Soundcore Liberty Air 2 Pro User manual

Liberty Air 2 Pro
USER MANUAL

01 EN
Charging
• Remove the protective lm from the earbuds before the rst use.
• Fully dry off the earbuds and the USB port before charging.
• Use a certied USB-C charging cable and charger to prevent any damage.
• Fully charge both the earbuds and the charging case before the rst use.
1. Place the earbuds in the charging case and close it.
The rst and the third LED indicators on the charging case will ash twice. This
conrms that the earbuds are being charged.
2. Connect the charging case to the power supply by using a USB-C charging cable.
Alternatively, position the charging case at the center of your wireless charger for
wireless charging.
The LED indicators on the c harging case indicate the charging status.
2
1
< 30%
30% - 70%
> 70%
100%
or
3. To check the battery level of the charging case, open it to activate the LED
indicator.
10% - 30%
< 10%
30% - 70%
> 70%

EN 02
Soundcore App
Download the Soundcore app to enhance your experience.
HearID: HearID maps your personal hearing sensitivity at multiple frequencies and
analyzes the results. It traces the EQ settings and creates a personalized sound
prole for you.
User interface customization: In stereo mode, all of the controls (e.g. adjust volume,
control playback, activate Siri) can be customized in the app.
EQ settings: There are more than 20 EQ settings you can choose from in the app to
optimize your experience while enjoying different music genres.
Noise cancellation: Choose an active noise cancellation mode to reduce ambient
noise according to your surroundings.
• Transport: Targets low-end frequencies like engine and road noise for peaceful
journeys and commutes.
• Outdoor: Reduces ambient sounds in cities for less distractions.
• Indoor: Reduces voices and mid-frequency noise from coffee shops and other inside
spaces.
Custom ANC: Adjust the noise cancellation level to suit you in the app.
Transparency mode: Stay aware of your surroundings by allowing ambient sounds
in.
• Fully Transparent: Hear all ambient sounds.
• Vocal Mode: Voices stand out more clearly from other ambient sounds.
Earbuds rmware update: You will be informed once the new version of rmware
is detected when you connect the earbuds with the app. Ensure the earbuds are
placed in the charging case and the case remains open until the rmware upgrade
is completed. During the upgrade, ensure the earbuds are being charged and avoid
any operation.

03 EN
Wearing
1. Choose the EarTips that t your ears best.
2. Insert the earbuds into the inner canal of your ears and turn gently until you nd
the most comfortable and secure position.
21
XL MM+
XS XXS XXXSS
LL+
Your earbuds come with multiple pairs of EarTips, among which Medium-sized are
pre-installed.
Powering On/Off
Open the charging case, the earbuds will automatically power on.
The LED indicator on earbuds will light up white for 1 second.
To power off, place the earbuds in the charging case and it.
1OFF 2
ON
When you’re wearing the earbuds, they will not power off until out of battery. When
you remove the earbuds, they will automatically power off after 30 minutes if no
device is connected.

EN 04
Bluetooth Pairing
1. Open the charging case, the earbuds will automatically enter the Bluetooth
pairing mode.
The LED indicator on one earbud will flash quickly and on another earbud
breathe slowly.
2. Select “Soundcore Liberty Air 2 Pro” on your device’s Bluetooth list to connect.
When successfully connected, the LED indicator on earbuds will light up white
for 1 second.
1 2
Soundcore
Liberty Air 2 Pro
Soundcore
Liberty Air 2 Pro
• Each time you power on your Soundcore earbuds, they will automatically
connect to your last successfully connected device if available within the
Bluetooth range.
• Mono mode: When Bluetooth connected, you can use either one of the earbuds
only by placing the other one into the charging case and closing it.
• When powered on and connected, if either one of the earbuds is out of battery
and powered off, you can keep using the other one.
• When you are on a call, place either one of the earbuds into the charging case
and close it, the microphone in the other earbud will be activated.
Pairing with another device
1. Place the earbuds in the charging case and leave the case open. Press and hold
the button on the case for 3 seconds until the earbud LED indicators ash white to
enter the pairing mode.
2. Select “Soundcore Liberty Air 2 Pro” on your device’s Bluetooth list to connect.