SOUNDMASTER TR100 User manual

TR100
DEUTSCH
ENGLISH
FRANÇAIS
NEDERLANDS
ESPAÑOL
PORTUGUÊS
ITALIANO
LIETUVOS
LATVIJAS
EESTI

IMPORTANT SAFETY INSTRUCTIONS
When used in the directed manner, this unit has been designed
and manufactured to ensure your personal safety.
However, improper use can result in potential electrical shock
or fire hazards. Please read all safety and operating instructions
carefully before installation and use, and keep these
instructions handy for future reference. Take special note of all
warnings listed in these instructions and on the unit.
Water and Moisture
The unit should not be used near water. For example: near a
bathtub, washbowl, kitchen sink, laundry tub, swimming pool or
in a set basement.
Ventilation
The unit should be situated so that its location or position does
not interfere with its proper ventilation. For example, it should
not be situated on a bed, sofa, rug or similar surface that may
block the ventilation openings. Also, it should not be placed in a
built-in installation, such as a bookcase or cabinet, which may
impede the flow of air through the ventilation openings.
Heat
The unit should be situated away from heat sources such as
radiators, heat registers, stoves or other appliances (including
amplifiers) that produce heat.
Power Source
The unit should be connected to a power supply only of the type
described in the operating instructions or as marked on the
appliance.
Cleaning
The unit should be cleaned only as recommended. See the

section ”Care and Maintenance” of this manual for cleaning
instructions.
Object and Liquid Entry Care should be taken so that objects do
not fall and liquids are not spilled into any openings or vents
located on the product.
Lightning and Power Surge Protection
Unplug the unit from the wall outlet. This will prevent damage to
the product due to lightning and power-line surges.
Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire of
electric shack.
Damage Requiring Service
This unit should be serviced by qualified service personnel
when:
Objects have fallen into or liquid has been spilled into the
enclosure.
The unit has been exposed to rain.
The unit has been dropped or the enclosure damaged.
The unit exhibits a marked change in performance or does not
operate normally.
Periods of Nonuse
If the unit is to be left unused for an intended period of time,
such as a week or longer, remove the battery to prevent
damage or injury from possible battery leakage.
Servicing
The user should not attempt to service the unit beyond those
methods described in the user’s operating instructions.
Service methods not covered in the operating instructions
should be referred to qualified service personnel.
1

LOCATIONS OF CONTROLS
FRONT VIEW
2

1. MODE button
-Press this button to select different play modes: RADIO/
AUX-IN /USB/CARD
2. Button
.In USB/CARD mode: to return to the beginning of current track
or previous track
.In radio memory selecting mode: to select the channel number
downward
3. Button.
.In USB/CARD mode: to advance to the next track
.In radio memory selecting mode: to select the channel number
upward
4. PRESET Button
.In Radio mode: to enter the radio memory selecting mode.
5. RPT(Repeat)/MEM Button
.In USB/CARD mode: to access to the Repeat-1, Repeat Folder,
Repeat All mode.
In Radio mode: to save radio preset station
3

6. Vol- Button
. To adjust volume level down
7. Vol+ Button
. To adjust volume level up
8. Button
.In USB/CARD mode: to start of interrupt play
9. SD/MMC card slot
10. USB port
11. 3.5mm AUX-IN Jack
12. Power ON/OFF Switch
13. USB Charge port
14. DC 5V Jack (for charging only)
15. Battery compartment
16. FM Telescopic Antenna
POWER SOURCE
This unit is operated by 1pc 3.7V rechargeable lithium ion
battery (included, which is exactly the same as the BL-5C
battery from Nokia).
BATTERY INSTALLATION
To install the battery:
1.) Remove the battery compartment door.
2.) Follow the polarity to install the accompanied 3.7V lithium
ion battery
3.) Replace the battery compartment door.
WARNING:
- Be sure that the battery is installed correctly.
- Only batteries of the same or equivalent type as recommend
are to be used.
4

