Spectrum Industries 55107 User manual

Assembly Instructions
0191523 Page 1 of 4
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts
or accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Robot Device Charging Module
55107
(2) 0145039
Bar support
B-side
(with slots)
(4) 056284
8-32 Wing nut
(2) 0142528
Bar support
(with threaded
weld studs)
The Robot Charging Module can store and charge
up to 12 Sphero®robots, and 12 Sphero Minis®.
The tray can be swapped for other robot types*.
(1) 0144113
Robot charging module
*Contact Spectrum for a list of available trays or custom options.
Install chargers
1
1. Remove the (2) 1/4-20 x 5/8” PHM screws and remove the tray
assembly. Figure 1.
2. Place chargers inside module and plug into power strip or USB
hub (not included).
3. Replace tray assembly and secure with previously removed screws.
Figure 2
Tools
Required
Figure 1
1/4-20 x 5/8”
PHM screw
Chargers
Charge cords
Charge
cords
1. Remove (2) #8 x 3/8” PHSM screws and remove robot tray.
2. Route charge cords through the openings in the module. Be sure to
leave enough slack in the cords to reach all robots in the tray. Figure 2.
3. Replace tray and screws.
1/4-20 x 5/8”
PHM screw
Lower tray
Route cords
2
#8 x 3/8”
PHSM
Robot tray
#8 x 3/8”
PHSM
Tray
assembly

2
0191523 Page 2 of 4
CAUTION
While the rubber feet on the bottom of the module prevent scratching
of surfaces the module is placed on, screw heads protruding under the
unit can still possibly scratch these surfaces in some circumstances.
Place the module on a level surface using all 4 rubber feet. Do not
drag or slide the module across tables or worksurfaces. Use caution
when moving. Always remove all devices to reduce weight, and unplug
power strip prior to moving.
1. Plug charge cords into robot bases. Figure 3.
2. Place robots* into tray cutouts.
Robot
X 12
Install robots
3
Figure 3
Base
X 12
Mini
X 12
Charge cords
Figure 4
1. Plug charge cords into mini robots. Figure 4.
Connect charge cords
4
*Robots not included

Front bar Assembly
Rear bar Assembly
0191523 Page 3 of 4
Assemble bars
Figure 5
Bar support B-side
(with slots)
Bar support
(with threaded
weld studs)
Tab
Tab
8-32 Wing nut
(2 per assembly)
5
Installing module into cart or TechCenter - optional
1. The bars should be assembled with the tabs facing away from each
other as shown in Figure 5.
2. Loosen the (2) wingnuts slightly.
3. Repeat for the 2nd set of bars.
Note: When determining the location of the module,
be sure the module will clear any obstructions that
may be inside the cabinet and enough clearance
(height) is provided for all module devices.
Figure 6
Left slotted
uprights
Right slotted
uprights
Installing bars
6
1. Determine the approximate location (height) you would like the
module to be mounted. The rear bar is (2) slots higher than the front.
2. Insert one tab into a slot in the left slotted upright. Figure 6.
3. Insert the opposite tab into the corresponding right slotted upright
and fully extend the bar assembly into place.
4. Lock the extended position of the bars by securely tightening the (2)
wingnuts. Be sure both wingnuts are tight.
5. Repeat for the 2nd set of bars.
X 2

0191523 Page 4 of 4
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2019 Spectrum Industries Inc., All rights reserved.
1. Carefully set the empty module onto both sets of bars. Be sure the
rear channel “hooks” the rear set of bars fully. Figure 7.
Rear
channel
Figure 7
Robot Module
Installing module
7
Bars
Bars