Speco O2VLB8 User manual

User Manual
2MP IP Camera
O2VLB7 / O2VLB8 / O2VLD7 / O2VLD7J/ O2VLD8
Please read this manual carefully before operating the unit and keep it for further reference

IP Camera User Manual
Important Safeguards and Warnings
1．
．．
．Electrical safety
ll installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to t e device at t e same time; it may result in device damage! T e
product must be grounded to reduce t e risk of electric s ock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2．
．．
．Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.
lways use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small quantity of neutral
detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may result
in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation and use, please refer to the
following methods if dirt is found:
Stained with dirt
Use oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint
Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and wipe
several times if it is not clean enough.

IP Camera User Manual
Warning
This camera should be installed by qualified personnel only.
ll the examination and repair work should be done by qualified personnel.
ny unauthorized changes or modifications could void the warranty.
Statement
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the right to modify these
without notice and without incurring any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Regulatory Information
1.1 FCC conditions ：
：：
：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation.
1.2 FCC compliance ：
：：
：
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference. This equipment generate, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the package.
ccessory Name mount
Network Camera Unit 1
Quick Start Guide 1
Installation ccessories Bag 1
CD 1

IP Camera User Manual
Table of Contents
Regulatory Information ...................................................................................................................................................................................... 3
1 Introduction ................................................................................................................................................................................................ 1
Welcome.............................................................................................................................................................................................................. 1
2 Web Access and Login .............................................................................................................................................................................. 2
2.1 LAN........................................................................................................................................................................................................................................ 2
3 Live View ..................................................................................................................................................................................................... 3
4 Camera Configuration................................................................................................................................................................................ 4
4.1 System Configuration ............................................................................................................................................................................................................. 4
4.1.1 System Information ................................................................................................................................................................................................. 4
4.1.2 Date and Time......................................................................................................................................................................................................... 4
4.1.3 Users ...................................................................................................................................................................................................................... 5
4.2 Display Configuration.............................................................................................................................................................................................................. 5
4.2.1 OSD........................................................................................................................................................................................................................ 5
4.2.2 Image Configuration ................................................................................................................................................................................................ 6
4.2.3 Privacy Mask........................................................................................................................................................................................................... 6
4.2.4 Video Stream Setup ................................................................................................................................................................................................ 7
4.2.5 Path (Local Recording)............................................................................................................................................................................................ 7
4.3 Network Setup........................................................................................................................................................................................................................ 8
4.3.1 Network................................................................................................................................................................................................................... 8
4.3.2 Email....................................................................................................................................................................................................................... 8
4.3.3 DDNS...................................................................................................................................................................................................................... 9
4.3.4 IP Filter ................................................................................................................................................................................................................... 9
4.3.5 RTSP .................................................................................................................................................................................................................... 10
4.3.6 FTP....................................................................................................................................................................................................................... 10
4.3.7 SNMP ....................................................................................................................................................................................................................11
4.4 Motion Setup ........................................................................................................................................................................................................................ 12
4.4.1 Motion Detection ................................................................................................................................................................................................... 12
4.5 Device Log ........................................................................................................................................................................................................................... 12
4.5.1 Log........................................................................................................................................................................................................................ 12
4.6 Advanced Configuration........................................................................................................................................................................................................ 13
4.6.1 Firmware Update................................................................................................................................................................................................... 13
4.6.2 Factory Default...................................................................................................................................................................................................... 13
4.6.3 Auto Reboot .......................................................................................................................................................................................................... 13
Appendix ........................................................................................................................................................................................................... 14
Appendix 1 Troubleshooting ........................................................................................................................................................................... 14

1
IP
Camera User Manual
1Introduction
Welcome
Thank you for purchasing this network camera!
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support.
Main Features
Built-in PoE (Power over Ethernet)
Integrated IR LEDs for clear vision in low light
IP66 rated for outdoor installations
Remote viewing support via web browser, mobile app, and VMS

