Spirit Halloween Twitching Banshee Parts list manual

EASY ASSEMBLY AND OPERATION INSTRUCTIONS
01257732 Twitching Banshee
This item, when assembled by the following instructions,
should take 15 minutes to assemble. Please follow the step
by step guide and enjoy your Twitching Banshee!
STEP 1 STEP 2
PROCEED TO PAGE 2 > >1/3
PARTS LIST
A. Base
B. Support Poles x 4
C. Costume
D. Torso Frame
E. Hip Hoop
F. Upper Torso Frame
G. Head
H Left Arm
I. Right Arm
UL Adapter *
* UL Power Adapter Spec
Input: 100 - 240VAC 50/60Hz
Output: 5.9V 1A
CARE AND STORAGE INSTRUCTIONS
For best performance operate your item indoors or in a sheltered outdoor area.
We also recommend that you bring your item indoors during adverse weather
(extreme cold, strong winds and/or rain). When not in use, store this product
in it’s original packaging. Keep away from heat and moisture.
A
F G H I
NOTE: The longer end of the (A) Base goes towards the front. First, assemble the (B) Support
Poles to each other and to the (A) Base as shown, and secure by aligning the quick-connect
push buttons into the pre-drilled holes.
NOTE: The (C) Costume opens/closes at the back.
Next, lower the (C) Costume over the (B) Support Poles through the bottom & out through the
neck opening of the (C) Costume.
WARNING
This item is not a toy and should be used for decoration only. This item contains small parts that can be a
choking hazard. Keep all plastic and wire parts away from children. This product is intended for people
ages 14 and up.
1. Please use the applicable transformer or the one supplied by manufacturer。
2. Please install the product according to the instruction, the connecting wire should be connected in the
correct color
3. Children should be supervised by adults when using the product and keep the transformer away from
kids。
4. The transformer should be inspected regularly。
Please read all instructions carefully before assembling. Save this instruction sheet for future reference
B C D E
1
2
3
C
B B
B
B B
A
B
BB

STEP 3
STEP 4
STEP 5
PROCEED TO PAGE 3 > >2/3
STEP 6
Attach the (D) Torso Frame on top of the (B) Support Poles and secure by aligning the
quick-connect push buttons into the pre-drilled holes. Lower the (E) Hip Hoop down over the (D)
Torso Frame and attach through the slots located on the sides at the bottom of the (D) Torso
Frame as shown.
Attach the (F) Upper Torso Frame into the slot housings on the (D) Torso Frame as shown. Set the
(G) Head onto the “neck” slot housing on the (F) Upper Torso Frame and secure by aligning the
quick-connect push button into the pre-drilled hole.
Now, plug the UL Power Adapter into the input receiving jack
marked “DC 5.9V” on the Function Control Box and route the UL
Power Adapter down and out the bottom of the item.
OPTIONAL: If you choose to use the Step Here Try-Me
Activation Pad , plug the connector into the input receiving
jack marked “TRY ME” on the Function Control Box and set the
Step Here pad in front of the character when ready to display.
Connect the cables from the (H) Head,
the (D) Torso Frame, and the (C) Costume
to the color-coordinated cables on the
Function Control box on the (F) Upper
Torso Frame as shown.
Slide the (I) Right Arm up through the right sleeve and slide the forked-hook into the right
“shoulder” slot housing on the (F) Upper Torso Frame. Slide the (J) Left Arm up through the left
sleeve and slide the forked-hook into the left “shoulder” slot housing on the (F) Upper Torso
Frame as shown.
Sensor / Détecteur / Sensor
5.9 V
Try me / Essaie-moi / Pruébame
STEP
HERE
UL
ADAPTER
J
F
B B
G
G
E
E
E
E
G
D
D
C
C
I
I
H
H
E
E
D
D
(Not Included)

STEP 7
3/3
OPERATION INSTRUCTIONS
1. Plug the UL Power Adapter into a standard power outlet and adjust the settings on the Function Control Box
to your liking.
2. Twitching Banshee has 3 operation settings which can be found on the main Function Control
Box on the (F) Torso Frame:
• “ ” On: This setting allows the item to run continuously.
•Sensor: This setting allows the item to only be activated when the infra-red sensor is activated.
The item will operate for one audio-cycle with each sensor activation.
• The Infra-red (IR) sensor will activate when someone comes within an 80-degree angle from
left-to-right, as well as from above and below.
• The Infra-red (IR) sensor has a range of up to 2 meters/6.56 feet, and can work in all lighting
conditions – bright light to no-light!
• “ ” Off/Try-Me: This setting allows the item to be activated only if the Try-Me is triggered. The item
will operate for one audio-cycle with each Try-Me activation.
The Function Control box also includes a Volume Control knob, which allows you to adjust the volume
to be as loud or as quiet as needed. Be sure to test the item before finalizing your display so you can
set the volume to your liking.
ENJOY YOUR TWITCHING BANSHEE!
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures; Reorient or relocate the receiving
antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. Consult the dealer or experienced radio/TV technician for help.
Sensor / Détecteur / Sensor
5.9 V
Try me / Essaie-moi / Pruébame
Now you can secure the hook & loop closures at the back of the (C) Costume as shown.
3
2
1
C