SPIETH Gymnastics 1383124 Use and care manual

Assembly and user manual
‘Club’ Uneven bars stand alone
1383124
Contact:
www.spieth-gymnastics.com
[email protected]

Assembly and user manual
2
S AFETY REGULATIONS
WARNING
In order to reduce the risk of in ury and to assure secure functioning of the
(gymnastic)apparatus, rules mentioned below are to be strictly followed:
1. Use this apparatus only under the supervision of a trained and qualified
instructor.
2. Check this apparatus for proper stability before each training, use it only in
perfect technical condition.
3. Always check the apparatus for its correct installation, particularly for the
fixation mechanism, before each use.
If there are any doubts, do not use the apparatus and get a professional
check.
4. Please consider your own limits and the restrictions of this gymnastic
apparatus.
5. Obstructive items or persons in close proximity of the apparatus are not
allowed.
6. Provide appropriate safety zones in the surroundings of the apparatus.
7. Never use the apparatus under the influence of alcohol, medication or drugs.
8. Pregnant women or persons with health issues should not use the apparatus.
Do not attempt to repair any damage to the apparatus yourself but contact your
supplier for advice or technical assistance.
Any unauthorised repair, alternation, removal of parts or change of specifications of
the apparatus is strictly prohibited for reasons of safety and will automatically and
immediately and without any prior notice end any warranty or right of compensation
in any form whatsoever.
General advice:
The life period of (gymnastic) apparatuses and mats is limited. Also materials wear
off after a certain period of time. Please check all parts , which are sub ect to severe
wear and tear, at least once every 3 months. This is mainly relevant for the security
of ad ustable parts and mechanisms, e.g. rails, bars, rings. Replace any worn off,
defective and missing parts. If there are any doubts, ask for advice from one of our
specialists.
For security reasons, we suggest to perform a maintenance check of all apparatuses
and mats by a specialist, once a year. This check can be part of a yearly or six month
safety check.
We would like to point out to you the possibility of a maintenance contract with our
firm.
This apparatus must be used in dry conditions only. Humidity will have a negative
effect on all types of upholstery used on (gymnastic) apparatuses and results in a
shortened lifespan.

Assembly and user manual
3
U SERS
The mounting and storing of this device may only be executed by competent adult
persons, who have read and understood the safety regulations of this manual.
C ORPORATE S OCIAL R ESPONSIBILITY
During the development and design of our apparatus and sporting equipment
we are concerned about your safety but we also consider the environment and society.
We do this for example by using sustainable materials like FSC or PEFC certified wood,
Phthalate free mats and Nexan sport balls with the No Child Labour Guarantee.
We are also constantly trying to lower our waste and energy consumption.
We believe that all children should have the ability to play sports and exercise.
That’s the reason why we have a close collaboration with the Sports for Children
Foundation.
Sports for Children collects used sporting equipment in the Netherlands, refurbishes
and donates them to schools and sporting clubs in Eastern Europe.
Thanks to this cause we can offer children the possibility to play sports in places
where otherwise they would not have sporting and exercising facilities.
Curious about how this works? Contact us for more information.

Assembly and user manual
4
Lay the base frame on a flat surface and carefully place the uprights in the
therefore designed cavities.
Make sure the mounting points for the width ad ustment point outwards.
When the upright is in position, place bushes in the base frame, on both sides
of the upright.
Fasten the upright to the base frame with the M10x25 Flat head countersunk bolts
using an Allen key.

Assembly and user manual
5
In order to mount the diagonal distance interlock to the high upright,
use a M10x20 button head bolt (incl. Loctite sealing) with a washer M10
and for mounting it to the lower upright,
use a M10x25 button head bolt (incl. Loctite sealing) with a washer M10.

Assembly and user manual
6
Mount the width ad uster to the uprights using
button head bolts M10x20 with washers M10
and fasten them tightly.
Make sure the lever is always positioned on the lower upright.
Position the rail above the slot in the clamping
head. Mount the rail to the clamping head, using the locking pin. Press and hold the red
button while mounting.
ATTENTION:
When reinserting the locking pin,
make sure the pin is fully
inserted as shown on the right pic.

Assembly and user manual
7
In order to ad ust the height of the rails,
turn the grip counter clockwise to unlock
and pull him out.
For extra support when ad usting the height,
there is a knob on the outside.
The uprights are equipped with a supportive
spring, inside the upright.
When the desired height is reached, push back
the grip until it clicks and turn the grip
clockwise to lock the height ad ustment.
Before use, always check that all red warning
indicator buttons, do not protrude.
In order to transport the uneven bars the feet need
to be folded.
Then move all four levers clockwise to open the
transport system.
When the uneven bars are positioned, move all four levers counter clockwise to
hide the transport system. Now the feet can be folded out.

Assembly and user manual
8
For official FIG height use the number indicated with dashes on either upright.
F.I.G –Settings
Upright short -6- 1700mm
Width ad uster -16- 1800mm
Upright high -7- 2500mm
2500
18
00
1700

Assembly and user manual
9
Maintenance instructions
-Check if the stainless steel rail holders are provided with a nylon disc.
-Grease the rail holders (by using Vaseline).
-It is absolu ely forbidden to use sandpaper when cleaning the rails. Remove magnesia
only when the rails are dry, to prevent that the soft parts of the veneer will be
removed as well.
Only use scouring pads. Velcro (hook) is a good al erna ive.
-Check if width ad usters work well.
-Check if the bolts that link the width ad usters to the uprights are well-tightened.
-Check if the bolts of the inner tubes are well-tightened.
Clean the metal parts of the frame with a non-corrosive cleaning product.

Find your local reseller at
:
www.spieth-gymnastics.com