2
IP
Camera User Manual
2Web Access and Login
The IP camera settings can be accessed via a
web browser through the L N
2.1 LAN
ccess through IP Scanner
Network connection:
① Make sure
that the camera and the PC are connected
address by the DHCP server. Make sure that the local network has a DHCP server. Routers typically have a DHCP server built in
②
Install IP Scanner from the CD and run it after installation.
③
In the device list, the IP address, model number, and M C address of each device
up
the web viewer. You can also manually enter the IP address in the address bar of the web browser.
The login interface is shown above. Default user name is admin and password is 1234. fter logging in, follow directions to i
viewing video.
web browser through the L N
.
that the camera and the PC are connected
on the same local network. The camera is set to
DHCP by default and will be assigned an IP
address by the DHCP server. Make sure that the local network has a DHCP server. Routers typically have a DHCP server built in
Install IP Scanner from the CD and run it after installation.
IP Scanner is the tool for discovering the IP cameras on the local network.
In the device list, the IP address, model number, and M C address of each device
will be listed
. Select the applicable device and double click to open
the web viewer. You can also manually enter the IP address in the address bar of the web browser.
The login interface is shown above. Default user name is admin and password is 1234. fter logging in, follow directions to i
DHCP by default and will be assigned an IP
address by the DHCP server. Make sure that the local network has a DHCP server. Routers typically have a DHCP server built in
.
IP Scanner is the tool for discovering the IP cameras on the local network.
. Select the applicable device and double click to open
The login interface is shown above. Default user name is admin and password is 1234. fter logging in, follow directions to i
nstall applicable plug-ins for

3
IP
Camera User Manual
3Live View
The window below will be shown after logging in.
The following table describes the icons on the live view
Icon
Description
Go to camera setup
Stop/Start
View in stretched format
Start local recording
Digital zoom
 In full scr
een mode, to exit, double click on the mouse or press the ESC key on the keyboard
live view
interface.
Description
Icon Description
Go to camera setup
djust image settings
Stop/Start
live view View in original aspect ratio
View in stretched format
View in full screen
Start local recording
Generate snapshot
Digital zoom
een mode, to exit, double click on the mouse or press the ESC key on the keyboard
.

4
IP
Camera User Manual
4Camera Configuration
Press the “Setup” button to go to the
configuration interface.
Note: Wherever applicable, press the “Save” button t
o save
4.1 System Configuration
4.1.1 System Information
In the “System Information” interface, the system
information of the
4.1.2 Date and Time
To set the time and date, go to SystemGeneral
. Please refer to the following interface.
Select an option to set the time and date.
DST: If daylight saving time is utilized in the current time
NTP: If enabled, the device will synchronize the time with a time server. Select the applicable time zone before synchronizat
Synchronize: Sets the device time same as the PC.
configuration interface.
o save
the settings.
information of the
device is listed.
. Please refer to the following interface.
DST: If daylight saving time is utilized in the current time
zone, use this option to set the parameters.
NTP: If enabled, the device will synchronize the time with a time server. Select the applicable time zone before synchronizat
NTP: If enabled, the device will synchronize the time with a time server. Select the applicable time zone before synchronizat
ion.

5
IP
Camera User Manual
4.1.3 Users
To configure users, go to System -> Users.
Other than admin, up to 6 additional users can be configured, with customizable access levels.
4.2 Display Configuration
Display Configuration includes Image settings, Stream
Setup
4.2.1 OSD
Go to DisplayLive as shown below.
North merica uses 60Hz for flicker control. Enable Name and Time to show the camera name and time on the screen. C
the settings.
Other than admin, up to 6 additional users can be configured, with customizable access levels.
Setup
, OSD, Privacy Mask, and local recording path setup.
North merica uses 60Hz for flicker control. Enable Name and Time to show the camera name and time on the screen. C
Other than admin, up to 6 additional users can be configured, with customizable access levels.
North merica uses 60Hz for flicker control. Enable Name and Time to show the camera name and time on the screen. C
lick the “Save” button to save

6
IP
Camera User Manual
4.2.2 Image Configuration
In the Image Control interface shown below
, various settings can be adjusted such as
IR-Cut Mode:
Choose between uto, Color Mode, and monochrome Mode
IR-Cut Delay:
Sets the delay in how long the camera waits before switching to color or
mode is set to uto.
Lens Flip / Angle Flip: Horizontal and vertical flip.
Backlig t Compensation (BLC)
: if enabled, the auto exposure will activate according to the scene so that the object of
be seen clearly.
3D Noise Reduction: Digital noise reduction.
WDR:
Compensates for a contrast in the scene between light and dark areas.
entrance.
AGC: Gain control.
W ite Balance:
djust the color temperature according
S utter:
Choose between auto shutter speed and manual.
Time Exposure:
Use for manual shutter speed adjustment
Infrared Mode: Choose “ON”, “OFF” or “ uto”.
Defog Mode: Digital defog.
Used to try to clear up a foggy image.
4.2.3 Privacy Mask
Go to the DisplayPrivacy Zone interface
shown below.
To set up privacy mask zones:
1. Click Enable.
2. Within the image window,
drag the mouse to draw the zones.
3. Click the “Save” button to save the settings.
To clear the
privacy mask zones, click to choose each zone and click the “Delete” button.
, various settings can be adjusted such as
brightness, contrast, hue,
saturation
Choose between uto, Color Mode, and monochrome Mode
.
Sets the delay in how long the camera waits before switching to color or
monochrome when light level changes
: if enabled, the auto exposure will activate according to the scene so that the object of
Compensates for a contrast in the scene between light and dark areas.
Typically used in a lobby where the camera is pointing towards the
djust the color temperature according
to the environment.
Choose between auto shutter speed and manual.
Use for manual shutter speed adjustment
.
Used to try to clear up a foggy image.
shown below.
maximum of 4 zones can be set up.
drag the mouse to draw the zones.
privacy mask zones, click to choose each zone and click the “Delete” button.
saturation
, etc.
monochrome when light level changes
. This applies when the
: if enabled, the auto exposure will activate according to the scene so that the object of
the image in the darkest area will
Typically used in a lobby where the camera is pointing towards the

7
IP
Camera User Manual
4.2.4 Video Stream Setup
Go to DisplayVideo Streaming as shown below. R
esolution, frame rate,
Two video streams can be adjustable.
Resolution: The size of the image.
FPS (frame rate): The higher the frame rate,
the video is smoother
Video Code Type: Choose between H.264 and H.265.
If H.265 is chosen, make sure the client system is able to decode H.265.
Video Code Level (Profile):
For H.264. Choose between b
Bitrate Control: Options are CBR (constant) and VBR
(variable)
seen in the video scene, the compression bitrate
will be kept
changes. For example, f
or scenes that do not have much movement, the bitrate will be kept at a lower value.
bandwidth usage.
Bitrate Mode:
If Predefined is chosen, the bitrate value is set to a reference value based on the resolution
Bitrate:
The higher the bitrate, the better the image quality will be.
I Frame Interval:
Group of pictures. Determines how many frames are allowed between a “group of pictures”
that scene ends, the entire group of frames (
or pictures) can be a considered a GOP. If there is not much movement in the scene, setting a GOP value
higher than the frame rate is fine, potentially resulting in less bandwidth usage. However, if the value is set too high, and
movement in the video, there is a risk of frame skipping.
4.2.5 Pat (Local Recording)
Go to DisplayPath
to set up the storage path of captured images and recorded video on the local PC
esolution, frame rate,
etc. can be adjusted in this section.
the video is smoother
.
If H.265 is chosen, make sure the client system is able to decode H.265.
For H.264. Choose between b
aseline, main, and high profiles.
(variable)
. Bitrate is related to the image quality.
CBR means that no matter how
will be kept
constant. VBR means that the compression bitrate
will be adjusted
or scenes that do not have much movement, the bitrate will be kept at a lower value.
This
If Predefined is chosen, the bitrate value is set to a reference value based on the resolution
.
The higher the bitrate, the better the image quality will be.
Group of pictures. Determines how many frames are allowed between a “group of pictures”
. When a new scene begins in a video, until
or pictures) can be a considered a GOP. If there is not much movement in the scene, setting a GOP value
higher than the frame rate is fine, potentially resulting in less bandwidth usage. However, if the value is set too high, and
movement in the video, there is a risk of frame skipping.
to set up the storage path of captured images and recorded video on the local PC
.
If H.265 is chosen, make sure the client system is able to decode H.265.
CBR means that no matter how
much change is
will be adjusted
according to scene
This
can help optimize the network
. When a new scene begins in a video, until
or pictures) can be a considered a GOP. If there is not much movement in the scene, setting a GOP value
higher than the frame rate is fine, potentially resulting in less bandwidth usage. However, if the value is set too high, and
there is a high frequency of

