Spirit Commercial CIC800 User manual

CIC800 FITNESS BIKE
OWNER’S MANUAL
16207878000

Spirit Fitness

3
TABLE OF CONTENTS
5
6
6
6
8
21
22
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT OPERATION INSTRUCTIONS
PRODUCT REGISTRATION
MANUFACTURER’S LIMITED WARRANTY
CIC800 ASSEMBLYINSTRUCTIONS
EXPLODED VIEW DIAGRAM
PARTS LIST
Thank you for purchasing our product, please save these instructions. Please do not perform or attempt any
customizing, adjustments, repair or maintenance that is not described in this manual.
www.spiritfitness.ca

4
Spirit Fitness
Thank you for your purchase of this quality stationary bike trainer from Dyaco Canada Inc.
Your new bike was manufactured by one of the leading fitness manufacturers in the world and
is backed by one of the most comprehensive warranties available. Through your dealer, Dyaco
Canada Inc. will do all we can to make your ownership experience as pleasant as possible for
many years to come. The local dealership where you purchased this bike is your administrator
for all Dyaco Canada Inc. warranty and service needs. Their responsibility is to provide you
with the technical knowledge and service personnel to make your experience more informed
and any difficulties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone number,
and the date of purchase below to make any future, needed contact easy. We appreciate your
support and we will always remember that you are the reason that we are in business. Please
complete and mail your registration card today and enjoy your new bike.
Yours in Health,
Spirit Fitness NAME OF DEALER _____________________________________
DEALER PHONE # _____________________________________
PURCHASE DATE _____________________________________

5
IMPORTANT SAFETY
INSTRUCTIONS
WARNING
•Use this equipment only for its intended use as described
in this manual. Do not attempt to ride this bike at high
pedal speeds until you have ridden the bike for some
time and are comfortable riding at slower pedal speeds.
•The bike is NOT equipped with a freewheel system
which means that when the flywheel is in motion, the
pedals will be in motion. Do not attempt to stop the unit
by applying backward pressure to pedals while they are
turning as knee injury may occur. Do not attempt to
remove your feet from pedals while they are moving.
•Wait for flywheel to coast to a stop before dismounting
the bike. If you want to stop the flywheel, push down on
the resistance/brake knob.
•Serious injury or death may occur from over-training.
Consult a medical doctor or qualified fitness instructor to
determine an exercise program appropriate for your
level of fitness.
•Do not attempt to turn the pedal cranks by hand. Do not
touch any driving mechanism while it is in motion as
possible injury could occur.
•Do not attempt to perform dip movements on
handlebars.
•Never drop or insert any object into any opening of the bike.
•In a home setting, keep children away from the bike
when it is not in use. Keep children and pets away
from the unit while it is in use.
•Only use the bike on a stable, level floor.
•Follow instructions for safe use of the equipment
including proper seat position, handlebar position, and
use of foot positioning system of pedals. Do not
attempt to pull up handlebar post and seat post over
the ‘MAX.’ level
•For safe operation, allow for at least 1foot (30cm) of
free space to either side of the unit and 2 feet (60cm)
of free space to the rear of the unit.
•Regularly examine the bike for damage and
wear. Inoperable components should be replaced
immediately or the equipment should not be used until
it is repaired.
•This appliance is not intended for use by persons with
reduced physical, sensory or metal capabilities, or lack
of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
•Keep children under the age of 13 away from
this machine.
•Failure to follow all guidelines may compromise the
effectiveness of the exercise experience, expose
yourself (and possibly others) to injury, and reduce the
longevity of the equipment.
www.spiritfitness.ca

