Spirit CE800 User manual

SPT0026 – CE800
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
Z100 / Z300 Z500 Z700
OWNER’S MANUAL
Elliptical

CE800 Elliptical
1
Important Safety Instructions………………………………………………………….….……3
Important Operation Instructions……………………………………………………….….…..4
Assembly Instructions………………………………………………………………….….……7
Features………………………………………………………………………………………….11
Operation of Your Elliptical…………………………………………………………………….12
Maintenance……………………………………………………………………………………..24
Exploded View Diagram and Parts List………………………………………………..……..25
Manufacturer’s Limited Warranty………………………………………………..…………… 29
Thank you for purchasing our product, please save these instructions.
Please do not perform or attempt any customizing, adjustments, repair
or maintenance that is not described in this manual.
Table of Contents

CE800 Elliptical
2
Congratulations on your new elliptical and welcome to the Spirit family!
Thank you for your purchase of this quality elliptical from Spirit Manufacturing, Inc. Your new
elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed
by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we
can to make your ownership experience as pleasant as possible for many years to come. If not
purchased direct from Spirit, the local dealership where you purchased this elliptical is your
administrator for all Spirit warranty and service needs. Their responsibility is to provide you with the
technical knowledge and service personnel to make your experience more informed and any
difficulties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone number,
and the date of purchase below to make any future, needed contact easy. We appreciate
your support and we will always remember that you are the reason that we are in business.
Please complete and mail your registration card today and enjoy your new elliptical.
Yours in Health,
BOYLES FITNESS Equipment Pty Ltd.
Name of Dealer______________________________________
Purchase Date_______________________________________
CE800 / SPT0026_ver.A

CE800 Elliptical
3
WARNING - Read all instructions before assembling, using or servicing this appliance.
■Before beginning this or any exercise program, consult a physician. This is especially important
for persons over the age of 35 or persons with pre-existing health conditions.
■If you experience nausea, dizziness or other abnormal symptoms while exercising, stop your
workout at once and consult a physician.
■To avoid muscular pain and strain, begin each workout by warming up and end it by cooling
down (slow pedaling at low resistance). Don’t forget to stretch at the end of the workout.
Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both
carpet and elliptical may result.
Keep children away from the elliptical. There are obvious pinch points and other
caution areas that can cause harm.
Keep hands away from all moving parts.
Never operate the elliptical if any of the parts are damaged. If the elliptical is not working
properly, call your dealer.
Never drop or insert any object into any openings.
Do not use outdoors.
Do not attempt to use your elliptical for any purpose other than for the purpose it is
intended.
The hand pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.
Max. user’s weight.: 150 kg
SAVE THESE INSTRUCTIONS - THINK SAFETY!
Important Safety Instructions

CE800 Elliptical
4
•Never operate the elliptical without reading and completely understanding the results of any
operational change you request from the computer.
•Do not use excessive pressure on console control keys. They are precision set to properly
function with little finger pressure. If you feel the buttons are not functioning properly with
normal pressure, contact your dealer.
•Do not attempt any servicing or adjustments other than those described in this manual. All
else must be left to trained service personnel familiar with electro-mechanical equipment and
authorized under the laws of the country in question to carry out maintenance and repair
work.
•Hold the handlebar for support when getting on or off the elliptical
•Make sure there is at least one meter of clearance between the elliptical and any fixed object.
•The safety level of this elliptical can only be ensured if you inspect all parts for signs of wear
or visible damage before each use. If a part is damaged, do not use the elliptical. Replace
any damaged parts immediately and keep the elliptical out of use until repair can be made.
•NEVER expose this elliptical to rain or moisture. This product is NOT designed for use
outdoors, near a pool or spa, or in any other high humidity environment. The operational
temperature specification is +10 to +40 degrees C, and humidity is 95%, non-condensing (no
water drops forming on surfaces).
•Place the elliptical on a firm, level surface. Place the elliptical on a protective surface to avoid
damaging the floor beneath the equipment.
•If the wattage reading on the console seems incorrect, see your local dealer for recalibration.
•The workload of this elliptical provides a speed-dependent type of exercise.
Important Operation Instructions

