Sper scientific 840080 User manual

MANOMETERS
840080, 840081, 840082,
840083, and 840085
INSTRUCTION MANUAL
SPER
SCIENTIFIC LTD.

2
CONTENTS
Title Page
1. Introduction.......................................................................... 2
2. Panel Description ................................................................ 3
3. Instructions
3-A. General Instructions ................................................. 3-4
3-B. Zero Setting.............................................................. 4
3-C. Calibration ................................................................ 4-5
3-D. Auto Power Off ......................................................... 5
3-E. Battery Replacement................................................ 5
3-F. RS232 Output........................................................... 5
3-G. Optional Accessories................................................ 5
3-H. Screen Examples ..................................................... 6
3-I. Troubleshooting........................................................ 6
4. Specifications
4-A. Model Range and Resolution .................................. 7
4-B. General Specifications ............................................ 7
4-C. Calibration Reference Point ..................................... 7
5. Warranty............................................................................. 8
1. INTRODUCTION
Ideal for measuring low differential pressure in clean rooms, test and
balance, medical equipment, HVAC, pneumatic systems and computer
peripherals. Model 840085 reads gauge pressure and differential pressure
(Imperial and Metric) in 5 units of measure: bar, psi, inH2O, mmH2O, and
mbar. All other models have 11 units of measure: bar, mmHg, ozin2, kgcm2,
psi, inH2O, kPa, ftH2O, inHg, cmH2O, and mbar. Features include a large
backlight display, max-min, hold, and auto power off functions. The RS232
port enables communication with a computer. High accuracy of ±0.3% fs at
25ºC, repeatability: ±0.2% (max ±0.5%) FSO, and combined linearity and
hysteresis: ±0.2 (Max ±1.0%) FSO.
CAUTION: During the Zero Setting (page 4). Make sure the tube is
disconnected and do not apply pressure to the connector. Doing so can
cause permanent damage to the unit, which is not covered by the warranty.

3
2. PANEL DESCRIPTION (Fig. A)
1. "-" Negative pressure hose plug.
2. HOLD Freezes pressure reading.
3. "-" Minus pressure display.
4. REC starts/displays max/min pressure.
5. MAX MIN pressure recorded.
6. BAT Low Battery Indicator
7. On/Off button
8. Hold button freezes pressure reading.
9. Unit button cycles through pressure readings.
10. "+" Positive pressure hose plug.
11. DIF Differential pressure mode.
12. Primary Data Screen.
13. H/M/S 88:88:88 Hr/Min/Sec.
14. Pressure unit indicator.
15. RS232 output port.
16. DC power input for AC adapter.
17. Rec button starts the relative clock.
18. Dif button displays relative zero.
19. Backlight button lights LCD for apx. 30 seconds.
20. Battery Compartment.
NOTE: Some functions shown on the display are not available.
3. INSTRUCTIONS
3-A. General Instructions
The Manometer measures “Gauge Pressure.” This combines Differential
pressure with a PSI measurement as referenced to ambient pressure. When
the manometer is first powered on, the entire LCD display flashes for
approximately 3 seconds. The LCD is divided into two distinct sections: One
large (Primary) top screen and one smaller section at the bottom-right of the
LCD (Relative Clock). The pressure measurements are constantly updated in
the 2 display areas. Check that the tubing is not leaking or damaged before
use. The start-up mode is programmable. The display will default to the mode
last used and the meter defaults to the setting used during the last operation.
•Turn the unit on with the ON/OFF button.
•Press the REC button once, and the relative clock starts in the lower right
screen. "REC" is displayed in the middle-left of the LCD (Pg 6, Fig B). The
DIF button will not operate at this time.
•Press the REC button repeatedly to cycle through MAX (Pg 6, Fig C) and
MIN (Pg 6, Fig D) and back to the current pressure. To exit the record
mode, press and hold the REC button for 3 seconds.
1
2
3
4
5/6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
-8.8.8.8
HOLD DIF
REC H/M/S
MAX MIN BAT 88:88:88
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

4
•Press HOLD to freeze the pressure reading (Pg 6, Fig E). Press the
HOLD button again to release this setting.
•Press the DIF button and "DIF" appears near the top of the LCD and the
display indicates the relative zero. Only the amount of the pressure
change will be indicated (Pg 6, Fig F). Press the DIF button again and
the unit returns to the normal mode.
•Press the UNIT button repeatedly to cycle through the units of measure
indicated below the LCD display (Pg 6, Fig G and H)
•Press the Backlight button and the LCD illuminates for approx. 30
seconds then turns off automatically.
Note: Differential Pressure is a measure of the difference between two
pressures, for example, use differential pressure sensor to measure gauge
pressure by leaving one process connection open to atmosphere and
connecting the second sensor port to your system.
3-B. Zero Setting
Do not apply pressure to the connector and disconnect the tube. Failure to
follow this procedure can cause damage and void the warranty. To set the
display to zero, turn the unit on and press the HOLD button for 2 seconds.
The LCD displays "o o o o" one at a time, from left to right. Next, the LCD
clears and displays a zero setting (Pg 6, Fig I).
3-C. Calibration
The meter is factory calibrated. Annual recalibration at a qualified meter
calibration facility is recommended. The following information is for the
calibration technician:
Use a standard manometer calibrator to calibrate this unit. Refer to the
Calibration Point Reference chart on page 7. The examples are for model
number 840083, with a pressure range from 0 to +100 PSI (positive pressure)
or from 0 to -100 PSI (Negative pressure). The meter must be attached to a
pressure source between 75.0 and 85.0.
•Set the display to zero (refer to Zero Setting above).
•Turn the meter off.
•To begin positive (+) calibration, press the Rec and On buttons
simultaneously. "CA" (calibration) shows on the LCD. (Pg 6, Fig J).
•As the meter enters the calibration mode, press the Unit button as
needed to select "psi" (Press the UNIT button again to skip positive and
advance to the negative (-) calibration point.)
•The meter defaults to 80 psi calibration point, the adjustable pressure
range is from 78.0 to 82.0. If the calibration pressure source is not 80 psi,
increase the digits by pressing the DIF button, or decrease the digits by
pressing the BACKLIGHT button. Save the calibration point by pressing

5
the REC button. "SA" (save) and "CA" will appear on the screen.
•Follow the same procedure for the negative pressure calibration point. By
pressing the UNIT button, the LCD now displays "-80.0" and a small "CA".
Save the calibration point by pressing the REC button. "SA" and "CA" will
appear on the screen, followed by "End" and "CA". In 2 seconds, the
meter returns to normal mode.
•Press the Unit button to exit the calibration mode.
Note: If you can not save by pressing the REC button, check that the
calibration pressure source is between 75.0 and 85.0; and that you entered the
correct positive pressure (+) or negative pressure (-).
3-D. Auto Power Off
This unit has a built-in Auto Power Off function to prolong battery life. The
meter will power off automatically if no buttons are pressed within 20 minutes.
To deactivate this feature, press On and Hold simultaneously before power-
ing on the unit. The symbol "n" will appear in the middle of the screen, at which
time you can release the Hold button.
3-E. Battery Replacement
When the "BAT" icon appears on the right side of the LCD, open the battery
cover, install a fresh 9V battery and replace the cover. Remove the battery
during prolonged periods of non-use.
3-F. RS232 Output
The unit features an RS232 output via which can be utilized by user's specific
application. Connection procedures:
•Connect the optional RS232 cable to the RS232 output port.
•Plug the other end of the RS232 cable into computer's COM 1 or 2 port.
•Install the optional RS232 Software according to the procedures in the
software package. Additional instructions are found in a separate Adobe
PDF file in the software. Be sure to set the baud rate to 2400.
3-G. Optional Accessories
•840027 AC Adaptor
•840054 RS232 Cable
•840052 Software
•840089 Rubber Holster
•840090 Water Resistant Instrument Pouch
•840094 USB Adaptor Cable