- If the unit is not to be used for an extended period of time,
remove the battery to prevent damage or injury from possible
battery leakage.
-Do not dispose of the battery in fire, the battery may explode or
leak.
BATTERY CHARGING
The installed battery can be charged by using the accompanied
charger that you plug into the wall socket and the other end into
the DC5V charge port, the charging indicator on the charger will
light up with Red color, once it is fully charged, the light turns to
Blue.
It can also charge through the USB connector cable when
attached to a computer.
GETTING STARTED
Before the first use, we recommend to charge up the
accompanied battery for 4 hours to get the battery full.
Listening to FM Radio
Setting up the Antenna
Extend the telescopic antenna fully for best reception.
Tuning and Playing the Radio
1.Slide the Power ON/OFF switch to ON position to turn on the
unit.
2.Press MODE button on the main unit until FM icon appears on
the display to enter Radio mode.
3.Press /button to fine tune the radio frequency.
4. Press and hold /button for searching radio
frequency automatically.
5

Notes:
-Manual tune to select weaker stations that might be by skipped
during automatic tuning
-If the automatic tuning does not stop on the exact frequency of
the station, for example, it stops on 100.8MHz instead of
100.6MHz, use the manual tuning method to fine tune to the
exact frequency of the desired station.
-During FM Radio mode, if you plug USB or SD/MMC card into
the unit, the play mode will automatically change to USB or SD
playback mode.
Preset Stations
The unit allows you to store up to 30 FM stations for easy recall
at any time.
1.Tune to the radio station you want to store in memory by
using or button
2.Press RPT/MEM button, the memory channel number ”P
01” will show on the display, meanwhile, the Radio icon “FM”
flashes simultaneously
3.Press /button to select the channel number you
desire to set.
4.Press RPT/MEM button again to confirm the preset location.
5.Repeat steps 2-4 to store more stations if necessary.
Recalling Stored Preset Stations
1. Press PRESET button on the unit during Radio mode to
enter the radio memory selecting mode.
2. Press /button to select the preset channel
6

USB/SD OPERATION
1. Slide the Power ON/OFF switch to ON position to turn on the
unit.
2. Connect your USB device or SD/MMC card to the unit to
access “USB” or “CARD” mode, the relevant “USB” or “CARD”
icon appears on the display. The USB or SD/MMC card will start
playing automatically once the contents scanning is finished.
-Press “PLAY/PAUSE” button to pause or resume playback.
-Press “VOL+” or “VOL-” button to raise up/lower the volume
level.
-Press “ ” button to skip to next track or press “ ” button
to the previous track.
-Press and hold “ ” or “ ” button to search during the
desired music.
-Press “RPT/MEM” button to change the Repeat mode in the
following cyclical manner:
Repeat All (default repeat mode)→Repeat-1→Repeat older
- To remove your USB device or SD/MMC card, simply stop
the playback and gently unplug it from the connector.
AUX-IN (LINE IN) OPERATION
If you are using an iPod or other MP3/digital audio player which
can not plug in this unit directly, you can still play it on the unit
via an audio connecting cable.
1.Plug one end of the 3.5mm audio cable (excluded) into the
headphone or line out jack on your player, plug the other end of
cable into the unit AUX-IN jack of the unit.
7

2. Turn on the external audio source and play your device.
3. Slide the Power ON/OFF switch to ON position to turn on the
unit.
4. Press MODE button until “AUX” icon appears on the display.
5. The volume level can now be controlled through the main
unit. Operate all other functions on the external device as usual.
Notes:
1). If you're connected to the Line out Jack of your external
device, then you only need to adjust the volume control of this
unit. If you're connected to the Headphone Jack of your
external device, then you may need to adjust both the volume
control of your external device and the volume control of this
unit to find the most desirable volume setting.
2) Slide the Power ON/OFF switch to OFF position to turn off
the unit when you finish listening.
Don't forget to switch off the power of your external device as
well.
3). During AUX mode, if you plug USB or SD/MMC card into the
unit, the play mode will automatically change to USB or SD
playback mode.
8