6
www.spiritfitness.ca
PRODUCT
REGISTRATION
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product in the
space provided below.
Serial Number:
_______________________________________
REGISTER YOUR PURCHASE
The self-addressed product registration card must be
completed in full and returned to Dyaco Canada Inc. You
can also register your purchase from our website.
http://dyaco.ca/index.html
SAVE THESE INSTRUCTIONS - THINK SAFETY!
IMPORTANT OPERATION INSTRUCTIONS
NEVER expose the bike to rain or moisture. This product is
NOT designed for use outdoors, near a pool or spa, or in
any other high humidity environment. Maximum environmental
ratings are 40-120 degrees Fahrenheit, 95% humidity non-
condensing (no water droplets forming on surfaces).
MANUFACTURER'S
LIMITED WARRANTY
Dyaco Canada Inc. warrants all it’s bike parts for a
period of time listed below, from the date of retail sale, as
determined by a sales receipt. Dyaco Canada Inc.’s
responsibilities include providing new or remanufactured
parts, at Dyaco Canada Inc.’s option, and technical
support to our independent dealers and servicing
organizations. In the absence of a dealer or service
organization, these warranties will be administered by
Dyaco Canada Inc. directly to a consumer. The warranty
period applies to the following components below:
COMMERCIAL WARRANTY (DUES PAYING FACILITY)
Labour 1 Year
Parts 3 Years
Wear items 1 Year
(grips, end caps and toe cage straps)
10 Years
LIGHT COMMERCIAL WARRANTY (NON DUES PAYING FACILITY)
Labour 1 Year
Parts 3 Years
Wear items 1 Year
(grips, end caps and toe cage straps)
Frame 15 Years
Frame
Labour 1 Year
Parts 3 Years
Wear items 1 Year
(grips, end caps and toe cage straps)
Frame Lifetime
HOME WARRANTY

7
SEAT
SEAT FORWARD/AFT ADJ.
SEAT HEIGHT ADJ.
MAIN FRAME
LEVELERS
REAR STABILIZER
TRANSPORT WHEELS
FLYWHEEL
PEDALS
FRONT STABILIZER
RESISTANCE ADJUSTMENT
HANDLEBAR ADJUSTMENT
HANDLEBAR FORWARD/AFT ADJ.
www.spiritfitness.ca

8
Spirit Fitness
CIC800 PRE-ASSEMBLY
UNPACKING
1. Cut the straps, then along the dotted line on the bottom of the box;
lift the box over the unit and unpack.
2. Locate the hardware package. The hardware is separated into six
steps. Remove the tools rst. Remove the hardware for each step as
needed to avoid confusion. The numbers in the instructions that are in
parenthesis (#) are the item number from the assembly drawing
for reference.
TOOLS INCLUDED:
M22 Wrench
Combination 6mm Allen Screwdriver
4mm Allen Wrench
5mm Allen Wrench
13/17mm Combination Wrench
PARTS INCLUDED:
1 Main Frame
1 Front Stabilizer
1 Rear Stabilizer
1 Adjustment Handle
1Water Bottle Holder’
1 Handlebar Post
1 Handlebar
2 Foot Pedals
1 Hardware Kit

9
CIC800 STEP ONE
2
44
42
45
42
HARDWARE FOR STEP 1
PART TYPE DESCRIPTION QTY
44 SCREW M5X1.25X55L 2
42 FLAT WASHER M8 4
45 NYLON NUT M8X1.25 2
1. Gather HARDWARE FOR STEP 1.
2. Position the FRONT STABILIZER (2) on
the FRAME BRACKET as showed in the
figure. Make sure the TRANSPORT
WHEELS are facing up and toward the
front of the bike.
3. Attach the STABILIZER with 2 HEX
SCREWS (44), 4 FLAT WASHERS (42)
and 2 NYLON NUTS (45). Do not over
tightened as the deformation of
stabilizer may occur.
4. Make sure the LEVELING FEET with nut
are fully screwed into the STABILIZER

10
Spirit Fitness
CIC800 STEP TWO
3-2
3-3
3-2
3-3
3
44
42
42
45
HARDWARE FOR STEP 2
PART TYPE DESCRIPTION QTY
3-2 HEX NUT M8 2
44 SCREW M8X1.25X55L 2
42 FLAT WASHER M8 4
45 NYLON NUT M8X1.25 2
1. Gather HARDWARE FOR STEP 2.
2. Assemble the FOOT LEVELER (3-3) and
HEX NUT (3-2) onto the REAR
STABILIZER (3)
3. Position the REAR STABILIZER (3) on the
FRAME BRACKET as showed in the
figure.
4. Attach the STABILIZER with 2 HEX
SCREWS (44), 4 FLAT WASHERS (42)
and 2 NYLON NUTS (45). Do not over
tightened as the deformation of
stabilizer may occur.
5. Make sure the LEVELING FEET with nut
are fully screwed into the STABILIZER

11
CIC800 STEP THREE
51
NO HARDWARE FOR STEP 3
1. Remove the T-POP (51) from the
components box and turn clockwise
to tighten rmly into the FRAME with
WRENCH (A).

