Speco O4P25X User manual

Quick Start Guide
O4P25X

Welcome
Thank you for purchasing this PTZ camera!
This owner's manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, contact Speco Technologies Tech Support at
1-800-645-5516
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 24VDC/AC power supply only.
Please note: Do not connect two power supplying sources to the device at the same time;
it may result in device damage! The product must be grounded to reduce the risk of
electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation,
storage and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat
sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS
sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
Important Safeguards and Warning

Warning
Statement
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
.
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring
any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is
broken or missing in the package.
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.

Overview
3 Overview
1
①LAN
②3.5mm Audio Out
③3.5mm MIC In
④Alarm I n /Alarm Out
⑤Power
1
2
3
4
5
Note: DC24V and AC24V power supply
are optional.
Installation
2
◆Install SD Card
Please make sure the wall is strong enough to bear the dome
camera’s weight. Please make sure the camera is powered off
during installation.

① Loosen the two screws of the dome. ② Open the cover and insert SD card.
Insert SD card
◆Install the Speed Dome
③ Drill the screw holes on the wall according
to the drill template. Then insert the plastic
plugs into the holes.
④ Drive the two screws to the holes indicated
by the arrows (left) and leave 12mm
clearance.
① Pull the cables through the bracket. Mount the
speed dome to the bracket.
② Secure the speed dome to the bracket with
the screws.

⑤ Connect the cables and then hang the
bracket on the wall .
⑥ Fasten the bracket to the wall with
four screws.
Cable Connection
3
HP Audio Out
Network Port
MIC IN
Power
ALM-OPEN
ALM-COM
ALM-GND
ALM-IN1
24V A
24V B
Earth
DC24V
AC24V

Alarm Connection:
1. Alarm Input
a) There is one independent alarm input port (ALM-IN1) and
one grounding port (ALM-GND).
b)Alarm input(NO type): Connect DC5V~DC12V voltage
between the alarm input port( ALM-IN1) and the grounding port
(ALM-GND).
c) Alarm input(NC type): Disconnect the voltage between the
alarm input port(ALM-IN1) and the grounding port (ALM-GND).
2. Alarm Output
a) Support 1CH alarm output including OPEN, COM
connections.
b) Alarm output: One passive switch for user to connect alarm
devices; the alarm output state will be auto on/off according to
your setting.
Web Operation and Login
4
●Operation
IP Scanner can search for the device on the local network.
①Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
②Install IP Scanner from the CD and run it after installation.

③In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser (Internet Explorer 8 and up).
5C :F2:0 7: 24:68 :B9
O4 P25X
The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins.