SOUNDMASTER UR2090 User manual

DEUTSCH
PORTUGUÊS
ENGLISH
SVENSKA
FRANÇAIS
ČEŠTINA
NEDERLANDS
SLOVENSKÝ
ITALIANO
LIETUVOS
ESPANOL
UR2090
Hersteller
Wörlein GmbH Tel.: [phone]
Gewerbestrasse 12 Fax.: [phone]
D 90556 Cadolzburg Email. [e-mail]
GERMANY Web: www.woerlein.com

Safety, Environmental and Setup Instructions
EN
ENVIRONMENTAL PROTECTION
Do not dispose of this product with the normal household
waste at the end of its life cycle. Return it to a collection
point for the recycling of electrical and electronic devices.
This is indicated by the symbol on the product, user
manual or packaging
The materials are reusable according to their markings. By
reusing, recycling or other forms of utilization of old devices you
make an important contribution to the protection of our
environment.
Please contact your local authorities for details about collection
points.
WARNING
Risk of electric shock
Do not open!
Caution: To reduce the risk of electric shock, do not remove the
cover (or back). There are no user serviceable parts inside.
Refer servicing to qualified service personnel.
This symbol indicates the presence of dangerous
voltage inside the enclosure, sufficient enough to
cause electric shock.
This symbol indicates the presence of important
operating and maintenance instructions for the device
Used batteries are hazardous waste and NOT to be
disposed of with the household waste! As a
consumer you are legally obligated to return all
batteries for environmentally responsible recycling –
no matter whether or not the batteries contain harmful
substances*)
Return batteries free of charge to public collection points in your
community or shops selling batteries of the respective kind.
Only return fully discharged batteries
*) marked Cd = cadmium, Hg = mercury, Pb = lead
Only use mercury and cadmium-free batteries.
Used batteries are hazardous waste and NOT to be
disposed of with the household waste!!!
Keep batteries away from children. Children might swallow
batteries.
Contact a physician immediately if a battery was swallowed.
Check your batteries regularly to avoid battery leakage.
Batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly
replaced
Replace only with the same or equivalent type
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
This product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery
compartment does not close securely, stop using the product
and keep it away from children.
If you think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical attention.
CAUTION - INVISIBLE LASER
RADIATION WHEN OPENING THE
COVER OR PRESSING THE SAFETY
INTERLOCK. AVOID EXPOSURE TO
THE LASER BEAM.
Use the device in dry indoor environments only.
Protect the device from humidity.
This apparatus is for moderate climates areas
use, not suitable for use in tropical climates
countries.
No objects filled with liquids, such as vases, shall
be placed on the apparatus.
The mains plug or an appliance coupler is used
as the disconnect device, the disconnect devices
shall remain readily operable.
Connect this device to a properly installed and
earthed wall outlet only. Make sure the mains
voltage corresponds with the specifications on
the rating plate.
Make sure the mains cable stays dry during
operation. Do not pinch or damage the mains
cable in any way.
A damaged mains cable or plug must
immediately be replaced by an authorized service
center.
In case of lightning, immediately disconnect the
device from the mains supply.
Children should be supervised by parents when
using the device.
Clean the device with a dry cloth only.
Do NOT use CLEANING AGENTS or ABRASIVE
CLOTHS!
Do not expose the device to direct sunlight or
other heat sources.
Install the device at a location with sufficient
ventilation in order to prevent heat accumulation.
Do not cover the ventilation openings!
Install the device at a safe and vibration-free
location.
Install the device as far away as possible from
computers and microwave units; otherwise radio
reception may be disturbed.
Do not open or repair the enclosure. It is not safe
to do so and will void your warranty. Repairs only
by authorized service/ customer center.
No naked flame sources, such as lighted
candles, should be placed on the unit.
When you are necessary to ship the unit store it
in its original package. Save the package for this
purpose.
In case of malfunction due to electrostatic
discharge or fast transient (burst), remove and
reconnect the power supply.
If the unit is not using for a long period of time,
disconnect it from the power supply by
unplugging the power plug. This is to avoid the
risk of fire.
The device is equipped with a “Class 1 Laser”.
Avoid exposure to the laser beam as this could
cause eye injuries.

