SPAccessories Classic Lifter Instructions for use

Spa & Hot Tub Necessities
Cover Classic Lifter
Installation & Use Manual

USE OF THIS DEVISE WITH OLD, WATERLOGGERD COVER
MAY DAMAGE COVER AND LIFTER
NOTE: THERE MUST BE 18” CLEARANCE BEHIND THE SPA.
The Premium Cover Lifter adjusts to t most square/rectangular spas up to
99” in width. When assembled it forms a rectangular shape. The Premium
Cover Lifter attaches to the back of the spa cabinet, either on the back wall
of the cabinet or on the pedestal base. The Bridge Arm (C) lies across the spa
cover parallel to the seam (hinge) of the cover and is “captured” when the
cover is folded back over it. Once the cover is folded back, simply lift back
on the Side Arm and the Premium Cover Lifter will lift the cover off the spa
and hold it in an upright position behind the spa. Pilot holes are pre-drilled
in the Corner Pieces (A). Once sized to your spa, the self-tapping screws will
penetrate the Bridge Arms and Side Arms (B) to lock the tubing in place. Be-
fore assembling the Premium Cover Lifter, check the components in the box
against the Parts List to insure all parts are present. You will need a power/
cordless drill with Phillips bit and a tape measure.

PARTS LIST
A
B
C
D
E
F
Part Description QTY
A Corner Piece 4
B 42” Side Arm 2
C 59” Bridge Arm 2
D Mounting Block 3
E Retaining Chain 2
F Chain Bracket 2
Metal Screw #10 x 5/8” 34
Wood Screw #8 x 5/8” 6
Wood Screw #8 x 1-1/4” 8
G Towel Holder 1
G

1. Lay out the components in the shape of a rectangle as shown below (Fig A). There are 2 sets of
Corner Pieces (A). They have been drilled so that the top left and bottom right are the same as are
the top right and bottom left. When assembling, position all Corner Pieces so that the pre-drilled
holes are FACING UP. NOTE: The LONG SIDE of the Corner Pieces goes Across the spa. The
SHORT side goes on each SIDE of the spa.
2. Side Mounting Blocks (D) over the LONG SIDE of each of the two bottom Corner Pieces
(A) as shown in Fig A. Remember, EACH CORNER PIECE MUST HAVE THE
PRE-DRILLED HOLES FACING UP.
Corner
Piece
Corner
Piece
Corner Piece (A)
Corner Piece (A) Mounting Blocks (D)
BOTTOM
59” Bridge Arm
(C)
59” Bridge Arm
(C)
TOP
Pilot Holes
Face Up
Pilot Holes
Face Up
42” Side Arm (B)42” Side Arm (B)
Fig. A
3.Slide one of the 59” Bridge Arms (C) into each of the two Bottom Corner Pieces (A) as
shown in Fig A. Repeat the process for the Top Corner Pieces. You now have two assembled
pieces, the top and bottom sections.
4. Measure the maximum width of your spa. Slide the 2 Corner Pieces in on the each Bridge
Arm until the width matches the width of your spa cabinet plus 3”. Be sure to slide the Bridge
Arm an equal distance into each Corner Piece. Make sure Mounting Blocks are outboard of all
screws. With the assembled pieces laying at on a level surface, secure the Bridge Arms to the
4 Corner Pieces with the enclosed #10 x 5/8 self-drilling screws. Tighten all screws completely.
See Fig. B.

Fig. B
Mounting Blocks
1.5” clearance between spa and inside arm of Premium Cover Lifter
Spa Cover
Premium
Cover Lifter
Bridge Arm
1/2” from spa
cover seam
Mounting
Blocks
Fig. C
5. Next connect these two assembled pieces together with the Side Arms (B) by sliding the
Side Arms into each of the four Corner Pieces as shown in Fig. A DO NOT secure with screws
yet.
6. With the Spa Cover in place on your Spa, lay the assembled rectangle assembly on the spa
with the Mounting Blocks at the bottom as shown in Fig. C. Remember, screws face up.

