Speco O6FB7M User manual

Flexible Intensifier® Technology Bullet IP Camera
QUICK INSTALLATION GUIDE
O6FB7M
Please read this manual carefully before installation and operation of the product.

1
Notice
Thank you for purchasing this product. This guide is designed to be a reference tool for the product. Please read
it carefully before operating the product and retain it for future reference. Should you require any technical
assistance, please contact Speco Technologies Technical Support.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at its own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority
to operate the equipment.
CAUTION –To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to all local codes.
The lighting flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of non-insulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION

2
PRECAUTIONS
Please read the manual carefully before the installation in order to set up the camera correctly and
to obtain the best picture quality.
Please keep the manual in good condition for your future reference and service application.
Installation and services should only be carried out by an authorized personnel according to local
safety regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power
supply and have it checked by your authorized dealer before reusing.
Avoid installing the camera at extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside that need
maintenance by the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at the place exposed to gas or oil.
Keep the top glass of the lens always clean in order to obtain the best picture quality all the time.
Be careful not to be stained by fingerprint.
Don't face the camera directly toward sunlight or sunlight reflecting area.
IMAGE SENSOR may go defective at this condition.
Please give a special attention to keep the unit from dangerous drop or external shock during the
process of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock.
Do not expose the camera to radioactivity. It causes a serious damage on the IMAGE SENSOR.
LIMITATION OF LIABILITY
This publication is provided “AS IS” without warranty of any kind, either express or implied, including
but not limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-
infringement of the third party's right.
This publication could include technical inaccuracies or typographical errors. Changes are added to
the information herein, at any time, for the improvements of this publication and / or the corresponding
product(s).
DISCLAIMER OF WARRANTY
In no event shall seller be liable to any party or any person, except for replacement or reasonable
maintenance of the product, for the cases, including but not limited to below :
(1) Any damage and loss, including without limitation, direct or indirect, special, consequential or
exemplary, arising out of or relating to the product.
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user.
(3) Unauthorized disassemble, repair or modification of the product by the user.
(4) Inconvenience or any loss arising when images are not displayed, due to any reason or cause
including any failure or problem of the product.
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the system
combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being photogenic subject,
due to violation of privacy with the result of that surveillance-camera's or video server’s picture,
including saved data, for some reason, becomes public or is used for the purpose other than
surveillance.

3
1. PRODUCT OVERVIEW
Key Features
6.82 Mega pixel 1/2.9" SONY progressive scan CMOS image sensor for excellent image quality
IP67 rated water-proof
Triple Streaming of H.265, H.264 and M-JPEG
Supports image resolutions 6M (3072 x 2048)
Integrated motion detection with pre- and post-alarm image / video buffering
Supports CBR (Constant Bit Rate) and VBR (Variable Bit Rate) modes
Supports Tampering-Alarm in VA (Video Analytics) function
Controllable frame rate
Full Duplex Two-Way Audio Support
External Audio Line-input & Audio Line-output connector
External sensors or external alarm devices
Privacy Masking
Supports IEEE 802.3af Power over Ethernet injectors, mid- and end-spans
HTTPS supported (Hyper Text Transfer Protocol Secured)
Integrated E-Mail, FTP, DDNS and DHCP client
Specification
CLASSIFICATION
Night Vision Bullet IR Camera
General
CPU
ARM Cortex-A9 816MHz CPU with L2 cache
Flash
2Gbit Flash Memory
SDRAM
8Gbit DDR3 Memory
Image Pickup
Image Sensor
6.82 Mega 1/2.9" SONY STARVIS image sensor
Total Pixels
3096(H) x 2218(V) 6.87 Megapixel
Effective Pixels
3096(H) x 2202(V) 6.82 Megapixel
S/N Ratio
More than 50dB
Min. Illumination
0Lux (IR On)
IR Distance
40M
Day & Night
Auto, Color, BW
Lens
2.7 ~ 12mm Vari-focal Motorized Megapixel Lens
Video
Video Compression
H.265 / HEVC Main Profile Level 5.1 encoding
H.264 High profile @ Level 5.1 MJPEG
Resolutions
Up to 3072 x 2048 @ 20fps
Frame Rate
H.265 / H.264 Up to 20fps with 3072 x 2048,
H.265 / H.264 Up to 15fps with 640 x 360
H.264 / MJPEG Up to 5fps with 640 x 360
Video Streaming
Support multi stream with H.265 / H.264,
Adjustable frame rate, VBR / CBR
Image Setting
Brightness, Contrast, Sharpness
Day & Night, Auto White Balance, Auto Exposure
Privacy Mask
DSS, 3DNR
V-Flip, etc.
WDR, ATR
Video Output
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC / PAL
Audio
Audio Streaming
Two-way, full duplex
Audio Compression
G.711
Data / Sample Rate
64Kbps / 8KHz
Audio Input / Output
Microphone input / 1x Line-In, Line-Output / 1x Line-Out
Network
Security
Password protection, User access log, HTTPS encryption
Supported Protocol
HTTP, HTTPS, DNS, RTSP, RTP, TCP, UDP, ICMP, DHCP