UR2090 / English Instruction Manual
1
LOCATION OF CONTROLS
FRONT VIEW
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18
SIDE VIEW
19
LINE IN jack
20
USB port
19 20
REAR VIEW
21 22
1
POWER button
2
SOURCE button
3
Mounting Peg
4
M+/10+ button
5
CD Tray
6
Remote Sensor
7
Display
8
SKIP/TUNE
Forward button
9
VOLUME+ button
10
OPEN/CLOSE
11
TIMER button
12
M-/10- button
13
P-MODE/
CLOCK SET/
MEMORY button
14
DISPLAY button
15
PLAY/PAUSE
PAIR button
16
STOP button
17
SKIP/TUNE
Backward button
18
VOLUME- button
21
DC IN jack
22
FM antenna

UR2090 / English Instruction Manual
2
AC Outlet
INSTALLATION
1. AC POWER
Use only the included power adapter. Plug the adapter into a standard wall outlet and the
DC plug into the DC jack at the rear side of the main unit.
2. Backup Battery
The device requires 2 AA-size batteries (not included).
The backup battery is intended for short power outages
only.
The unit´s primary functions cannot run on the backup
battery alone.
3. Remote Control (magnetic)
The remote control requires one CR2025 lithium battery (included). All of the above controls
are duplicated on the unit´s remote control.
The procedure for replacing the remote´s CR2025
battery is also detailed on the back of the remote.
Warning:
1. Be sure that the batteries are installed correctly.
Wrong polarity may damage the unit.
2. Use only the same size and type of batteries.
3. Do not mix old and new batteries.
4. Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
5. If the unit is not to be used for an extended period of
time remove the batteries.
6. Do not try to recharge the batteries which are not
intended to be recharged. They can overhead
and rupture.
AC Adapter
Push
here
Slide
out

UR2090 / English Instruction Manual
3
CLOCK
Setting the clock
1. When the unit is in Standby press and hold the “CLK SET/MEM”button. The hour on the
display will begin flashing.
2. Press the “SKIP/TUNE / ”buttons to adjust the hour.
3. Press the “CLK SET/MEM”button again to adjust the minutes. The minutes on the display
will begin flashing.
4. Press the “SKIP/TUNE / ”buttons to adjust the minutes.
5. Press the “CLK SET/MEM”button to finish setting the time or wait for the display to stop.
TIMER
Setting the Timer
1. Press the “TIMER”button. At the display the TIMER indicator will flash.
2. Press the “TIMER”button to adjust the timer in increments of 10 minutes.
3. Press the “SKIP/TUNE / “buttons to adjust the timer in increments of 1 minutes.
4. Wait until the display stop flashing
5. After the set time has expiered the device will sound an alarm.
Disabling the timer
To cancel the alarm after it has sounded press the “POWER”button or the “TIMER”button.
To cancel the timer before the alarm has sounded press the “TIMER”button until the display
shows “000”and the timer light is no longer lit.
CD OPERATION
The unit is compatible with MP3 CDs.
1. Turn the device on and press the “SOURCE”button to switch to CD mode.
2. Press the “OPEN/CLOSE”button to open the CD tray.
3. Place a CD into the tray with the label side facing up.
4. Press the “OPEN/CLOSE”button again to close the CD tray. The CD will starts playing
automatically.
5. Press the “PLAY/PAUSE”button to interrupt the playback. Press the button again to
resume playing.
6. Press the “SKIP/TUNE / ”buttons to select a track.
7. Press the “M+/10+”or “M-/10-“buttons to skip down or up by 10 tracks.
8. Press the “STOP ”button to stop the play mode.
Programming a CD
1. Press the “STOP ”button to stop the CD during play.
2. Press the “CLK SET/MEM”button.
3. “Prog” will begin to blink on the display.
4. Press the “SKIP/TUNE / ”buttons to select a track.
5. Press the “CLK SET/MEM”button to save the selected track to the program.
6. Repeat step 4 and 5 to program up to 20 tracks.
7. If you are ready press the “PLAY/PAUSE”button to start playing the programed titles.

