2
1
3s
PAIRING
Multipoint
The earbuds can connect with two Bluetooth devices at the same time. There are
two ways to pair with another device.

EN 06
Option 1: Enable "Dual device connection" and connect to the second device in
the Soundcore app.
Option 2: Wear the earbuds, then press and hold the touchpad on both earbuds
for 5 seconds simultaneously. Select "Soundcore Liberty 3 Pro" on the second
device's Bluetooth list to connect.
L R
5s 5s
12
Soundcore
Liberty 3 Pro
Soundcore
Liberty 3 Pro
• Each time you power on your Soundcore earbuds, they will automatically
connect to your last successfully connected device if available within the
Bluetooth range.
• Mono mode: When Bluetooth is connected, you can use either one of the
earbuds on its own by placing the other one into the charging case and closing it.
• When powered on and connected, if either one of the earbuds is out of battery
and powered off, you can keep using the other one.
• When you are on a call, place either one of the earbuds into the charging case,
and the microphone in the other earbud will be activated.

07 EN
Controls
Stereo Mode
×2 1s
L / R L / R
LR
×2 ×2
HearID ANC
Transparency
2s
L / R
Play/Pause Tap twice (R)
Next track Tap twice (L)
Switch ambient sound modes
(HearID ANC / Transparency / Normal*) Press and hold for 2 seconds (L/R)
*You can add "Normal" in the Soundcore app.
Answer/End a call Tap twice (L/R)
Reject a call Press and hold for 1 second (L/R)
Mono Mode
×2 ×2 1s
Siri
1s
Play/Pause Tap twice
Activate Siri or other voice assistant software* Press and hold for 1 second
Answer/End a call Tap twice
Reject a call Press and hold for 1 second
*You can enable this function in the Soundcore app.
• All of the controls in stereo mode can be customized in the Soundcore app. In
mono mode, controls cannot be customized in the app.

EN 08
• Adjust the volume level via the connected device or in the Soundcore app.
• In stereo mode, noise cancellation mode is set by default. Each time you power
on and connect, or switch to the stereo mode from mono mode, your earbuds
will restore the last setting.
• Noise cancellation or transparency mode is unavailable in mono mode.
Soundcore App
Download the Soundcore app to enhance your experience.
User interface customization: In stereo mode, all of the controls (e.g. adjust
volume, control playback, activate Siri) can be customized in the app.
EQ settings: There are more than 20 EQ settings you can choose from in the app
to optimize your experience while enjoying different music genres.
HearID Sound: HearID maps your personal hearing sensitivity at multiple
frequencies and analyzes the results. It traces the EQ settings and creates a
personalized sound profile for you.
HearID ANC: Take the ear canal test and tailor your noise cancellation experience.
• Adaptive mode: Adjust the level of noise cancelling automatically depending on
the noise levels in your surroundings to reduce pressure for a more comfortable
noise cancelling experience.
Transparency mode: Stay aware of your surroundings by allowing ambient
sounds in.
• Fully transparent: Hear all ambient sounds.
• Vocal mode: Voices stand out more clearly from other ambient sounds.
Earbuds firmware upgrade: You will be informed once the new version of
firmware is detected when you connect the earbuds with the app. Ensure the
earbuds are placed in the charging case and the case remains open until the
firmware upgrade is completed. During the upgrade, ensure the earbuds are
being charged and avoid any operation.