6
Fig. B Fig. C Fig. D
3-H. Screen Examples
Fig. H Fig. I Fig. J
15.3
REC H/M/S
MAX ▼00:10:35
DIF
0.0
▼
80.0
▼CA
_ 0.0
▼
0.985
▼
14.3
▼
8.3
▼
HOLD
14.3
REC H/M/S
▼00:10:35
11.3
REC H/M/S
Min ▼00:10:35
Fig. E Fig. F Fig. G
3-I. Troubleshooting
If the power is on, but there is no display, replace the battery or attach the
optional AC adaptor. Check that the tubing is tightly connected.
Error Code Action
BAT Replace the battery.
Err.1 The pressure value exceeds the maximum range.
Err.2 Measurement pressure is less than minimum range.
Err.3 While in the DIF function, the differential pressure value is larger
than maximum display digit.
Err.4 During Zero Setting, make sure the tubing is disconnected with
no pressure applied to the connector. If you still receive this
error message after disconnecting the tubing, the sensor or
meter may be damaged.
E10L or
E2UL
While using the RS232 software, the pressure source is less
than, or over the range of the instrument.
NOTE: Exceeding maximum pressure will cause permanent sensor damage.
Before you connect the instruments to a pressure source, carefully check your
fittings and hoses.

7
4-C. Calibration Point Reference
Model PSI Range Calibration Recommended
840085 0 ~ ±2 1.6 1.5 ~ 1.7
840080 0 ~ ±5 4.000 3.900 ~ 4.100
840081 0 ~ ±15 12.00 11.70 ~ 12.30
840082 0 ~ ±30 24.00 23.40 ~ 24.60
840083 0 ~ ±100 80.00 78.00 ~ 82.00
4-B. General Specifications
Dimension 7 1/8” x 2 3/4” x 1” (182 x 72 x 30 mm)
Weight 5 oz (150 g)
PSI Range 0 ~ 2, 15, 30, or 100
Accuracy ±0.3% of full scale at ±25°C
Response time 0.5 seconds
Format Baud Rate : 2400 bit/sec, Data Bit : 8,
Stop Bit : 1 P XXXXX , P - XXXXX (unit)
Storage temperature range -4~140°F (-20 ~ 60°C)
Operating Humidity Max. 80% RH
Operating temperature 32 ~ 122°F (0 ~ 50°C)
Power One 9.0 volt battery or AC Adaptor
4. SPECIFICATIONS
Model 840085 840080 840081 840082 840083
Range Res Range Res Range Res Range Res Range Res
PSI: 2 0.004 5 0.003 15 0.01 30 0.02 100 0.1
inH²0: 55.4 0.01 138 0.1 415 0.3 830 0.5 2768 2
bar: 0.138 0.001 0.345 0.001 1.03 0.001 2.07 0.002 6.89 0.004
mbar: 138 0.1 345 0.2 1034 1 2068 2 6895 4
cmH²0:
(840085 is
in mmH20)
1410 0.01 352 0.2 1050 1 2110 2 7030 4
mmHg:
Not Applicable
259 0.2 776 0.5 1550 1 5170 3
ozin²: 80 0.05 240 0.2 480 0.3 1600 1
kgcm²: 0.35 0.001 1.05 0.001 2.1 0.002 7.03 0.004
kPa: 34.5 0.02 183 0.1 207 0.2 684 0.4
ftH²O: 11.5 0.01 34.6 0.02 69.2 0.04 231 0.2
inHg: 10.2 0.007 30.54 0.02 61.08 0.04 203.6 0.12
max pres: 20 PSI 20 PSI 30 PSI 60 PSI 150 PSI
4-A. Model Range and Resolution

8
Rev. 02/16/07
5. WARRANTY
1 YEAR METER WARRANTY
Sper Scientific warrants this product against defects in materials and workman-
ship for a period of one (1) year from the date of purchase, and agrees to
repair or replace any defective unit without charge. If your model has since
been discontinued, an equivalent Sper Scientific product will be substituted if
available. This warranty does not cover probes, batteries, or damage resulting
from accident, misuse, or abuse of the product. In order to obtain warranty
service, simply ship the unit postage prepaid to:
SPER SCIENTIFIC LTD.
7720 East Redfield, Suite 7
Scottsdale, Arizona 85260
[phone]
Email: [email protected]
Website: www.sperscientific.com
Be sure to include your name, address, phone number, and a detailed
explanation of why you are returning the item.