UR2090 / English Instruction Manual
4
USB OPERATION
1. Insert the USB memory device into the USB socket.
2. Turn the device on and press the “SOURCE”button to switch to USB mode. The display will
show “USB”.
3. After reading the display shows the tracks of the USB device and starts playback
automatically.
4. Press the “PLAY/PAUSE”button to interrupt the playback. Press the button again to resume
playing.
5. Press the “SKIP/TUNE / ”button to select a track.
6. Press the “M+/10+”or “M-/10-“button to skip down or up by 10 tracks.
7. Press the “STOP ”button to stop the play mode.
NOTE:
The unit may not support some USB devices. This is due to the incompatibility of some
processors.
Repeat Function
Repeat one track on Music CD, MP3 Disc or USB
1. During CD/MP3 disc or USB playback press the “SKIP/TUNE / “buttons to select the
track which you want to repeat.
2. Press the “P-MODE”button until the “ 1” indicator shows on display. The unit will play the
selected track repeatedly.
3. To cancel the setting press the “P-MODE”button continuously until the “ 1” or “ALL”
indicators disappear.
Repeat the entire DISC or USB device
1. During CD/MP3 disc or USB playback press the “P-MODE”button continuously until the
“ALL” indicator shows on the display. The unit will play all tracks on the disc repeatedly.
2. To cancel the setting press the “P-MODE”button continuously until the “ 1” or “ALL”
indicators disappear.
RADIO
To improve the best FM radio reception try altering the position/length of the FM wire antenna.
1. Turn the device on and press the “SOURCE”button to switch to FM radio mode.
2. Press the “SKIP/TUNE / ”buttons to tune the radio manually in 50kHz steps.
3. Press and hold the “SKIP/TUNE / ”buttons to scan for available stations.
Saving and playing a station as a Preset
1. Press the “SKIP/TUNE / “buttons to tune the FM radio to the desired station.
2. Press the “CLK SET/MEM”button. Preset number (P01) will appear on the display.
3. Press the “M+/10+”or “M-/10-“buttons to adjust the desired preset number (P01-P20).
4. Press the “CLK SET/MEM”button to save the current FM radio station to this selected
preset.
5. Repeat steps 1 to 4 to program further radio stations.
6. Press the “M+/10+ or “M-/10-“buttons to cycle through saved radio stations.

UR2090 / English Instruction Manual
5
BLUETOOTH FUNCTION
Pairing to a device and playing audio
1. Turn the device on and press the “SOURCE”button to switch to BLUETOOTH mode.
The Bluetooth indicator will light up.
2. Press and hold the “PAIR/PLAY/PAUSE”button to begin pairing. The indicator on the
display will begin flashing quickly.
3. Start the Bluetooth mode on your Bluetooth device and start the scan. Select “UR2090SI in
your setting to pair it. If your device requests a password enter the default password “0000”.
4. When the devices are successfully paired the indicator on the display will stop flashing and
an audible chime will sound through the speaker.
5. Use the controls on the connected device to select an audio track, to start the playback,
pause etc.
After initial pairing the unit will stay paired unless you manually disconnect the connection or the
devices are out of range.
AUX-IN FUNCTION
You require a 3.5mm audio cable (not included).
1. Connect a 3.5mm audio cable to the “LINE IN”input on the right side of the unit and the
audio output on an audio device.
2. Turn the device on and press the “SOURCE”button to switch to LINE IN mode.
3. Use the controls on the connected device to start the playback.
TECHNICAL SPECIFICATION
Power supply
: Use only the supplied power adapter
Power input
: 100-240V~ 50/60Hz
Power output
: 5V 1.2A
Backup Battery
: 2x DC 1.5V UM-3 AA type batteries (not included)
FM range
: 87.5 –108MHz
Bluetooth Version
: Version 4.2
Audio power output
: 2x 2W RMS
IMPORTER
Wörlein GmbH Tel.: [phone]
Gewerbestrasse 12 Fax.: [phone]
D 90556 Cadolzburg Email: [email protected]
Germany Web: www.woerlein.com
Technische Änderungen und Druckfehler vorbehalten
Copyright by Woerlein GmbH, 90556 Cadolzburg, www.woerlein.com
Vervielfältigung nur mit ausdrücklicher Genehmigung der Woerlein GmbH