4
System
Integration
Intelligent Video
Motion detection (4 Separate blocks)
Alarm Trigger
Motion Detection
Firmware Upgrade
Remote Upgrade via Network
Physical
Etc
1 x Factory Reset Button
Memory Slot
Micro SD card
Power Source
DC 12V / 1.5A, POE (Power Over Ethernet) : 802.3af
Power Consumption
Max.7.2W (IR ON)
Net Weight
1060g (Camera Only)
State LED's
Power, Network Connection
Dimension(mm)
Ø98.5 x 262.5 Including Bracket
Environment
Operating
Temperature
-40 degree ~ 60 degree Celsius (-40F ~ 140F)
Storage
Temperature
-20 degree ~ 60 degree Celsius (-4F ~ 140F)
※Specifications are subject to change without prior notice for improvement.
2. NAME AND FUNCTION OF EACH PART
2.1 Package Contents
APPEARANCE DESCRIPTION
IP Camera x 1
Installation Guide x 1
Tapping screw (Ø4 x 30) x 4
Plastic anchor x 4
L-Wrench (4mm) x 1
L-Wrench (2.5mm) x 1
CD x 1
Junction Box
Top Rubber x 1
Junction Box x 1
Sponge x 1
Tapping Screws (Ø4 x 30) x 4
Plastic Anchor x 4
Screw PH (M4 x 12) x 4

5
2.2 Name and Function
NO.
ITEM
DESCRIPTION
BNC
Analog Video Out (Yellow)
Power Connector
DC12V
Network and POE
Connector
POE (Power Over Ethernet) and LAN cable
Sensor In / Alarm Out
Sensor Input : White (Sensor_In), Yellow (GND)
Alarm Output : Black (Alarm_Out), Red (COM)
Audio-Out
Audio Out (White)
Audio-In
Audio in (Red)
Lens
2.7 ~ 12mm Vari-focal Motorized Megapixel Lens
IR LED
Infrared Hi-power LED
Heater
Resistors reduce condensation on front glass
Illumination sensor
Control IR LED by sensing light
7
8
10
9
1
2
3
4
5
6
1
2
7
3
4
5
6
8
9
10

6
2.3 OSD cap detailed description
Open the Closing Cap and fasten the Closing Cap well.
3. INSTALLATION
3.1 How to mount to wall
Wall_Junction Box
Wall
①Drill four screw holes on the wall plate to fix four plastic anchors (supplied) in the holes.
②Fix the plastic anchors in the holes.
③Position the bracket on the screw points.
④Fix the bracket by tightening the screws.
Tapping screw
(Ø4 x 30) x 4
Plastic anchor
x 4
Screw x 4
Closing Cap
SD Card
Factory Reset
CVBS
L-Wrench (2.5mm)
Closing Cap Open

7
3.2 3-Axis Adjustment
①Panning 360˚
Slightly loosen Pan Bracket nut then
adjust pan of the camera and
tighten the Bracket nut.
②Tilt 0˚ ~ 100˚
Slightly loosen Tilt bolt then
adjust tilt of the camera and
tighten the bolt firmly.
③Rotation 360˚
Slightly loosen Tilt bolt then adjust rotation of the camera
and tighten the bolt firmly.
3.3 Installation Example
3.3.1 Installation Example
LAN Switch Router Internet Remote Access
Local Access E-Mail / FTP
Rotation
360°
Tilt
0°100°
Panning
360°
Rotation
Tilt
Pan
L-Wrench

8
3.3.2 Connecting Network
Open up IP Scanner.
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
The device is set to DHCP mode by default.
In the device list, you can view the IP address, model number, and MAC address of each device. Select the
applicable device and double click to open up the web viewer.
3.3.3 Accessing the Camera or video server’s Homepage
1) Open the browser and enter the camera’s IP address in the address bar or double click the device in IP
Scanner.
2) Enter the user name and password when prompted.
3) Default user name is admin and password is 1234.
4) If prompted for installation of the Active-X plug-in, allow the installation. Active-X is needed to view video
from Internet Explorer.
Enter the IP
address here

9
4. DIMENSIONS (mm)