8
IP
Camera User Manual
4.3 Network Setup
4.3.1 Network
Go to the NetworkNetwork interface shown below.
Type: Choose between DHCP and Static.
The device will be configured to DHCP by default. If set to static, enter the network info values in the fields.
Ports: Choose port values as desired.
UPNP: If UPnP is allowed and enabled
in the network, enable this option to try to open the ports automatically.
4.3.2 Email
In order to have an email be sent when an event occurs, the email section must be configured first
Go to Network Email.
Encryption: Choose between Disable, SSL, TLS,
or uto based on the encryption method used by the email service provider
SMTP Port:
Enter the SMTP port used by the email provider.
SMTP Server: Enter the SMTP server address.
User Name:
Enter the user name of the sender’s email account.
The device will be configured to DHCP by default. If set to static, enter the network info values in the fields.
in the network, enable this option to try to open the ports automatically.
In order to have an email be sent when an event occurs, the email section must be configured first
.
or uto based on the encryption method used by the email service provider
Enter the SMTP port used by the email provider.
Enter the user name of the sender’s email account.
The device will be configured to DHCP by default. If set to static, enter the network info values in the fields.
or uto based on the encryption method used by the email service provider
.

9
IP
Camera User Manual
Password: Enter
the password of the sender’s email account.
Sender:
Enter the sender’s email address as it would appear in the email.
Receiver 1/2/3:
Enter up to 3 receiving email addresses
Interval: Time interval between sending emails.
For example, if the interval is set to 3 minutes, but there are multiple motion events that occur within
the 3 minutes, the device will still wait the 3 minutes before sending another email.
4.3.3 DDNS
DDNS can
be set for accessing the camera from the internet
1. Go to Network->DDNS.
2. Enable DDNS.
3. Select SPECO as the server.
4.
The hostname will be in this format, SPECOxxyyzz, where xxyyzz is the last 6 digits of the device Mac address.
5.
Click Save. This must be done before testing the DDNS connection.
6. Click Test
DDNS to make sure that the connection was established properly.
4.3.4 IP Filter
Go to NetworkIP Filter as shown below.
Filtering mode: Three modes are available –
allow all connection, allow only IP connections that are set up, and deny IP connections that are set up.
fter choosing the mode, add or remove IP addresses.
the password of the sender’s email account.
Enter the sender’s email address as it would appear in the email.
Enter up to 3 receiving email addresses
.
For example, if the interval is set to 3 minutes, but there are multiple motion events that occur within
the 3 minutes, the device will still wait the 3 minutes before sending another email.
be set for accessing the camera from the internet
.
The hostname will be in this format, SPECOxxyyzz, where xxyyzz is the last 6 digits of the device Mac address.
Click Save. This must be done before testing the DDNS connection.
DDNS to make sure that the connection was established properly.
allow all connection, allow only IP connections that are set up, and deny IP connections that are set up.
For example, if the interval is set to 3 minutes, but there are multiple motion events that occur within
The hostname will be in this format, SPECOxxyyzz, where xxyyzz is the last 6 digits of the device Mac address.
allow all connection, allow only IP connections that are set up, and deny IP connections that are set up.

10
IP
Camera User Manual
4.3.5 RTSP
Go to Network->RTSP as shown below.
Select “Enable” to enable the RTSP function.
Note that RTSP streaming is used to stream the video to the NVR, so it is highly recommended to leave this
enabled.
Port: ccess port of the streaming media. The default
port
RTSP URL: The RTSP address format
that can be used to play
If “ llow anonymous login” is checked
, there is no need
4.3.6 FTP
fter an FTP server is set up, captured images
from events
Go to the Network->FTP.
Server: The IP address or domain name of the FTP.
Port: Port of the FTP server.
User Name and Password
: The username and password
Transfer Images:
Check this option to transfer images to the FTP server.
Note that RTSP streaming is used to stream the video to the NVR, so it is highly recommended to leave this
port
is 9008.
that can be used to play
the stream in a media player.
, there is no need
to enter the username and password to view the video.
from events
will be uploaded to the FTP server.
: The username and password
that are used to login to the FTP server.
Check this option to transfer images to the FTP server.
Note that RTSP streaming is used to stream the video to the NVR, so it is highly recommended to leave this

