SPAccessories CRS4 Instructions for use

S
p
a & Hot Tub Necessities
Premium Top Mount Hydraulic
Cover Removal System
Installation & Use Manual

BEFORE YOU START: Determine whether spa will need a Top Mount or a Side Mount installation.
1. PARTS LIST 2. TOOL LIST
The following parts are included in your CRS4 Cover Lift
package:
The following are needed to install your CRS4 Cover Lift.
Two (2) Pre-assemble Pivot Assemblies Power drill with 1/4” drill bit
1 - Left 1/2” open wrench
1 - Right 1/2” socket wrench
Two (2) Side Mount Brackets Phillips head screw driver
Two (2) Lock Knobs 9/16” socket wrench
Ten (10) 3/4” Hex Bolts Awl
Ten (10) Flat Washers Tape Measure
Twelve (12) Nylock Nuts Wear Protective Eye Wear
Eight (8) 1-1/4” Lag Bolts WARNING:

All hardware must be properly tightened
before operation of lifft. Failure to do so
may result in injury or damage to lift/spa.
Two (2) Phillips Pan Head Screws
Two (2) Handle Bars
One (1) Torsion Bar
!
3. DETERMINING WHICH TYPE OF INSTALLATION IS RIGHT FOR YOUR HOT TUB
1. PLEASE consider the following before installing your Cover Lift:
a. The Channel Bracket (pre-assembled Pivot Assembly) should be
mounted 2 - 5 “ from the back edge of your hot tub.
b. The Pivot Assembly should not interfere with your hot tub cover.
c. Determine whether or not the Side Mount Braackets are necessary
for installing the Cover Lift to your hot tub. (See A & B below)
A.
Use the Side Mount Brackets to assemble your
Cover Lift when:
B.
DO NOT use the Side Mount Brackets to assemble your
Cover Lift when:
a. the top rail around your hot tub is not wide
enough to accomondate the Channel Bracket
of the Pivot Assembly OR
b. the Cover Lift is the same size or wider than
the wood rim of your hot tub’s cabinet.
a. the Channel Brackets of the Pivot Assembly can be
mounted direcctly to the deck of an in-ground hot tub
b. OR the Channel Brackets can be mounted directly to
the top of your hot tub’s cabinet without interfering
with the Cover Lift.
WARNING
PLEASE READ ALL INSTRUCTIONS BEFORE
ATTEMPTING INSTALLATION
FAILURE TO DO SO MAY CAUSE PERSONAL INJURY OR DAMAGE TO YOUR LIFT
AND/OR SPA COVER
CAUTIONS
Extreme Caution:
• Be sure to use extreme caution during the Hydraulic Lift Arm phase of the assembly. A potential for suddem impact
is possible.
• Do not cut the red retaining straps until instructed to do so.
• BEFORE ASSEMBLY: Make sure there are no overhead
objects that could interfere with the cover’s designed
operation (lights, wires, branches, etc.).
1. Be sure to read all installation steps before beginning.
2. Many steps only show the installation of your cover lifter
on one side of your hot tub.
3. To complete your installation, repeat the same steps on the opposite side of your hot tub.
Pivot Assembly (Pre-Assembled)
Lock Bar Safety Tie Extension
Shipping Bolt

3. DETERMINING WHICH TYPE OF INSTALLATION IS RIGHT FOR YOUR HOT TUB
1. PLEASE consider the following before installing your Cover Lift:
a. The Channel Bracket (pre-assembled Pivot Assembly) should be
mounted 2 - 5 “ from the back edge of your hot tub.
b. The Pivot Assembly should not interfere with your hot tub cover.
c. Determine whether or not the Side Mount Braackets are necessary
for installing the Cover Lift to your hot tub. (See A & B below)
A.
Use the Side Mount Brackets to assemble your
Cover Lift when:
B.
DO NOT use the Side Mount Brackets to assemble your
Cover Lift when:
a. the top rail around your hot tub is not wide
enough to accomondate the Channel Bracket
of the Pivot Assembly OR
b. the Cover Lift is the same size or wider than
the wood rim of your hot tub’s cabinet.
a. the Channel Brackets of the Pivot Assembly can be
mounted direcctly to the deck of an in-ground hot tub
b. OR the Channel Brackets can be mounted directly to
the top of your hot tub’s cabinet without interfering
with the Cover Lift.
Channel Bracket is mounted directly to the top of
the wood rim of the cabinet. The cover moves freely
between the cover lift and hot tub.
Side Mount Bracket is mounted to the side of the hot tub’s
cabinet in order to leave room for a cabinet size cover.
Channel Bracket is offset of the top of a Side Mount
Bracket; bringing the Pivot Assembly 2” - 5” from the
back edge of the hot tub cover.
Side Mount Bracket is mounted to the side of the hot
tub’s top rail on the rst at surface approximately 2” - 5”
from the corner of the hot tub.
Side Mount Brackets
Figure 1
2 - 5”
Figure 2
2 - 5”
Figure 3
- 5”
Figure 4
2 - 5”

