Sunjoy L-GZ762PST-B User manual

ASSEMBLY INSTRUCTION
ITEM # L-GZ762PST-B

IMPORTANT:
1,When assembling and using this product, basic safety precautions should always be followed to reduce
the risk of personal injury and damage to equipment. Please read all instructions before assembly and
use.
2, Some parts may contain sharp edges, wear protective gloves if necessary. At least five or more people
are recommended for safe assembly.
3, Keep all children and pets away from assembly area.
4, At least 6 feet from any obstruction such as fence, garage, house, overhanging branches, laundry line
or electrical wires.
5, Do not use the unit during an el ectrical storm, as there is a r emote chance of getting struck by
lightening
6, Do not leave the gazebo assembled when there is a risk of high wind, as possible damage will occur to
the structure. Remove fabric roof and secure screen & privacy panels to poles.
7, Install on level surface.
8,Never barbecue under this gazebo or use lanterns that have open flames.
9,This package contains small items and plastic bags that should be kept away from children.
10, Check all nuts and bolts for tightness before and during usage. Ensure that all connectors and poles
are firmly secured in position fully. It is important to do so before use so as to avoid a possible collapse or
damage to the item, which could also result in injury
11,This gazebo is intended for decorative and sunshade purposes only and is not meant to withstand
extreme weather conditions including high winds, torrential rain and snow. Gazebo fabric is water
resistant, not water proof and may leak during exposure to precipitation.
WARNINGS:
1, Assembly Instructions must be followed
2, Pegs supplied must be used to hold this gazebo in place when upright.
3, Warranty does not cover damage due to extreme weather conditions.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC
This Tent Is Made With Fabric That Meets CPAI - 84 Specifications For Flame Resistance. It Is Not Fire
Proof. The Fabric Will Burn If Left In Continuous Contact With Any Flame Source
This unit is heavy. Do not assemble this item alone.

Parts List
1
1
1
1
4
4
4
4
8
4
2
2
4
4
4
8
1
1
Small roof Connector
Large roof Connector
Decoration
Hook
Small roof Pole
Upper bar
Slant beam 1
Slant beam 2
Slant beam connector
Beam1
Beam 2
Beam 3
Post1
Post 2
Large railing
Small railing
Small canopy
Large canopy
Mosquito netting
A1
A2
B1
B2
C3
C4
E2
D1
E3
F
G
H
I
J
K1
K2
L
M
N 1
P10148B01108
P10149B01108
P10041A01108
P12601C01108
P10267A01108
P11408B01108
P10341B01108
P10342B01108
P10747A01108
P11034D01108
P11035D01108
P11036D01108
P11183B01108
P11184B01108
P11225A01108
P11226A01108
P00157B07001
P00158B07001
P00341B01907

Fig.1: Insert small railing (K2) and large railing (K1) into the plate of the post I (J) then tighten the connections with
knob (AA).
Fig.2: Insert the beam (F,H,G) into the plate of the post I( J),then tighten the connections with knob (AA)
AA knobP90804A07001 32 PCS
Hardware Pack 1

Fig.3: Insert the upper bar (C4) into the connecting tube of large roof connector(A2), secure the hook（B2）to the large roof connector
(A2)
Fig.4: Insert the beam 1(D1) and beam 2(E2) into the connecting tube of upper bar (C4)
Fig.5: Insert the slant beam 1(E2) and slant beam 2(D1) into the connecting tube of slant beam connector (E3)
Fig.6: Insert the slant beam connector (E3) into the post I (J) ,then put the large canopy (M) on the assembled large roof, do not unfold
Fig.7: Insert the small roof pole (C3) into the connecting tube of small roof connector (A1) ,then put the small canopy (L)
on the assembled small roof ,do not unfold it completely.
Fig.8: Screw the decoration （B1）into the small roof connector (A1),then attach the small canopy along the small roof
pole(C3), aligning the corners and stretching it to fit it.
Fig.9: Put the large canopy (M) on the beam, do not spread it .Insert the small roof pole (C3) into the connecting tube of
upper bar (C4) .Then putthe large canopy on top of the assembled beam.
Fig.10: Secure the completely assembled gazebo on the ground by using stake (FF)
FF stakeФ6*230 16 PCSP12406C01002
Hardware Pack 2

BB Plastic ringP90701A07007 52 PCS
Hardware Pack 3
Fig.11: Attach the mosquito netting （N）on the beam H( F,G) with plastic ring (BB)