Soundcore Liberty Air 2 Pro User manual

Liberty Air 2 Pro
USER MANUAL

English 01
Čeština 08
Dansk 15
Deutsch 22
ελληνικά 29
Español 36
Suomi 43
Français 50
Magyar 57
Italiano 64
Nederlands 71
Norsk 78
Język polski 85
Português 92
Portugues do Brasil 99
Pусский 106
Slovenský Jazyk 113
Slovenski Jezik 120
Svenska 127
Türkçe 134
日本語141
한국어148
简体中文155
繁體中文162
 169
  176

01 EN
Charging
• Remove the protective lm from the earbuds before the rst use.
• Fully dry off the earbuds and the USB port before charging.
• Use a certied USB-C charging cable and charger to prevent any damage.
• Fully charge both the earbuds and the charging case before the rst use.
1. Place the earbuds in the charging case and close it.
The rst and the third LED indicators on the charging case will ash twice. This
conrms that the earbuds are being charged.
2. Connect the charging case to the power supply by using a USB-C charging cable.
Alternatively, position the charging case at the center of your wireless charger for
wireless charging.
The LED indicators on the c harging case indicate the charging status.
2
1
< 30%
30% - 70%
> 70%
100%
or
3. To check the battery level of the charging case, open it to activate the LED
indicator.
10% - 30%
< 10%
30% - 70%
> 70%

EN 02
Soundcore App
Download the Soundcore app to enhance your experience.
HearID: HearID maps your personal hearing sensitivity at multiple frequencies and
analyzes the results. It traces the EQ settings and creates a personalized sound
prole for you.
User interface customization: In stereo mode, all of the controls (e.g. adjust volume,
control playback, activate Siri) can be customized in the app.
EQ settings: There are more than 20 EQ settings you can choose from in the app to
optimize your experience while enjoying different music genres.
Noise cancellation: Choose an active noise cancellation mode to reduce ambient
noise according to your surroundings.
• Transport: Targets low-end frequencies like engine and road noise for peaceful
journeys and commutes.
• Outdoor: Reduces ambient sounds in cities for less distractions.
• Indoor: Reduces voices and mid-frequency noise from coffee shops and other inside
spaces.
Custom ANC: Adjust the noise cancellation level to suit you in the app.
Transparency mode: Stay aware of your surroundings by allowing ambient sounds
in.
• Fully Transparent: Hear all ambient sounds.
• Vocal Mode: Voices stand out more clearly from other ambient sounds.
Earbuds rmware update: You will be informed once the new version of rmware
is detected when you connect the earbuds with the app. Ensure the earbuds are
placed in the charging case and the case remains open until the rmware upgrade
is completed. During the upgrade, ensure the earbuds are being charged and avoid
any operation.

03 EN
Wearing
1. Choose the Liquid Silicone EarTips that t your ears best.
2. Insert the earbuds into the inner canal of your ears and turn gently until you nd
the most comfortable and secure position.
21
XL MM+
XS XXS XXXSS
LL+
Your earbuds come with multiple pairs of EarTips, among which Medium-sized are
pre-installed.
Powering On/Off
Open the charging case, the earbuds will automatically power on.
The LED indicator on earbuds will light up white for 1 second.
To power off, place the earbuds in the charging case and it.
1OFF 2
ON
When you’re wearing the earbuds, they will not power off until out of battery. When
you remove the earbuds, they will automatically power off after 30 minutes if no
device is connected.

EN 04
Bluetooth Pairing
1. Open the charging case, the earbuds will automatically enter the Bluetooth
pairing mode.
The LED indicator on one earbud will flash quickly and on another earbud
breathe slowly.
2. Select “Soundcore Liberty Air 2 Pro” on your device’s Bluetooth list to connect.
When successfully connected, the LED indicator on earbuds will light up white
for 1 second.
1 2
Soundcore
Liberty Air 2 Pro
Soundcore
Liberty Air 2 Pro
• Each time you power on your Soundcore earbuds, they will automatically
connect to your last successfully connected device if available within the
Bluetooth range.
• Mono mode: When Bluetooth connected, you can use either one of the earbuds
only by placing the other one into the charging case and closing it.
• When powered on and connected, if either one of the earbuds is out of battery
and powered off, you can keep using the other one.
• When you are on a call, place either one of the earbuds into the charging case
and close it, the microphone in the other earbud will be activated.
Pairing with another device
1. Place the earbuds in the charging case and leave the case open. Press and hold
the button on the case for 3 seconds until the earbud LED indicators ash white to
enter the pairing mode.
2. Select “Soundcore Liberty Air 2 Pro” on your device’s Bluetooth list to connect.

