Speakman RPG05-109305 User manual

INSTRUCTIONS FOR MODELS
92-RPG05-109305-01
For additional assistance or service please contact:
SPEAKMAN®
800-537-2107
customerser[email protected]
www.speakman.com
RPG05-109305
TOOLS AND SUPPLIES
Phillips
Screwdriver
IMPORTANT
• Be sure to read instructions thoroughly before
beginning installation.
• Be sure to have properly adjusted the Temperature
Limiting Stop (TLS) as outlined in this Installation
Manual.
• Inspect all connections of the Valve after installation
of this repair part.
• The Valve installed with this repair part typically has
an operating range of 20-80 Psi.
• The Valve installed with this repair part is designed to
be used in conjunction with a shower-head rated at
1.75 gpm (6.8 L/min) or higher flow rate.
• NOTE: This installation manual covers the steps to
replace the Old Cartridge in several models of
the Shower Valves. While the appearance of your
valve may differ from those shown, the installation
method is the same.
SAFETY TIPS
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
MAINTENANCE
Your Shower/Bath Valve is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of
harsh chemicals and abrasives on any of the
Speakman custom finish products may damage the
finish and void the product warranty. Please be sure
to only use approved cleaners. Please contact
Speakman for any clarification of acceptable
cleaners.
WARRANTY
Warranty information can be found at:
www.speakman.com
1Turn “OFF” water supplies. Remove the Trim (if any) accordingly and keep it aside to reinstall later.
Remove the OLD Cartridge Assembly of the Shower Valve by following the steps below.
• Remove Spindle O-ring ❶, TLS Plate ❷, and four (4) Bonnet Screws ❸.
NOTE: Do not lose the four (4) Bonnet Screws as these will be used to install the new Cartridge
Assembly Kit.
• Then remove Bonnet ❹, Cartridge Assembly ❺, and the O-ring ❻ from Valve Body. Discard
these three (3) items.

2Install the NEW Cartridge Assembly Kit by following the steps below.
• Place the supplied Large O-Ring ❶into the Valve Body.
• Install the Cartridge Assembly ❷into the Adapter ❸.
NOTE: If you are performing a Back-to-Back Installation or have Reversed Inlet supplies, rotate the Cartridge ❷180°. The “H” marking on the Cartridge cover should now be on the right hand side.
• Verify the two (2) Lower Seals ❹supplied with this Kit are fully seated within the Adapter ❸.
• Slide the Bonnet ❺onto the Cartridge ❷. Install with the word "UP" facing upward ❺.
• Install the Cartridge Assembly to the Valve Body using the four (4) Bonnet Screws ❻ from the existing Shower Valve.
ROTATE 180˚ FOR
BACK-TO-BACK
MOUNTING OR
REVERSED INLETS
3Ensure the Valve is in the “OFF” position. Turn “ON” water supplies and check all connections
for leaks. Proceed to Step 4 for any temperature limit adjustment prior to reinstalling the Trim
(if any) accordingly.
LUG
TLS PLATE
O-RING
The maximum outlet temperature setting adjustment [Temperature Limit Stop (TLS)] of the Valve has been
factory set at 110° F. To adjust the limit of the maximum outlet temperature the Valve delivers, adjust
the Valve’s temperature limit stop (TLS) Plate.
• Slip the retaining O-ring and the TLS plate
towards the end of the spindle.
• With the water supplies “On”, rotate the
valve spindle clockwise to the maximum
desired hot water temperature.
• Position the TLS plate so it contacts the Lug
and therefore restricts the clockwise rotation
of the spindle.
• Slip the retaining O-ring back into the
groove of the spindle to hold the TLS plate in
place.
• Rotate the spindle counter-clockwise to the
“Off” position.
TEMPERATURE LIMIT ADJUSTMENT4
NOTE: A thermometer can be held at the Valve outlet to aid in either checking the existing factory setting
or reaching the desired outlet temperature.