Speakman EYESAVER SE-460 User manual

SPEAKMAN COMPANY
SE-460 Installation, Maintenance & Operation Instructions
EYESAVER®EYE/FACE WASH
DESCRIPTION
Emergency eye/face wash supplied with stainless steel bowl, stay-open full flow ball valve; activated by stainless steel push
handle; in-line strainer, and mounted on countertops up to 1-1/2” thick. Spray pattern is a 9” x 8” (72 sq. in.) curtain of aerated
water, easily controlled at any pressure for maximum protection.
SPECIFICATIONS
BOWL: 300 Series Stainless Steel. (Reference additional SE-300 I,M,O sheet)
SPRAY HEADS: (6) Brass, Chrome-Plated, Aerated.
VALVE: 1/2” NPT Female Brass, Chrome-Plated.
ACTIVATOR: Stainless Steel Push Handle.
SHROUDS: Yellow Polypropylene.
INLET: 1/2” NPT Female.
STRAINER: Brass, Chrome-Plated, In-Line.
SHIPPING WEIGHT: 18 lb.
EMERGENCY SIGN: 7-7/8” x 7-7/8” Plastic Wall Sign.
OPTIONS
INSTALLATION
Use cutting/drilling instruction template (supplied) to cut and drill holes in desired location on countertop. Once bowl is
mounted securely to countertop, complete assembly of ball valve and push handle. Review drawing (as shown on other side)
to assure proper installation. Be sure to apply a bead of waterproof caulk along edge of bowl and countertop to prevent water
draining under countertop. Connect a water supply to the unit (use pipe sealant on all joints) that is a 1/2” minimum
uninterrupted source of potable water. Failure to use potable water can result in emergency units producing impure or
contaminated water causing possible further injury. The drain tailpiece or waste should be connected to an adequate drain in
compliance with local plumbing codes. Once water supply is connected to unit the spray pattern can be manually adjusted by
using a flat head screw driver to rotate the adjusting screw, located in the front of each shroud assembly, while the unit is
activated and water is flowing.
OPERATION
The eye/face wash is activated by pushing the push handle back 90°. The unit will continue to operate until the push handle is
manually pulled back to the off position.
TESTING PROGRAM
The American National Standards Institute (ANSI) states that all safety emergency equipment
shall be activated on a weekly basis to flush the line and verify proper operation. Speakman
Company furnishes a testing record tag (91-0635) with each unit. On this tag the date of
inspection and the inspectors initials should be noted.
◊ AL1 (Air Horn Alarm) ◊ FPV (Anti-Freeze Protection Valve)
◊ AL2 (Electrical Alarm) ◊ SGN4 (Eye Wash Floor Sign)
◊ AL3 (Electrical Alarm) ◊ SPV (Anti-Scald Protection Valve)
◊ AL2-C1D2 (Electrical Alarm / Haz. Area) ◊ SSBV2 (1/2” Stainless Steel Valve)
◊ AL3-C1D2 (Electrical Alarm / Haz. Area) ◊ VPL (Vapor Proof Light)
◊ FLW (Flow Switch) ◊ PT (1-1/4” P-Trap)
MAINTENANCE
Should you need parts to repair
this unit, please reference the
parts list below for correct part
numbers. Before any
maintenance is done be sure to
s
hut the water supply off.

12/05
92-1426 Rev-5
SE-460 REPLACEMENT/REPAIR PARTS
ITEM PART/GROUP # DESCRIPTION
1 20-0953 1/2” Ball Valve Brass RNP
2 68-0033-MO S/S Bowl
3 04-0523 Push Handle
4 G10-0042-RCP Shroud Assy.
5 03-0520 Spindle Extension
6 G21-0082-PC-P In-Line Strainer
7 92-0034 Template (Not Shown)
FLOW DATA
EYE/FACE WASH:
NOTE: This unit should be connected to an uninterrupted source of potable water, with a minimum flowing
pressure of 20 PSI and a maximum static pressure of 125 PSI.
Note: All units meet existing
ANSI Z358.1 Standards and
OSHA Rules. Product
improvements may cause
specification and dimensional
changes without notice.
FLOW PRESSURE PSI (BAR) 30 (2.07)
FLOW RATE GPM (LPM) 9.55 (16.6)
WARNING: Use only
g
enuine Speakman parts when
repairing or replacing
components.
To order parts call 1-800-537-
2107.