05 EN
12
Soundcore
Liberty Air 2 Pro
Soundcore
Liberty Air 2 Pro
3”
Controls
Play/Pause Tap twice (R)
Next track Tap twice (L)
Answer a call
Tap twice (L/R)
Answer a second incoming call and put the
current call on hold
End/Reject a call Press and hold for 2 seconds (L/
R)
Switch between a call on hold and an active call
Switch ambient sound modes
(Noise Cancellation/Normal)
Press and hold for 2 seconds (L/
R)

EN 06
Mono mode
Play/Pause Tap twice
Answer a call
End/Reject a call Press and hold for 2 seconds
Activate Siri or other voice assistant software
• All of the controls in stereo mode can be customized in the Soundcore app. In
mono mode, controls cannot be customized in the app.
• Music playback will auto-pause when removing the earbuds, wear them again to
resume.
• Adjust the volume level via the connected device or in the Soundcore app.
• In stereo mode, noise cancellation mode is set by default. Each time you power
on and connect, or switch to the stereo mode from mono mode, your earbuds
will restore the last setting.
• Noise cancellation or transparency mode is unavailable in mono mode.
Reset
You might need to reset your earbuds if you experience any connectivity problems
or function issues.
1. Place the earbuds in the charging case and leave the case open.
2. Press and hold the button on the case for 10 seconds until the earbud LED
indicators ash red 3 times and then turn white.
3. Wait until the LED indicator on one of the earbuds flashes fast while the other
breathes slowly. This conrms that the reset was successful and your earbuds can be
connected normally.
1
3
2 3
10”
The following two examples indicate the reset has not been successful and the
previous steps should be repeated.

07 EN
• If only one earbud LED indicator ashes;
• If both earbud LED indicators ash quickly.
Specifications
Specications are subject to change without notice.
Input 5 V 0.5 A
Rated output power 5 mW @ 1% THD
Battery capacity 55 mA x 2 (earbuds);
500 mA (charging case)
Charging time 2 hours
15-minute charge = 3-hour playtime
Playtime
(varies by volume level and content)
Up to 7 hours
(Total 26 hours with the charging case)
Playtime
(with ANC mode turned on)
Up to 6 hours
(Total 21 hours with the charging case)
Playtime
(with transparency mode turned on)
Up to 6.5 hours
(Total 23 hours with the charging case)
Talk time Up to 4 hours
(Total 14 hours with the charging case)
Driver size 11 mm
Frequency response 20 Hz - 20 kHz
Impedance 16 Ω
Waterproof level
(The waterproof level may reduce
over time as a result of daily use)
IPX4
(The earbuds are not desig ned for swimming,
showering, or exposure to pool or ocean
water. Do not use in a sauna or steam room.
The charging case is not waterproof. )
Bluetooth version V 5.0
Bluetooth range 10 m / 33 ft

08 CS
Nabíjení
• Před prvním použitím odstraňte ze sluchátek ochrannou fólii.
• Před nabíjením sluchátka a port USB úplně vysušte.
• Použijte pouze certikovaný nabíjecí kabel USB-C a nabíječku, abyste zabránili
poškození.
• Před prvním použitím sluchátka i nabíjecí pouzdro úplně dobijte.
1. Sluchátka vložte do nabíjecího pouzdra a zavřete ho.
První a třetí LED kontrolka na nabíjecím pouzdře dvakrát zabliká. To potvrzuje, že
se sluchátka nabíjí.
2. Nabíjecí pouzdro pomocí nabíjecího kabelu USB-C připojte do elektřiny.Pokud
používáte bezdrátové nabíjení, můžete místo toho nabíjecí pouzdro umístit do
středu bezdrátové nabíječky.
LED kontrolky na nabíjecím pouzdře zobrazují stav nabíjení.
2
1
< 30%
30% - 70%
> 70%
100%
or
3. Chcete-li zjistit úroveň nabití baterie nabíjecího pouzdra, pouzdro otevřete, abyste
aktivovali LED kontrolku.
10% - 30%
< 10%
30% - 70%
> 70%