Hiermit bestätigt Wörlein GmbH, dass sich dieses Gerät
in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen
Bestimmungen der Richtlinie 2014/53/EU befindet.
Eine Kopie der Konformitätserklärung kann unter
folgender Adresse bezogen werden.
Wörlein GmbH, Gewerbestrasse 12, D 90556 Cadolzburg,
Germany
Email: inf[email protected]om
Tel.: [phone]
Hereby, Wörlein GmbH declares that this device is in
compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU.
A copy of the Declaration of Conformity may be
obtained at the following location:
Wörlein GmbH, Gewerbestrasse 12, D 90556 Cadolzburg,
Germany
Email: inf[email protected]om
Tel.: [phone]
Par la présente, Wörlein GmbH déclare que cet appareil
est conforme aux exigences principales et autres clauses
applicables de la Directive 2014/53/EU.
Vous pouvez demander de recevoir une copie de la
déclaration de conformité en écrivant à l'adresse
suivante :
Wörlein GmbH, Gewerbestrasse 12, D 90556 Cadolzburg,
Germany
Email: inf[email protected]om
Tel.: [phone]
Wörlein GmbH verklaart hierbij dat dit apparaat in
overeenkomst is met de essentiële vereisten en andere
relevante bepalingen van de Richtlijn 2014/53/EU.
Er kan een kopie van de Conformiteitsverklaring worden
verkregen op de volgende locatie:
Wörlein GmbH, Gewerbestrasse 12, D 90556 Cadolzburg,
Germany
Email: inf[email protected]om
Tel.: [phone]
Con la presente, Wörlein GmbH dichiara che questo
dispositivo è conforme ai requisiti essenziali e altre
disposizioni contenute nella Direttiva 2014/53/EU.
Una copia della Dichiarazione di conformità è disponibile
al seguente indirizzo:
Wörlein GmbH, Gewerbestrasse 12, D 90556 Cadolzburg,
Germania
Email: inf[email protected]om
Tel .: [phone]
Härmed Wörlein GmbH deklarerar att denna enhet är i
överensstämmelse med de grundläggande kraven och
andra relevanta bestämmelser i direktiv 2014/53/EU.
En kopia av försäkran om överensstämmelse kan erhållas
på följande plats:
Wörlein GmbH, Gewerbestrasse 12, D 90.556
Cadolzburg, Tyskland
E-post: inf[email protected]
Tel .: [phone]
Herved Wörlein GmbH erklærer, at denne enhed er i
overensstemmelse med de væsentlige krav og øvrige
relevante krav i direktiv 2014/53/EU.
En kopi af Overensstemmelseserklæringen kan fås på
følgende placering:
Wörlein GmbH, Gewerbestrasse 12, D 90556 Cadolzburg,
Tyskland
E-mail: inf[email protected]om
Tel .: [phone]
Tímto Wörlein GmbH prohlašuje, že toto zařízení je ve
shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 2014/53/EU.
Kopii Prohlášení o shodě lze získat v následujícím
umístění:
Wörlein GmbH, Gewerbestrasse 12, D 90556 Cadolzburg,
Německo
E-mail: inf[email protected]om
Tel .: [phone]
Por este meio, Wörlein GmbH declara que este
dispositivo está em conformidade com os requisitos
essenciais e outras disposições da Directiva 2014/53/EU.
Uma cópia da Declaração de Conformidade pode ser
obtida no seguinte local:
Wörlein GmbH, Gewerbestrasse 12, D 90556 Cadolzburg,
Alemanha
Email: [e-mail]
Tel .: [phone]