7. Mount the Mounting Blocks as wide and as low as possible. Attach the two Mounting
Blocks to the cabinet pedestal or base of spa cabinet if there is no pedestal, with the 1-1/4”
Wood Screws provided. NOTE: Mounting Blocks may be attached directly to deck
surface or use Universal adaptor bracket available from your dealer for round, oval or
octagonal spas.
8. Pull out/Push in on the top Corner/Side Arm assembly to adjust the Cover Butler so that
the Bridge Arm is about 1/2” behind the fold seam of the spa cover as shown in Figure C. The
Bridge Arm must be parallel to the cover fold seam. Be sure to slide the Side Arms an equal
distance into each Corner Piece. Before you attach the side arms into the top corners, deside
which side you would like the towel holder to be attached to. Line up the holes on the towel
holder with the holes on the side.corner pieces. Secure the Side Arms to each Corner Piece
with #10 x 1-1/4” screws. Use 3 screws per connection for all connections.
9. Center Premium Cover Lifter on spa so that there is approximately 1-1/2” clearance on each
side between spa and the inside of Premium Cover Lifter tubing. Screw in one #10 x 5/8”
self-drilling metal screw just to the outside of each Mounting Block to lock Premium Cover
Lifter into this position and prevent it from moving side to side. See Figure B.
10. Insert one #10 x 5/8” self-drilling metal screw through the end of one Retaining Chain
(D). Fold spa cover back and lift cover with Premium Cover Lifter until cover is hanging
vertically behind spa. Attach Retaining Chain to OUTSIDE of Side Arm of Premium Cover
Lifter approximately parallel with top of spa cabinet. Tighten screw securely but make sure
that chain can move freely on screw shaft. Attach the other end of the chain to the center hole
in the Chain Bracket (F) with a #10 x 5/8” self-drilling metal screw. With cover hanging
vertically behind spa with about 1” between spa cover and the back of the spa cabinet
(Premium Cover Lifter will be in a slightly over-vertical position), attach the Chain Bracket
to the spa cabinet with three #8 x 5/8” wood screws. The Retaining Chain should be
approximately parallel with the ground, but this is NOT critical to operation. Tighten Screw
securely, but make sure chain can move freely on screw shaft. See Figure D.
18” clearance
behind spa
Attach retaining chain to Premium Cover Lifter
and spa cabinet
INSTALLATION IS NOW COMPLETE

LIMITED LIFETIME WARRANTY
SPAccessories warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a Limited Lifetime Warranty.
This warranty extends only to the original purchaser. SPAccessories’ obligation
under this warranty is limited to replacing or repairing, at SPAccessories’ option,
the product at one of its authorized service centers. All products for which warranty
claim is made must be received by SPAccessories at one of its authorized service
centers with all freight and other transportation charges prepaid, accompanied by
sufcient proof of purchase. All returns must be pre-authorized by SPAccessories.
This warranty does not extend to any product or damage to a product caused by
or attributable to freight damage, abuse, misuse, improper or abnormal usage or
repairs not provided by a SPAccessories authorized service center, products used for
commercial or rental purposes, or products used as store display models. No other
warranty beyond that specically set forth above is authorized by SPAccessories.
SPAccessories is not responsible or liable for indirect, special or consequential
damages arising out of or in connection with the use or performance of the product
or damages with respect to any economic loss, loss of property, loss or revenues or
prots, loss of enjoyment or use, costs of removal, installation or other consequential
damages of whatsoever nature. Some states do not allow the exclusion or limitation
of incidental or consequential damages. Accordingly, the above limitation may not
apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any
implied warranties of merchantability or tness for a particular purpose is limited
in its scope and duration to the terms set forth herein. Some states do not allow
limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specic legal rights. You may also have other rights which
vary from state to state.
SPAccessories, 6848 S. Airport Rd., West Jordan, UT 84084

Spa & Hot Tub Necessities
SPAccessories, LLC.
11900 N. La Canada Dr. #69792
Tuscon, AZ 85737