Speco VLBT5W User manual

User Manual
Thank you for purchasing our product. Speco Technologies is constantly developing and
improving products. We reserve the right to modify product design and specifications
without notice and without incurring any obligation.
VLBT5W /VLBT6W/
VLDT5W/VLDT6M/VLT7W

Warnings
■
Speco Technologies is not responsible for any problems caused by improper operation or repair.
■
■ All installation and operation here should conform to local electrical safety codes.
■ Make sure the power supply voltage is correct before using the camera.
■ Do not drop the camera or subject it to physical shock.
■ Do not use the device beyond specified voltage range.
■ Do not place the camera in extremely hot, cold (the operating temperature shall be (-4˚F~122˚F), dusty or
damp locations, and do not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for operating environment.
If the product does not work properly, please contact the dealer or where the product was purchased.
Keep away from liquid while in use.
sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable,
ensuring the requirement of the HD monitoring in the traditional surveillance system.
This camera series is the latest technology and advanced circuit design, which features high definition and
Introduction
● High Resolution
Adopt high performance sensor, providing high definition and clear image.
● High Transmission Performance
Real-time transmission with high speed and long distance.
● High Light Compensation (HLC)
Mask and compensation the high light area.
● DNR
Reduce noise from brightness and color signal.
● OSD
Access the camera settings which can be clearly displayed through the main menu.
● White Balance
Adjust the color temperature according to the environment automatically.
● ICR Auto Switch
The filter will filter infrared light during the daytime and change to normal at night to
ensure a high sensitivity and clear image.
● AGC
Adjust the gain of amplifier, enabling the camera to output the standard video signal in different
lighting condition.
● Wide Dynamic Range (WDR)
When there are both very bright and very dark areas simultaneously in the field of view, this function
will balance the brightness level and provide clear images.
1

● Privacy Masking
This function allows you to block or mask certain area of a scene for privacy purpose.
● Backlight Compensation (BLC)
When the back of the captured object is too much bright, you can set BLC for the captured object to
make it clearer.
● Motion Detection
The alarm will be triggered when there are moving objects captured by the camera.
Cables
Power Cable
Video Output
Video Switch Cable
ON ON ON ON
1 1 1 1
2 2 2 2
AHD TVI CVI CVBS
Video Switch: Remove the cover of the video switch cable and set the video output as below.
2
Before you start, please make sure that the wall or ceiling is strong enough to withstand three times
the weight of the camera. Please install and use the camera in the dry environment.
You’d better install back the lens cover or lower dome less than 4 hours after removing it.
The mounting types of cameras are only for reference.
Installation
►Mounting for VLBT5W/VLBT6W
1. Drill the screw holes and the cable hole on the wall according to the drill template.
12.9mm 12.9mm
25.5mm
120°
120°
44.2mm ∅64.0
∅4.5
∅51.0
VLBT5W VLBT6W
∅4.6
∅25.1
∅82.0
∅72.2
120°
120°
62.5mm
18.1mm
36.1mm

2. Route and connect the cables .
3. Secure the mounting base with camera to the wall with screws as shown below.
4. Bracket adjustment. Before adjustment, preview the image of the camera on a monitor and then loosen the
fixed ring to adjust the view angle of the camera. Tighten the fixed ring after the adjustment.
5. Focus and zoom adjustment ( If the camera you get is fixed lens, please skip this step). Remove the
lens cover and then adjust the focus and zoom screws to get a clear image. Finally, tighten these two
screws and the lens cover.
3
Fixed Ring
Fixed Ring
Pan 360°
Pan 360°
Tilt 90°
Tilt 90°
Lens Cover
Focus
Zoom
►Mounting for Dome Camera
1. Loosen the screws to open the lower dome and then loosen the lock screw to remove the mounting base.
2. Attach the drill template to the place where you want to fix the camera and then drill 4 screw holes
and 1 cable hole (if you want to route the cables through the mounting base) according to the drill
template.
● Mounting for VLDT6W

3. And then secure the mounting base to the ceiling or wall with the screws
provided.
Route and connect the cables.
4. Fix the camera to the mounting base with the lock screw.
∅6
∅148
∅22
88 mm
89mm
Lock Screw
Lower Dome
Sponge
Mounting Base
4
5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then
adjust the camera according to the figure below to get an optimum angle.
Rotation 0°~360°
Pan 0°~360°
Tilt 0°~75°

7. Install the lower dome back to the camera with the screws and remove the protecti o n
film softly t o c o m p l e t e t h e i n s t a llation.
● Mounting for VLDT5W
1.
Drill the screw holes and the cable hole on the wall according to the drill template.
2. Loosen the screws to remove the lower dome from the camera.
5
74.25
74.25
(mm)
Lower Dome
3
4. Secure the mounting base with camera to the wall with screws as shown below.
. Route and connect the cables.
Rubber Plug

6
5.
adjust the camera according to the figure below to get an optimum angle.
6. Install the lower dome back to the camera and secure it with the screws.
Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then
Rotation 0°~355°
Pan 0°~355°
Tilt 0°~67°
● Mounting for VLT7W
1. Drill the screw holes and the cable hole on the wall according to the drill template.
2. Route and connect the cables. Then secure the camera to the ceiling or wall with the screws provided.
∅108
∅97.5
∅4.5
84.4mm
48.7mm
24.4mm
120° 120°
Rubber Plug
3.
image of the camera on a monitor. Tighten the lock screws after you finish adjusting the view angle of the camera.
Adjust the camera to obtain an optimum angle by loosening the lock screws. Before adjustment, preview the
Lock Screw

7
Specifications
Camera
Image Sensor
Resolution
Image size
Video Output
Image System
Electronic Shutter
IR Distance (feet)
Frame Rate
Min. Illumination
Lens Mount
S/N Ratio
Ingress Protection
Functions
Function Control
Day &Night
WDR
Digital NR
Global Exposure
Central Exposure
AGC
Auto White Balance
BLC
Front Light Compensation
Sharpness
Smart IR
Defogging
HLC
Image Setting
Defect Correction
Others
Power Supply
Power Consumption
Working Environment
Dimensions (inch)
1/2.8" COMS
2MP
1920×1080
AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI)
PAL/NTSC
Auto; 1/50s~1/100000s(PAL);1/60s~1/100000s (NTSC)
32.8~65.6 ~98.4
30fps(60Hz),25fps(50Hz)
Color:0.001lux@F1.2, AGC ON; B/W: 0lux with IR
M12 D14
≥
65.6 65.6~98.4 32.8~65.6 32.8~65.6
D14 M12 M12
×
52dB(AGC OFF)
IP66 IP66 IP66&IK10 IP66&IK10 IP66
OSD (UTC control)
ICR
Yes (120dB)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Auto
DC12V (± 10%)
IR OFF: < 1W; IR ON : < 4W
-4 °F ~ 122 °F, 10 % ~ 90 %(relative humidity)
Ф 2.76 6.14
Specifications
Models VLBT5W VLBT6W VLDT6M VLD T5W VLT7W
Ф3.43 4.25×
Ф4.61 3.54×
Ф5.90 4.49×Ф3.43 8.62×
2.8mm 2.8mm
2.8mm 2.8~12mm
Lens 2.8~12mm
(motorized)