ASSEMBLY
A. Mounting Brackets
1. Install Mounting Brackets so that when the cover is lifted it is on the side opposite
the control panel of the hot tub.
2. Measure 1-1/2” from end of cabinet edge from kitty corner ush to cut line. (g. 1)
3. Mark holes, on center, with marker on both sides of the hot tub. (gure 1)
4. Use one bracket or level to level the bracket while marking and drilling holes.
5. Drill holes on bracket marks to a depth of 3/4” using 1/4” drill bit
6. Using a 1/2” socket wrench, install Mounting Brackets with screws provided
B. Hydraulic Lift Arm
EXTREME CAUTION:Be sure to use extreme caution during this phase of assembly. A potential for
sudden impact is possible. Do not cut the RED retaining straps until instructed to do so.
1. Using a 9/16” socket wrench, loosen the nut (shipping bolt) marked “Under
pressure”. (see gure 2)
2. Remove the Shipping Bolt and replace it with the Lock Knob making sure that the
conical spring washers are facing concaved sides towards each other (see gure 3)
3. Tighten the Lock Knob till it offers rm resistance
4. Making sure Extension Bar is pointed away from your face and other body parts.
5. Make sure Lock Knob is tightened.
6. Cut RED retaining strap and discard strap.
7. The Gas Shock of the Pivot Assembly is under pressure. Use extreme caution on
steps 8 and 9.
8. Placing Channel Bracket on ground, place hand over Extension Bar and exert
force downward while slowly loosening the Lock Knob.
9. Gently release pressure exerted from hand on Extension Bar assembly and
allow the gas shock to expand to full extension.
C. Pivot Assembly Installation
Side Mount Bracket Installation
1. With Pivot Assembly fully expoanded, place ve (5) 1/2” bolts with washers through
holes in Assembly and Side Mount Bracket carefully lining up same. (gure 4)
2. Secure with Nylock Nuts but DO NOT TIGHTEN
3. Once bolts are in place, slide assemblies as far away from the sides of cabinet as it
will go.
4. Tighten bolts starting with the center bolt and alternating till all bolts are
tightened down.
No Side Mount Bracket Required Installation
1. With Pivot Assembly fully expoanded, place ve (5) 1/2” bolts with washers through
holes in Assembly and line up carefully with holes in top or side of hot tub cabinet.
(gure 5)
2. Secure with Nylock Nuts but DO NOT TIGHTEN
3. Tighten bolts starting with the center bolt and alternating till all bolts are
tightened down.
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
2 - 5” from edge
1-1/4” Lag Bolts
1-1/4” Lag
Bolts
2 - 5”
2 - 5”
Shipping
Bolt
Spring Washers
LOCK KNOB
3/4” Hex
Bolts
Flat
Washers

