Bradley S19-630 User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX [phone]
http://www.bradleycorp.com
Installation
215-085 Rev. K; EN 06-532D
© 2007 Bradley Corporation
Page 1 of 4 4/30/07
S19-630
Hand-Held Eye/Face Body Wash
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . . .2
Installation Instructions . . . . . . . . . . . . . . . . . . .3
Assembly of Components . . . . . . . . . . . . . . . . .4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the
installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to
the eyewash should be “ON” at all times. Provisions shall be made to prevent
unauthorized shutoff.
The ANSI Z358.1 standard requires an uninterruptable supply of flushing fluid at
a minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per
ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to
ensure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment
per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit
www.bradleycorp.com or call 1-800-BRADLEY.
Product warranties may also be found under ”Product Information” on our web
site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
!
!
!
!
P.O.Box309, MenomoneeFalls, WI 53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-051
2
S19-630 Installation
4/30/07 Bradley Corporation • 215-085 Rev. K; EN 06-532D

Installation
Step 1: Install mounting bracket to
wall
NOTE: Make sure that, when mounted, the
eye wash unit will measure 33-45 inches from
the top of the sprayheads to the finished floor.
For usage as an eye/face wash, the top of the
sprayheads of the S19-630 must be 33–45
inches from where the user stands per ANSI
Z358.1. The unit must also be placed a
minimum of 6" away from the nearest wall or
obstruction.
1. Install three suitable wall anchors for use
with 3/8" bolts (supplied by installer) into
the wall at the desired location (see
Figure 1a for eye wash dimensions and
Figure 1b for bracket dimensions).
2. Bolt the mounting bracket to the wall
using three 3/8" bolts (supplied by
installer).
Step 2: Assemble eye/face
body wash unit
1. Assemble the component parts as
shown in Figure 2 on page 4.
• Be sure to apply pipe sealant to
all pipe joints.
Step 3: Connect water supply
1. Connect the water supply to the
unit (piping supplied by
installer).
2. Mount the safety sign to the wall
using the sign-mounting
hardware supplied by installer.
3. Open the water supply line. Test
for leaks and adequate water
flow.
3
Installation S19-630
Bradley Corporation • 215-085 Rev. K; EN 06-532D 4/30/07
10-3/4"
(273mm)
8-3/4"
(222mm)
15"
(381mm)
33-45"
(838-1143mm)
TO FINISHED
FLOOR
Figure 1a
2"
(51mm)
2"
(51mm)
4"
(102mm)
2"
(51mm)
4-3/8"
(111mm)
7/8"
(22mm)
Figure 1b

Assembly of Components and Parts List
4
S19-630 Installation
4/30/07 Bradley Corporation • 215-085 Rev. K; EN 06-532D
1 S05-064D 1 EFW Assembly
1.1 S05-091P 1 Yoke Assembly
1.2 S05-135 2 Sprayhead Assembly
1.3 S53-063 2 Dust Cover
2 113-918 1 Pipe, Plated
3 110-212 2 Nut, Lock
4 141-008 1 Hanger
5 269-1096 1 Handle
6 S30-070 1 Valve/Handle Prepack
6.1 S27-282 1 1/2" Ball Valve with Nut
6.11 110-215 1 Nut only
6.2 142-002DA 1 Lockwasher
6.3 S08-336 1 Handle Assembly
6.4 153-372R 1 Adapter
7 269-053 1 Hose, 12’
8 169-078 1 Adapter
9 S70-094 1 Wall Bracket
10 114-051 1 Safety Sign
11 204-421 1 Emergency Tag
Item Part No. Qty Description Item Part No. Qty Description
94
87
6.2
6.11
6.3
5
2
3
6.1
1.2
1.3
1.1
P.O.BOX309
MENOMONEEFALLS,WI53052-0309USA
TEL:1-800-BRADLEYFA X:(262-251-5817)
http://www.bradleycorp.com
P.O. B OX 309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051
10
P.O. B ox 309, Menomonee Falls, WI 53051
R
TESTTHISUNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctionsimmediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift.Jegliche Störungsofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement desvalveschaque semaine et
signe en bas. S'il y à quelque chose qui ne va pasfait
un rapport immédiatement.
11
1/2" IPS
SUPPLY
INLET
1
6
6.4
Figure 2
NOTE: Items 1–5 come preassembled.
Prepack S30-071 includes Items 6.11, 6.2, 6.3 and 6.4