11
IP
Camera User Manual
4.3.7 SNMP
To get camera status, parameters and alarm information and remotely manage the camera, the SNMP function
install an SNMP management tool and set the para
meters of SNMP, such as SNMP port, trap address.
1. Go to the SNMP section.
2. Select the appropriate version (v1, v2c
, v3) according to the version of the SNMP software that will be used.
3.
Set the values for “Read SNMP Community”, “Write SNMP Community”, “Trap
are the same as that of the SNMP software.
To get camera status, parameters and alarm information and remotely manage the camera, the SNMP function
can be used
meters of SNMP, such as SNMP port, trap address.
, v3) according to the version of the SNMP software that will be used.
Set the values for “Read SNMP Community”, “Write SNMP Community”, “Trap
ddress”, “Trap Port” and so on. Please make sure the settings
can be used
. Before using SNMP, please
, v3) according to the version of the SNMP software that will be used.
ddress”, “Trap Port” and so on. Please make sure the settings

12
IP
Camera User Manual
4.4 Motion Setup
4.4.1 Motion Detection
Go to larmMotion to set up motion detection.
Check “Enable” to activate motion based alarms. If
the NVR or the VMS, even if there is motion in the video.
Sensitivity:
Higher sensitivity value means that motion will be triggered more easily
Send Email: If selected, the system will
capture
the Email section.
To set the motion detection area
, click and drag the mouse to define the region as desired in the image wi
4.5 Device Log
4.5.1 Log
Go to DeviceLog.
There are 6 different log options available: System, Config, larm, User, Network, and ll. Choose the log type, the starting
and the end time for log retrieval. Click on Search to retrieve the list of logs.
Check “Enable” to activate motion based alarms. If
unchecked, the camera will not send out any signals to trigger motion
the NVR or the VMS, even if there is motion in the video.
Higher sensitivity value means that motion will be triggered more easily
.
capture
images on motion detection and
email the images to the email address(es) that were set up in
, click and drag the mouse to define the region as desired in the image wi
ndow.
There are 6 different log options available: System, Config, larm, User, Network, and ll. Choose the log type, the starting
and the end time for log retrieval. Click on Search to retrieve the list of logs.
unchecked, the camera will not send out any signals to trigger motion
-based recording to
email the images to the email address(es) that were set up in
ndow.
There are 6 different log options available: System, Config, larm, User, Network, and ll. Choose the log type, the starting
time,

13
IP
Camera User Manual
4.6 Advanced Configuration
4.6.1 Firmware Update
Go to dvancedFirmware Update. In this interface,
the camera firmware can be updated
1. Click the “Scan
” button to select the location of the firmware file.
2. Click the “Start
” button to start upgrading the
3. The device will restart automatically.
Caution!
Do not close the browser or disconnect the camera from the network during the upgrade
4.6.2 Factory Default
Go to dvancedLoad Default.
 Factory Default
Check the relevant options and click Save to
restore the device settings to factory default
4.6.3 Auto Reboot
Go to dvancedMaintain.
Click the “Reboot” button to manually
reboot the device.
Timed Reboot Setting:
If desired, the camera can be set up to reboot on a time interval.
save the settings.
the camera firmware can be updated
.
” button to select the location of the firmware file.
” button to start upgrading the
firmware.
Do not close the browser or disconnect the camera from the network during the upgrade
.
restore the device settings to factory default
.
reboot the device.
If desired, the camera can be set up to reboot on a time interval.
Enabled “ uto
Reboot” and then set the interval and time.
Reboot” and then set the interval and time.
Click the “Save” button to

14
IP
Camera User Manual
Appendix
Appendix 1 Troubles ooting
IP Scanner does not s ow any device.
Make sure that the PC that’s running IP Scanner is on the same local network as the devices.
Internet Explorer cannot download ActiveX control.
IE browser may be set up to block ctiveX. Follow the steps below.
1. Open IE browser and then click Tools->Internet Options
2. Select Security and then Custom Level
3. Enable all the options under “ ctiveX controls and plug-ins”.
4. Click OK to finish setup.