12
Spirit Fitness
HARDWARE FOR STEP 4
PART TYPE DESCRIPTION QTY
32-2 SCREW M8X1.25X12L 2
1.
2.
Gather HARDWARE FOR STEP 4.
Assemble the HANDLEBAR POST ADJUSTMENT
(32-7) and ADJUSTABLE HANDLEBAR (32-1)
with 2 SOCKET HEX SCREWS (32-2)
3.
4.
Pull out the KNOB (32-11) and slide the
HANDLEBAR onto the POST (32-3).
Insert the HANDLEBAR ASSEMBLY into the
FRAME TUBE and tighten rmly with T-POP PIN
CIC800 STEP FOUR
32-2
32-1
32-7
32-3
32-11

13
CIC800 STEP FIVE
49
22
37
HARDWARE FOR STEP 5
PART TYPE DESCRIPTION QTY
49 SCREW M6X1.0”x15L 2
22 FLAT WASHER M6 2
1. Gather HARDWARE FOR STEP 5.
2. Assemble the BOTTLE HOLDER (37) with 2 SOCKET
HEX SCREWS (11) and 2 FLAT WASHER (13)

14
Spirit Fitness
CIC800 STEP SIX
52
52
NO HARDWARE FOR STEP 6
1. Remove pedals from the components box.
2. Look at the end of the pedal axle and notice each
pedal is marked with an R and L on the spindle. It is
indicated which side of bike the pedal is intended
to assemble.
3. Locate the pedal marked R on the spindle on the
right side of crank (Chain guard side). Turn clockwise
to tighten rmly. If possible, apply some grease to the
threads before engaging to the crank.
4. Locate the pedal marked L on the spindle on the Left
side of crank. Turn counter-clockwise to tighten rmly.
If possible, apply some grease to the threads before
engaging to the crank.

15
INDOOR CYCLE SETUP
LEVELERS
Place the cycle on a level area, if at all possible. If the cycle needs leveling, turn the levelers clockwise or
counterclockwise until the base is stable and does not rock.
ADJUSTMENT KNOBS
All four adjustment levers function the same way. Turn the knob clockwise to tighten and counterclockwise
to loosen.
SEAT
The pitch of the saddle can be adjusted to accommodate all users. Loosen the horizontal bolt under the seat to
adjust the pitch, then retighten.
TRANSPORTATION
The indoor cycle is equipped with two transport wheels, which are engaged when the rear of the CIC800
indoor cycle is lifted.

16
Spirit Fitness
Take some time to learn how to properly adjust the bike to your body; it will make your workouts more pleasant
and a safer experience too. Riding the bike when it is incorrectly adjusted can result in discomfort and increase
your risk of injury.
ADJUSTMENT OF SEAT POSITION
SEAT HEIGHT ADJUSTMENT
1. Standing next to the bike, adjust the seat until it is about hip height.
2. Rotate the crank arms until the pedals are in the vertical position: 12 and 6 o’clock.
3. Place your foot in the toe cage of the pedal closest to the oor and mount the bike. Ensure that
the ball of your foot is over the center of the pedal. Your leg should be slightly bent at the knee,
about 5 degrees.
4. If your leg is too straight or your foot cannot touch the pedal you will need to lower the seat
height. If your leg is bent too much, you will need to raise the seat height.
5. Dismount the bike. Then loosen the knob on the seat post and adjust up or down as necessary.
6. When the seat is in the desired position, tighten the knob to secure the seat post.
7. Note the nal position mark on the seat post for future reference.
SEAT FORWARD/AFT ADJUSTMENT
1. Sit on the bike with the crank arms in the 3 and 9 o’clock positions. A proper forward/aft
position (for road bike training) of the seat is achieved when the small bump at the top of your
shin is above the pedal axle.
2. Dismount the bike. Loosen the knob under the seat and slide the seat forward or backward as
desired; tighten the knob.

HANDLE BAR ADJUSTMENT
HANDLEBAR HEIGHT ADJUSTMENT
1. The handlebar height is a matter of preference. Start with a handlebar height that is the same
as the seat’s height. Adjusting the handlebar higher will give the rider a more upright posi-
tion; lower will result in a more crouched position.
2. Raise or lower the handlebar by loosening the knob on the handlebar post and adjust by
sliding the handlebar mount up or down as desired. Then tighten the knob to secure the han-
dlebar post. Note the nal position mark on the handlebar post for future reference.
ADJUSTMENT OF HANDLEBAR’S FORWARD/AFT POSITION
1. Loosen the knob under the handlebar and slide the handlebar forward or backward as desired. A suitable forward/aft
position should allow the rider to comfortably grasp the handlebar with a slight bend at the elbow.
2. Tighten the knob to secure the handlebar assembly.
17

18
Spirit Fitness
RESISTANCE ADJUSTMENT
Resistance can be adjusted easily at any time while riding to change the intensity of
workout. Turn the knob clockwise (+) to increase resistance. Turn the knob counterclockwise
(-) to decrease resistance.
EMERGENCY BRAKE
In case of emergency or before dismounting the indoor cycle, presses directly DOWN on
the resistance knob to stop the ywheel and pedal.
PEDAL STRAP ADJUSTMENT
Place the ball of you feet in the toe clip till the front of the shoe is snugly in the cage. Then
tighten the strap of toe clip around your shoe by pulling up on the strap until cage of toe
clip ts snugly around the shoe.

19
BELT TENSION ADJUSTMENT
The belt tension had been set before shipping. It should not need to be adjusted when rst using. However,
you may need to make the minor tension adjustment over time.
NOTE: Make sure you adjust both side equally, either tighten or loosen the belt tension so that the ywheel
keep in alignment with the frame.
TIGHTEN THE BELT TENSION
Move the crank arms back and forth. If there is more than 1/4” (0.64cm) movement in the crank before
ywheel starts turning, you will need to adjust the belt.
1. Loosen the two-anged nut(A) on either side of ywheel.
2. Moving the ywheel forward by evenly tightening clockwise the 2 hex bolts(B), which go through the frame tube
until there is approximately 1/4” (0.64cm) of slack in the belt.
3. Re-tighten the two-anged nut on either side of ywheel and then put back the safety cover.
GENERAL MAINTENANCE
1. Wipe down all areas in the sweat path with a damp cloth after each workout.
2. If a squeak, thump, clicking or rough feeling develops the main cause is most likely one of two reasons:
a. The hardware was not sufciently tightened during assembly. All bolts that were installed
during assembly need to be tightened as much as possible. It may be necessary to use a larger wrench than the one
provided if you cannot tighten the bolts sufciently. We cannot stress this point enough; 90% of calls to the service
department for noise issues can be traced to loose hardware.
b. The crank arm nut needs to be retightened.
c. If squeaks or other noises persist, check that the unit is properly leveled. There are 2 leveling pads on the bottom of the
rear stabilizer, use a 14mm wrench (or adjustable wrench) to adjust the levelers.

20
Spirit Fitness
MAINTENANCE SCHEDULE
1. Do not service internal parts of pedals. If they are found to be worn internally, we recommend replacing the pedal.
2. Use of lubricants or cleaning solutions other than those so specied will result in diminished performance and a
shorter life span for that part.
Part Recommended Action Frequency Cleaner
Pedals Ensure that pedals are tight in crank arms,
that all screws on pedals are tight, and that
the pedal straps are not frayed.
Before each Use N/A
Frame Wipe down using a clean, soft damp cloth Daily Water
Flywheel Wipe down using a clean, soft damp cloth Weekly Water
Brake Pad Check for wear Monthly N/A