ASSEMBLY
A. Mounting Brackets
1. Install Mounting Brackets so that when the cover is lifted it is on the side opposite
the control panel of the hot tub.
2. Measure 1-1/2” from end of cabinet edge from kitty corner ush to cut line. (g. 1)
3. Mark holes, on center, with marker on both sides of the hot tub. (gure 1)
4. Use one bracket or level to level the bracket while marking and drilling holes.
5. Drill holes on bracket marks to a depth of 3/4” using 1/4” drill bit
6. Using a 1/2” socket wrench, install Mounting Brackets with screws provided
B. Hydraulic Lift Arm
EXTREME CAUTION:Be sure to use extreme caution during this phase of assembly. A potential for
sudden impact is possible. Do not cut the RED retaining straps until instructed to do so.
1. Using a 9/16” socket wrench, loosen the nut (shipping bolt) marked “Under
pressure”. (see gure 2)
2. Remove the Shipping Bolt and replace it with the Lock Knob making sure that the
conical spring washers are facing concaved sides towards each other (see gure 3)
3. Tighten the Lock Knob till it offers rm resistance
4. Making sure Extension Bar is pointed away from your face and other body parts.
5. Make sure Lock Knob is tightened.
6. Cut RED retaining strap and discard strap.
7. The Gas Shock of the Pivot Assembly is under pressure. Use extreme caution on
steps 8 and 9.
8. Placing Channel Bracket on ground, place hand over Extension Bar and exert
force downward while slowly loosening the Lock Knob.
9. Gently release pressure exerted from hand on Extension Bar assembly and
allow the gas shock to expand to full extension.
C. Pivot Assembly Installation
Side Mount Bracket Installation
1. With Pivot Assembly fully expoanded, place ve (5) 1/2” bolts with washers through
holes in Assembly and Side Mount Bracket carefully lining up same. (gure 4)
2. Secure with Nylock Nuts but DO NOT TIGHTEN
3. Once bolts are in place, slide assemblies as far away from the sides of cabinet as it
will go.
4. Tighten bolts starting with the center bolt and alternating till all bolts are
tightened down.
No Side Mount Bracket Required Installation
1. With Pivot Assembly fully expoanded, place ve (5) 1/2” bolts with washers through
holes in Assembly and line up carefully with holes in top or side of hot tub cabinet.
(gure 5)
2. Secure with Nylock Nuts but DO NOT TIGHTEN
3. Tighten bolts starting with the center bolt and alternating till all bolts are
tightened down.
ASSEMBLY
D. Cover Assembly
1. Gently place the folded Cover Lift cover on top
of hot tub with the cover’s seam (fold) facing
the control panel so that the ap on the cover is
ush with the edge of the cabinet.
2. Loosen the Lock Knob and pull the extension
Arm to a horizontal position.
3. Using a phillips head screw driver, remove the
screw and nut from the adjustable arm.
4. Now, slide the Extension Arm until it sits
between the fold’s aps along the cover’s fold
seam. (gure 6)
5. Line up the hole in the adjustable arm and
replace the screw and nut.
6. Now, ip the one half of the folded cover over
until it covers the remainder of the hot tub.
7. Take one of the Handle Bars and insert it into
the top of the Molded Saddle, located on the
end of the Extension Bar.
8. Using a 2-1/2” bolt and Nylock Nut, fasten the Handle Bar to the Extension Bar. Be sure to tighten until at
least one thread of the bolt is through the Nylock Nut.
9. Insert the Torsion Bar into squared end of the mounted Handle Bar, then insert the opposite end of the
Torsion Bar into the remaining Handle Bar. Be sure to put equal amounts of the Torsion Bar into each
Handle Bar.
10. Using a 2-1/2” bolt and Nylon Nut, secure the other Handle Bar to the Molded Saddle of the remaining
Extension Arm.
OPERATION
A. Lifting
1. Before lifting the cover, make sure there is nothing on the cover.
2. Look to see that there is no overhead obstruction that could interfere with the covers trajectory (lights, wires,
branches, etc...)
3. To lift the cover, simply grab a hold of either Handle Bar, and lift in an upward motion.
4. The hydraulic arm of the Cover Lift will provide the necessary power to assist in lifting the cover.
5. Bring cover to its ull upright position, the cover will hang slightly toward the hot tub, tighten the lock knob
for extra secure hold of raised cover. Loosen knob to lower and tighten again when closed.
6. The Cover Lift cover provides excellent heat retention when in place, and acts as a sound bafe and privacy
screen when in the lift position.
Phil-Pan Screw
Pivot Bar
Extension Bar
Torsion Bar
1-1/4” Lag
Bolts

HARDWARE CHART
Aluminum Clamp
Phil-Pan Screw
Under Hinge Bar
1-1/4” Lag Bolt
3/4” Hex Bolt
Nylock Nut
Flat
Washer
Handle Bar
Side Mount Brackets
Lock Knob
Spring Washers
Shipping Bolt
Extension BarSafety TieLock Bar
Torsion Bar

5 YEAR LIMITED WARRANTY
SPAccessories warrants this product to be free from defects in workmanship and material, under normal use
and service conditions, for a Limited 5 Year Warranty. This warranty extends only to the original purchaser.
SPAccessories’ obligation under this warranty is limited to replacing or repairing, at SPAccessories’ option,
the product at one of its authorized service centers. All products for which warranty claim is made must be
received by SPAccessories at one of its authorized service centers with all freight and other transportation
charges prepaid, accompanied by sufcient proof of purchase. All returns must be
pre-authorized by SPAccessories. This warranty does not extend to any product or damage to a product
caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not
provided by a SPAccessories authorized service center, products used for commercial or rental purposes,
or products used as store display models. No other warranty beyond that specically set forth above is
authorized by SPAccessories.
SPAccessories is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or damages with respect to any economic loss,
loss of property, loss or revenues or prots, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or tness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specic legal rights. You may also have other rights which vary from state to state.
SPAccessories, 6848 S. Airport Rd., West Jordan, UT 84084
6

S
p
a & Hot Tub Necessities
6848 S. Airport Road ~ West Jordan, UT 84084