CE800 Elliptical
5
Assembly Pack Check List
#106 - 3/8” x 2-1/4”
Stainless Steel Bolt (4 pcs) #109 - 3/8”
Flat Washer (4 pcs)
#108 - 3/8”
Curved Washer (6 pcs)
#107 - 3/8” x 3-3/4” Stainless Steel Bolt (6 pcs)
#87 - 5/16”
Flat Washer (2 pcs)
#97 - 5/16” x 15mm
Bolt W / Loctite (2 pcs)
#103 - M6 x 15mm
Phillips Head Screw (2 pcs)
#78 - M5 x 12mm
Phillips Head Screw (14 pcs)
#76 - 5/16” x 3/4”
Hex head bolt (4 pcs)
Step1
#110 - M5 x 10mm
Phillips Head Screw
W / Loctite (8 pcs)

CE800 Elliptical
6
#75 - M8 x 25mm
Socket Cap Bolt (4 pcs)
#117 - 3/8”x 3/4”
Hex Head Bolt
W / Loctite (2 pcs)
#118 - M10
Nylon Nut (2 pcs )
#119 - M10 x 38mm
Shoulder Bolt (2 pcs)
#120 - 3/8”
Flat Washer (2 pcs)
#113 - 3.5 x 12mm
Sheet Metal Screw (14 pcs)
#78 - M5 x 12mm
Phillips Head Screw (14 pcs)
Step3
#113 - 3.5mm x 12mm
Sheet Metal Screw (4 pcs)
S
tep2
#90 - 25mm
Wave Washer (2 pcs)

CE800 Elliptical
7
STEP 1: Rear Rail and Pedal Arm Assembly
•Slide the rail assembly (2) under the rear oval stabilizer tube of the main body. Bolt the two
together with two 3/8” x 2-1/4” bolts (106) and 3/8” washers (109) from the top of the tube,
and four 3/8” x 3-3/4” bolts (107) and 3/8” curved washers (108) through the front of the oval
stabilizer. Make sure all six bolts are tightened very securely.
•Attach the two footpads (48 left & 49 right) to the pedal mounting plates with eight M5 x
10mm screws (110).
•Assemble the pedal arm assemblies (5 & 6) to the crank axles of the main body. The
bearings in the pedal arms should slide onto the axles, do not force them because damage
to the bearings can occur. The pedal arms have been previously assembled at the factory to
assure the correct fit. Secure the pedal arms with two 5/16” x 15mm bolts (97) and 5/16”
washers (87).
•Install the two covers (45 right, 46 left) over the pedal arm connection at the axle with two M6
x 15mm screws (103). Install the two wheel covers (50) with four M5 x 12mm screws (78).
•Install the four mounting brackets (17) and (26) to the rails with four 5/16” x 3/4” bolts (76).
Install the two steel covers (15 right & 16 left) by lifting the pedal arms so the wheels are off
the tracks then slide the pedal arms, wheels first, through the opening of the steel cover.
Align the cover with the mounting brackets and secure them with eight M5 x 12 mm screws
(78). Install the four small covers (2 x #19 & 2 x #20) with ten M5 x 12mm screws (78).
• Install the center aluminium step rail (72) with two 3/8” x 3-3/4” bolts (107) and curved
washers (108) at the rear and two 3/8” x 2-1/4” bolts (106) and flat washers (109) at the front.
Install the two stabilizer tube covers (64 left & 65 right) with two M5 x 12mm screws (78).
Assembly Instructions

CE800 Elliptical
8

CE800 Elliptical
9
STEP 2: Console Mast and Swing Arms
•Unravel the computer cable (30-15) and snake it through the bottom of the console mast (12)
and out the top. Secure the console mast to the main frame with four M8 x 25mm bolts (75).
Mount the console mast covers (61 left & 62 right) and secure with four 3.5mm x 12mm
screws (113).
•Install two wave washers (90) onto the console mast axle then Install the swing arms (10 left
& 11 right) onto the axles. Do not force them or use a hammer as damage to the bearings
can occur. The swing arms have been previously assembled at the factory to assure the
correct fit. Secure the arms with two 3/8” x 3/4” bolts (117) and 3/8” flat washers (120). Attach
the bottom of the swing arms to the rod ends of the pedal arms using two M10 x 38mm
shoulder bolts (119) and M10 nylon nuts (118).