Spectra H100TF User manual

war ning sig nals
ATTENTION: Installation must be carried out by an electrician in compliance
with the latest codes and regulations.
ATTENTION: Disconnect from power source before
installation or service to prevent electric shock.
ATTENTION: Lens on unit will be hot
allow to cool prior to removal.
Sounder 10mA
BR101305B 115V 5W
BR102305B 230V 5W
H100TF230G/x , 50/60Hz 230V AC
Unit current consumption
3
4
1
3
2
TONE 2 1200/500Hz
SWEEPING
2
1
2
1
G = Green Y = Yellow
H100 TF
B = Blue C = Clear
R = Red A = Amber
x = Lens colour
•
- +
through grommet
Cable entry: 1 x 5-7mm push
1.5mm² terminals
85 x 241.2mmDimensions :
1
2
3
3
2
1
@ 1Hz
•
TONE 3 800/1000Hz
TONE 1 BUZZER
@ 7Hz
SOUNDER
Beacon
PCB
Beacon 25mA
Trumpet Horn Flashing Filament
5W @ 1Hz BA9s Filament Bulb.
IP Rating: IP65
Temp: -25 C to +50 C
Unit weight: 219g
CE, UKCA
Order code Voltage
H100TF024G/x 24V DC
Unit current consumption
Sounder 10mA•
Beacon 250mA•
H100TF048G/x, 50/60Hz 48V AC
Unit current consumption
Sounder 35mA•
Beacon 110mA•
H100TF115G/x, 50/60Hz 115V AC•
Unit current consumption•
Sounder 19mA•
Beacon 35mA•
Bulb Type BA9s
E2S Part No. Version
BR10245B 24V 5W
BR10485B 48V 5W
Tel : [phone]
www.e2s.com
MIN
SHOWN SET TO MAX
MAX
N/- L/+
N~ L~
N/- L/+ E
TERMINAL
BLOCK
VOLUME CONTROL
3
D152-00-301-IS Issue 1 Sheet 1 of 2
19/01/2022
TONE FREQUENCY DESCRIPTION
1 BUZZER
2 1200/500Hz SWEEPING @ 1Hz
3 800/1000Hz @ 7Hz

L/+ N/- E
war ning sig nals
L/+ N/- E
20
5
TERMINAL
BLOCK
A/C
INPUT
D/C
INPUT
N/- N~ -
N/- N~(FROM BEACON) -(FROM BEACON)
L/+ L~ +
L/+ L~(FROM BEACON) +(FROM BEACON)
E
5
6
7
8
1
4
9
2
5
3
CONNECT
CABLE AS
SHOWN
8
CONNECT THE
BEACON CABLES
TO TERMINAL AS
SHOWN.
Dimensions in mm
10
6
7
L~N~
- +
L~
- +
N~
f
c
b
e
d
a
D152-00-301-IS Issue 1 Sheet 2 of 2
19/01/2022
Tel : [phone]
www.e2s.com
Sheet 2 of 2
19/01/2022
D152-00-301-IS Issue 1
INSERT CABLE
THROUGH GROMMET,
STRIP CABLE TO LENGTH.
100.0
CUSTOMER SUPPLIED
SCREWS 2 OFF TO
SUIT 4.5mm HOLE,
No. 8/M4.
45
45
2 POS'NS
INTO CABLE LOCKS IN
MAKE SURE THE
CABLE IS TUCKED FIRMLY
TERMINAL
BLOCK CUSTOMER
POWER CABLE
N
L
BEACON
CABLE
1
2
PLACE THE HEADER
PIN TO REQUIRED TONE
SEE SHEET 1,FOR DETAIL.
3
REPLACE
BULB, SEE
SHEET 1
FORPART
No.